Note: Inclusive of initial frequency accuracy, operating temperature range, supply variation, load variation, 3 times solder reflow, shock, vibration and 1 year aging at 25°C. We do not
recommend hand soldering the devices
JUNE 20, 2017
3
IDT XO HCMOS CRYSTAL OSCILLATOR
XLH DATASHEET
DC Characteristics
(V
DD
= 2.5V
±5%, T
A
= - 20°C to +70°C; -40° to +85°C)
Parameter
Power Supply Current
Output HIGH Voltage
Output LOW Voltage
Enable/Disable Input HIGH Voltage
(Output enabled)*
Enable/Disable Input LOW Voltage
(Output disabled)
Symbol
I
DD
V
OH
V
OL
V
IH
V
IL
Condition
Standard Frequencies
Fout = 0.750 to 160MHz
Fout = 160+ to 180MHz
Fout = 0.750 to 160MHz
Fout = 160+ to 180MHz
Min
10%V
DD
20%V
DD
Typ
Max
35
Units
mA
V
10%V
DD
20%V
DD
70%V
DD
30%V
DD
V
V
V
* A pullup resistor from pin 4 (VDD) to pin 1 (E/D) enables output when pin 1 is left open.
Note: Inclusive of initial frequency accuracy, operating temperature range, supply variation, load variation, 3 times solder reflow, shock, vibration and 1 year aging at 25°C. We do not
[size=5]The information I have collected recently is summarized below, including Renesas development board routines, quadcopter information, AD9850_AD9851_module[/size]...
I would like to ask how I assigned the pins of 430f149 to the RF module (the ones with * are RF module signals
I don't know if this allocation of clk and data transceiver is feasible. Please give me s...
[i=s]This post was last edited by dcexpert on 2017-12-5 14:12[/i] [size=14px]The MicroPython Getting Started Guide is finally officially published. [/size] [img=300,407]http://www.micropython.org.cn/b...
Micropython has started to support the onboard 16M SDRAM of the STM32F7Disc development board. I will find time to update and review the new firmware in the near future. [url=https://github.com/microp...
Dear all the experts, I am working on a 50W power supply project recently. The input is 230V, the output is 24V, the electronic load pulls 2.4A, the reverse withstand voltage of the tube is about 400V...
1. When the system to be debugged becomes larger, unstable phenomena occasionally occur. For example, after downloading is completed, the system needs to be interrupted. At this time, when the interru...
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
Rated capacity refers to the maximum output power of the UPS (the product of voltage V and current A).
Usually, the UPS power supplies sold on the market are marked with "W" (watt) for smaller...[Details]
1 Introduction
Automatic Test
System The ATS (Automatic Test System) integrates all the stimulus and measurement equipment required for testing.
The computer
efficiently comp...[Details]
Traditionally, when using PLC to control stepper motors, a dedicated stepper motor control intelligent module is usually added to the PLC, and then connected to the drive power supply to realize th...[Details]
TPMS is the abbreviation of "Tire Pressure Monitoring System". It is mainly used to automatically monitor the tire pressure in real time when the car is driving, and to alarm for tire leakage and l...[Details]
(1) Open circuit voltage of the battery
(2) Internal resistance of the battery
(3) Battery operating voltage
(4) Charging voltage
Charging voltage refers to the voltage applied ...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
