EEWORLDEEWORLDEEWORLD

Part Number

Search

LTC1502IS8-3.3#TRPBF

Description
Switching Voltage Regulators Single Cell Reg Charge Pump DC/DC Conv
Categorysemiconductor    Power management   
File Size164KB,8 Pages
ManufacturerADI
Websitehttps://www.analog.com
Environmental Compliance
Download Datasheet Parametric View All

LTC1502IS8-3.3#TRPBF Overview

Switching Voltage Regulators Single Cell Reg Charge Pump DC/DC Conv

LTC1502IS8-3.3#TRPBF Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerADI
Product CategorySwitching Voltage Regulators
RoHSDetails
Mounting StyleSMD/SMT
Package / CaseSO-8
Output Voltage3.3 V
Output Current10 mA
Number of Outputs1 Output
Input Voltage MAX1.8 V
TopologyBoost
Input Voltage MIN0.9 V
Switching Frequency500 kHz
Minimum Operating Temperature- 40 C
Maximum Operating Temperature+ 85 C
PackagingReel
Height1.75 mm
Input Voltage0.9 V to 1.8 V
Operating Temperature Range- 40 C to + 85 C
TypeRegulated Charge Pump DC/DC Converter
ShutdownShutdown
Development KitDC239A
Operating Supply Current0.04 mA
Factory Pack Quantity2500
LTC1502-3.3
Single Cell to 3.3V
Regulated Charge Pump
DC/DC Converter
FEATURES
s
s
s
s
s
s
s
s
s
s
s
DESCRIPTIO
Input Voltage Range: 0.9V to 1.8V
0.9V Guaranteed Start-Up Voltage
Regulated Output Voltage: 3.3V
±4%
Output Current: 10mA (V
IN
1V)
No Inductors
Shutdown Disconnects Load from V
IN
Low Operating Current: 40µA
Low Shutdown Current: 5µA
Short-Circuit and Overtemperature Protected
Application Circuit Fits in < 0.125in
2
PCB Area
Available in 8-Pin MSOP and SO Packages
The LTC
®
1502-3.3 is a quadrupler charge pump DC/DC
converter that produces a regulated 3.3V output from a
single alkaline cell input. It requires only five small external
capacitors—no inductors are required. Low supply cur-
rent (40µA typical, 5µA in shutdown) and minimal external
components make the LTC1502-3.3 ideal for space and
power conscious single-cell applications. The total printed
circuit board area of the circuit shown below is less than
0.125in
2
.
Forcing the C1
/SHDN pin low through an external resis-
tive pull-down puts the part into shutdown mode. During
shutdown, the internal oscillator is stopped and the load is
disconnected from V
IN
. An internal pull-up current on the
C1
/SHDN pin forces the part back into normal operation
once the pull-down resistance is removed.
The LTC1502-3.3 is short-circuit protected and survives
an indefinite V
OUT
short to ground. The LTC1502-3.3 is
available in 8-pin MSOP and SO packages.
, LTC and LT are registered trademarks of Linear Technology Corporation.
APPLICATIO S
s
s
s
s
s
Pagers
Battery Backup Supplies
Portable Electronic Equipment
Handheld Medical Instruments
Glucose Meters
TYPICAL APPLICATIO
1
10µF
2
8
Single Cell to 3.3V DC/DC Converter
3.5
C2
V
OUT
7
C1
+
C3
+
1µF
LTC1502-3.3
6
3
C1
/SHDN C3
4
5
GND
V
IN
10µF
1µF
V
IN
SINGLE CELL
NiCd or
ALKALINE
1502-3.3 TA01
V
OUT
= 3.3V
I
OUT
= 10mA
3.4
OUTPUT VOLTAGE (V)
3.3
I
OUT
= 10mA
I
OUT
= 15mA
10µF
3.2
3.1
PCB LAYOUT FITS IN < 0.125IN
2
3.0
0.8
U
Output Voltage vs Input Voltage
T
A
= 25°C
1.0
1.4
1.6
1.2
INPUT VOLTAGE (V)
1.8
1502-3.3 TA02
U
U
1
BQ76930: Design help needed for BQ76930 based BMS
Q: Information about designing a BMS for LiFePO4 batteries has been posted several times (BQ78350-R1: bqStudio not showing battery voltage, BQ76930: Design help required for BQ76930). Now it's time to...
qwqwqw2088 Analogue and Mixed Signal
Op amp circuit knowledge: voltage feedback, common indicators, good and bad judgment...
What is an operational amplifier? Many textbooks and reference guides define an operational amplifier (op amp) as a special-purpose integrated circuit (IC) that can perform a variety of functions or o...
Jacktang Energy Infrastructure?
There is a problem with the industrial computer, please give me some advice!
My company has a device, the computer is used as the host computer to control PLC, PLC controls temperature control and mechanical mechanism, PLC and computer communicate via serial port, the computer...
eeleader Industrial Control Electronics
SQL CE database operation problem
if(FAILED(CoInitializeEx(NULL, COINIT_MULTITHREADED))) return FALSE; IID__Connection, (LPVOID*&m_pConn); hr = m_pConn->put_Provider(L"\\DiskOnChip\\pda\\myce.sdf"); hr = m_pConn->Open(L"Provider=micro...
zl0801 Embedded System
What does this warning mean?
"Example_2833xScia_FFDLB.c", line 172: warning: variable "Error" was declared but never referenced, how to fix it...
flyfish1986 DSP and ARM Processors
Online help on how to initialize TI's ads1252! ????
I have been working on this for a long time, but I still can't get it right. I hope someone who has done this before can give me some suggestions and advice. There is too little information about ADS1...
海盗郭兆广 TI Technology Forum

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1884  2199  2634  2761  2795  38  45  54  56  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号