EXPOSED PAD (PIN 9) IS OUT, MUST BE SOLDERED TO OUT
ON THE PCB. SEE THE APPLICATIONS INFORMATION SECTION.
ST PACKAGE
3-LEAD PLASTIC SOT-223
T
JMAX
= 125°C,
θ
JA
= 24°C/W,
θ
JC
= 15°C/W
TAB IS OUT, MUST BE SOLDERED TO OUT ON THE PCB.
SEE THE APPLICATIONS INFORMATION SECTION.
TS8 PACKAGE
8-LEAD PLASTIC TSOT-23
T
JMAX
= 125°C,
θ
JA
= 57°C/W,
θ
JC
= 15°C/W
2
3092fc
For more information
www.linear.com/LT3092
LT3092
orDer inForMaTion
LEAD FREE FINISH
LT3092EDD#PBF
LT3092IDD#PBF
LT3092EST#PBF
LT3092IST#PBF
LT3092MPST#PBF
LT3092ETS8#PBF
LT3092ITS8#PBF
LEAD BASED FINISH
LT3092EDD
LT3092IDD
LT3092EST
LT3092IST
LT3092MPST
LT3092ETS8
LT3092ITS8
TAPE AND REEL
LT3092EDD#TRPBF
LT3092IDD#TRPBF
LT3092EST#TRPBF
LT3092IST#TRPBF
LT3092MPST#TRPBF
LT3092ETS8#TRPBF
LT3092ITS8#TRPBF
TAPE AND REEL
LT3092EDD#TR
LT3092IDD#TR
LT3092EST#TR
LT3092IST#TR
LT3092MPST#TR
LT3092ETS8#TR
LT3092ITS8#TR
http://www.linear.com/product/LT3092#orderinfo
PART MARKING*
LFJD
LFJD
3092
3092
3092MP
LTFJW
LTFJW
PART MARKING*
LFJD
LFJD
3092
3092
3092MP
LTFJW
LTFJW
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
8-Lead Plastic SOT-23
8-Lead Plastic SOT-23
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
8-Lead Plastic SOT-23
8-Lead Plastic SOT-23
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–40°C to 125°C
–40°C to 125°C
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
3092fc
For more information
www.linear.com/LT3092
3
LT3092
elecTrical characTerisTics
PARAMETER
SET Pin Current
Offset Voltage (V
OUT
– V
SET
)
Current Regulation (Note 7)
Line Regulation
Minimum Load Current (Note 3)
Dropout Voltage (Note 4)
Current Limit
Reference Current RMS Output Noise (Note 5)
Ripple Rejection
I
SET
V
OS
∆I
SET
∆V
OS
∆I
SET
∆V
OS
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C. (Note 2)
CONDITIONS
V
IN
= 2V, I
LOAD
= 1mA
2V ≤ V
IN
≤ 40V, 1mA ≤ I
LOAD
≤ 200mA
V
IN
= 2V, I
LOAD
= 1mA
V
IN
= 2V, I
LOAD
= 1mA
∆I
LOAD
= 1mA to 200mA
∆I
LOAD
= 1mA to 200mA
∆V
IN
= 2V to 40V, I
LOAD
= 1mA
∆V
IN
= 2V to 40V, I
LOAD
= 1mA
2V ≤ V
IN
≤ 40V
I
LOAD
= 10mA
I
LOAD
= 200mA
V
IN
= 5V, V
SET
= 0V, V
OUT
= –0.1V
10Hz ≤ f ≤ 100kHz
f = 120Hz, V
RIPPLE
= 0.5V
P-P
, I
LOAD
= 0.1A,
C
SET
= 0.1µF, C
OUT
= 2.2µF
f = 10kHz
f = 1MHz
I
SET
10ms Pulse
l
l
l
l
l
l
l
MIN
9.9
9.8
–2
–4
TYP
10
10
MAX
10.1
10.2
2
4
UNITS
µA
µA
mV
mV
nA
mV
nA/V
mV/V
µA
V
V
mA
nA
RMS
dB
dB
dB
%/W
–0.1
–0.5
0.03
0.003
300
1.22
1.3
200
300
0.7
90
75
20
0.003
–2
0.2
0.010
500
1.45
1.65
Thermal Regulation
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Unless otherwise specified, all voltages are with respect to V
OUT
.
The LT3092E is tested and specified under pulse load conditions such
that T
J
@
T
A
. The LT3092E is 100% tested at T
A
= 25°C. Performance at
–40°C and 125°C is assured by design, characterization, and correlation
with statistical process controls. The LT3092I is guaranteed to meet all
data sheet specifications over the full –40°C to 125°C operating junction
temperature range. The LT3092MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 3:
Minimum load current is equivalent to the quiescent current of
the part. Since all quiescent and drive current is delivered to the output
of the part, the minimum load current is the minimum current required to
maintain regulation.
Note 4:
For the LT3092, dropout is specified as the minimum input-to-
output voltage differential required supplying a given output current.
Note 5:
Adding a small capacitor across the reference current resistor
lowers output noise. Adding this capacitor bypasses the resistor shot noise
and reference current noise (see the Applications Information section).
Note 6:
Diodes with series 1k resistors clamp the SET pin to the OUT pin.
These diodes and resistors only carry current under transient overloads.
Note 7:
Current regulation is Kelvin-sensed at the package.
Note 8:
This IC includes overtemperature protection that protects the
device during momentary overload conditions. Junction temperature
exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
The NiMH battery is 3.6V, and the low voltage protection is usually around 3V. When it is fully charged and used normally, it is discharged. When the LED discharges below 3V, it is protected and shut ...
In the STM32 branch, the USB enable option has been added. The default is disabled (not added). #define MICROPY_HW_ENABLE_USB (1) If this option is not added, there will be no USB device after the upg...
2013 Korea Building Materials Exhibition Seoul Building Materials Exhibition 2012 Korea Building Materials Exhibition 2012 Seoul Building Materials Exhibition Korea Decoration Exhibition 2012 Korea De...
Temperature resistance of 210℃, used in aerospace or underground. Haha, I don't know how I applied for it. It's more than 500 yuan per piece. I may not be able to buy it. Haha. Thanks to TI. But it's ...
When MSP430 communicates with the computer via serial port, the receiving end of MSP430 can be seen to receive data continuously, but the data cannot be connected to the PC. Moreover, when the host se...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
Spatial Division Multiplexing (SDM) MIMO processing can significantly improve spectrum efficiency and thus greatly increase the capacity of wireless communication systems. Spatial Division Multip...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
