DS1135
3-in-1 High-Speed Silicon
Delay Line
FEATURES
All-Silicon Timing Circuit
Three Independent Buffered Delays
Stable and Precise Over Temperature and
Voltage
Leading and Trailing Edge Precision
Preserves the Input Symmetry
Vapor Phasing, IR, and Wave Solderable
Available in Tape and Reel
Commercial and Industrial Temperature
Ranges Available
5V Operation (Refer to DS1135L for 3V
Operation)
Recommended Replacement for DS1013
and DS1035
PIN ASSIGNMENT
IN1
IN2
IN3
GND
1
2
3
4
8
7
6
5
V
CC
OUT1
OUT2
OUT3
DS1135Z 8-Pin SO (150 mils)
PIN DESCRIPTION
IN1-IN3
OUT1-OUT3
V
CC
GND
- Input Signals
- Output Signals
- +5V Supply
- Ground
DESCRIPTION
The DS1135 series is a low-power, +5V high-speed version of the popular DS1013 and DS1035.
The DS1135 series of delay lines have three independent logic buffered delays in a single package. The
device is our fastest 3-in-1 delay line. It is available in a standard 8-pin 150-mil SO.
The device features precise leading and trailing edge accuracy. It has the inherent reliability of an all-
silicon delay line solution. Each output is capable of driving up to 10 LS loads.
Standard delay values are indicated in Table 1.
19-6411; Rev 8/12
1 of 7
LOGIC DIAGRAM
Figure 1
IN
TIME DELAY
OUT
DS1135
ONE OF THREE
PART NUMBER DELAY TABLE (t
PLH
, t
PHL
)
Table 1
PART NUMBER
DS1135Z-6+
DS1135Z-8+
DS1135Z-10+
DS1135Z-12+
DS1135Z-15+
DS1135Z-20+
DS1135Z-25+
DS1135Z-30+
DELAY PER
OUTPUT
(ns)
6/6/6
8/8/8
10/10/10
12/12/12
15/15/15
20/20/20
25/25/25
30/30/30
INITIAL
TOLERANCE
(Note 1)
±1.0ns
±1.0ns
±1.0ns
±1.0ns
±1.0ns
±1.0ns
±1.5ns
±1.5ns
TOLERANCE OVER
TEMP AND VOLTAGE
(Note 2)
0°C to +70°C
-40°C to +85°C
±1.0ns
±1.5ns
±1.0ns
±1.5ns
±1.0ns
±1.5ns
±1.0ns
±1.5ns
±1.5ns
±2ns
±1.5ns
±2ns
±1.5ns
±2ns
±1.5ns
±2ns
NOTES:
1. Nominal conditions are +25°C and V
CC
=+5.0V.
2. Voltage range of 4.75V to 5.25V.
3. Delay accuracies are for both leading and trailing edges.
TEST SETUP DESCRIPTION
Figure 2 illustrates the hardware configuration used for measuring the timing parameters of the DS1135.
The input waveform is produced by a precision pulse generator under software control. Time delays are
measured by a time interval counter (20ps resolution) connected to the output. The DS1135 output taps
are selected and connected to the interval counter by a VHF switch control unit. All measurements are
fully automated with each instrument controlled by the computer over an IEEE 488 bus.
2 of 7
DS1135 TEST CIRCUIT
Figure 2
PULSE
GENERATOR
DS1135
START
3
TIME INTERVAL
COUNTER
50Ω
IN
STOP
UNIT UNDER
TEST
VHF
SWITCH
CONTROL
UNIT
TAPS 1-3
OUT
50Ω
3 of 7
Voltage Range on Any Pin Relative to Ground
Short Circuit Output Current
Operating Temperature
Storage Temperature
Lead Temperature (soldering, 10 seconds)
Soldering Temperature (reflow)
ABSOLUTE MAXIMUM RATINGS
DS1135
-1.0V to +6.0V
50mA for 1 second
-40°C to +85°C
-55°C to +125°C
+300°C
+260°C
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the
operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of
time may affect reliability.
DC ELECTRICAL CHARACTERISTICS
(V
CC
= +5V
±5%,
T
A
= -40°C to +85°C, unless otherwise noted.)
PARAMETER
Supply Voltage
Active Current
High Level Input Voltage
Low Level Input Voltage
Input Leakage
High Level Output
Current
Low Level Output Current
SYMBOL CONDITIONS
V
CC
I
CC
V
IH
V
IL
I
L
I
CC
I
CC
0V
≤
V
I
≤
V
CC
V
CC
= 4.75V,
V
OH
= 4V
V
CC
= 4.75V,
V
OL
= 0.5V
V
CC
= 5.25V,
period = 1µs
MIN
4.75
TYP
5.00
MAX
5.25
35
2.2
-0.5
-1.0
V
CC
+0.5
0.8
+1.0
-1.0
12
UNITS
V
mA
V
V
µA
mA
mA
1
1
1
1
NOTES
1
AC ELECTRICAL CHARACTERISTICS
(V
CC
= +5V
±5%,
T
A
= -40°C to +85°C, unless otherwise noted.)
PARAMETER
Period
Input Pulse Width
Input-to-Output Delay
Output Rise or Fall Time
Power-up Time
SYMBOL
t
PERIOD
t
WI
t
PLH
,
t
PHL
t
OF
, t
OR
t
PU
MIN
TYP
MAX
UNITS
ns
ns
ns
2.5
100
ns
ms
NOTES
2
2
2 (t
WI
)
100% of
Tap Delay
See Table 1
2.0
3
CAPACITANCE
(T
A
= +25°C, unless otherwise noted.)
PARAMETER
Input Capacitance
SYMBOL
C
IN
MIN
TYP
MAX
10
UNITS
pF
NOTES
4 of 7
TEST CONDITIONS
DS1135
Ambient Temperature: 25°C
±
3°C
Supply Voltage (V
CC
): 5.0V
±
0.1V
Input Pulse:
High: 3.0V
±
0.1V
Low: 0.0V
±
0.1V
Source Impedance: 50Ω Max.
Rise and Fall Time: 3.0ns Max. - Measured between 0.6V and 2.4V.
Pulse Width: 500ns
Pulse Period: 1µs
Output Load Capacitance: 15pF
Output: Each output is loaded with the equivalent of one 74F04 input gate.
Data is measured at the 1.5V level on the rising and falling edges.
Note: The above conditions are for test only and do not restrict the devices under other data sheet
conditions.
NOTES:
1. All voltages are referenced to ground.
2. Pulse width and duty cycle specifications may be exceeded; however, accuracy will be application
sensitive with respect to decoupling, layout, etc.
3. Power-up time is the time from the application of power to the time stable delays are being produced
at the output.
TIMING DIAGRAM
PERIOD
t
RISE
t
FALL
80%
IN
20%
1.5V
1.5V
1.5V
t
WI
t
PLH
t
OR
1.5V
OUT
1.5V
t
PHL
t
OF
t
WI
5 of 7
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
