Bi-directional pin. Upon power-on, the value of VDD_SEL is latched in and used to
select the power (see Power Selection table 2 ). Internal pull down defaults SST1 to 0,
use external pull-up to set to 1. After power-up this pin acts as 12MHz output clock.
Bi-directional and Tri-level pin. Upon power-on, the value of SEL10_8 is latched in and
used to select the output frequency (See frequency selection table 3 ). Tri level input: M
= Do not connect, 1 = Pull up, 0 = Pull down. After power-up this pin acts as 10MHz
clock, 8MHz clock, or “No output”, depending on SEL10_8.
Ground connection.
Bi-directional pin. Upon power-on, the value of XTAL_SEL is latched in and used to set
the input crystal frequency (24.575MHz or 14.31818MHz). Set XTAL_SEL to 0 (default)
for 24.576MHz input crystal, set XTAL_SEL to 1 for 14.31818MHz input crystal (see
Crystal Selection Table on page 1). . After power-up this pin acts as 27MHz output
(with 24.576MHz crystal) or as 14.31818MHz pass through clock (with 14.31818MHz
crystal), depending on the input crystal.
The 27MHz output can be modulated for low EMI using Spread Spectrum.
3.3V power supply for 27MHz, 10MHz, 12MHz, and 24.576MHz.
24.576MHz/SST1
VDDB1
VDD25M
25MHzx2
VSS25M
12MHz/VDD_SEL
7
8
9
10
11
12
B
P
P
O
P
B
10_8MHz/SEL10_8
VSSB2
13
14
B
P
27_14.318MHz/XTAL_SEL
15
B
VDDB2
16
P
FUNCTIONAL DESCRIPTION
Tri-level and two-level inputs
In order to reduce pin usage, the PLL702-02 uses tri-level input pins. These pins allow 3 levels for input selection: namely, 0 =
Connect to GND, 1 = Connect to VDD, M = Do not connect. Thus, unlike the two-level selection pins, the tri-level input pins are
in the “M” (mid) state when not connected. In order to connect a tri-level pin to a logical “zero”, the pin must be connected to
GND. Likewise, in order to connect to a logical “one”, the pin must be connected to VDD.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 08/30/05 Page 3
PLL702-02
Low EMI Peripheral Clock Generator for Notebook & Motherboards
Connecting a bi-directional pin
The PLL702-02 also uses bi-directional pins. The same pin serves as input upon power-up, and as output as soon as the inputs
have been latched. The value of the input is latched-in upon power-up. Depending on the pin (see pin description), the input can
be tri-level or a standard two-level. Unlike unidirectional pins, bi-directional pins cannot be connected directly to GND or VDD in
order to set the input to "0" or "1", since the pin also needs to serve as output. In the case of two level input pins, an internal pull-
up resistor is present. This allows a default value to be set when no external pull down resistor is connected between the pin
and GND (by definition, a tri-level input has a the default value of "M" (mid) if it is not connected). In order to connect a bi-
directional pin to a non-default value, the input must be connected to GND or VDD through an external pull-down/pull-up
resistor.
Note:
when the output load presents a low impedance in comparison to the internal pull-up resistor, the internal pull-up resistor
may not be sufficient to pull the input up to a logical “one”, and an external pull-up resistor may be required.
For bi-directional inputs, the external loading resistor between the pin and GND has to be sufficiently small (compared to the
internal pull-up resistor) so that the pin voltage be pulled below 0.8V (logical “zero”). In order to avoid loading effects when the
pin serves as output, the value of the external pull-down resistor should however be kept as large as possible. In general, it is
recommended to use an external resistor of around one sixth to one quarter of the internal pull-up resistor (see Application
Diagram).
Note:
when the output is used to drive a load presenting an small resistance between the output pin and VDD, this resistance is
in essence connected in parallel to the internal pull-up resistor. In such a case, the external pull-down resistor may have to be
dimensioned smaller to guarantee that the pin voltage will be low enough achieve the desired logical “zero”. This is particularly
true when driving 74FXX TTL components.
APPLICATION DIAGRAM: BI-DIRECTIONAL PINS WITH INTERNAL PULL-UP
Internal to chip
VDD
External Circuitry
R
up
Power Up
Reset
R
RB
Output
EN
Bi-directional pin
Clock Load
Latched
Input
Latch
R
UP
/
4
Jumper options
NOTE:
Rup=Internal pull-up resistor (see pin description). Power-up Reset : R starts from 1 to 0 while RB starts from 0 to 1.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 08/30/05 Page 4
PLL702-02
Low EMI Peripheral Clock Generator for Notebook & Motherboards
Electrical Specifications
1. Absolute Maximum Ratings
PARAMETERS
Supply Voltage
Input Voltage, dc
Output Voltage, dc
Storage Temperature
Ambient Operating Temperature*
Junction Temperature
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
SYMBOL
V
DD
V
I
V
O
T
S
T
A
T
J
MIN.
-0.5
-0.5
-65
-40
MAX.
4.6
V
DD
+0.5
V
DD
+0.5
150
85
125
260
2
UNITS
V
V
V
°C
°C
°C
°C
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product
reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this
specification is not implied.
*
Note:
Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
2. AC Specifications
PARAMETERS
Input Frequency (to be set via XTAL_SEL)
Output Rise Time
Output Fall Time
Duty Cycle
Duty Cycle 8MHz clock
Max. Absolute Period Jitter
Max. Jitter, cycle to cycle
CONDITIONS
+/- 20ppm accuracy
0.8V to 2.0V with no load
2.0V to 0.8V with no load
At VDD/2
At VDD/2
Long term, No SST
Long term + Short term
MIN.
TYP.
14.31818
24.576
MAX.
UNITS
MHz
MHz
1.5
1.5
45
43
50
50
55
57
150
120
ns
ns
%
%
ps
ps
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
I saw a piece of news and I don't quite believe it:Gree Chairman Ms. Dong said: Gree has spent nine years developing a zero-carbon source air conditioner, which can generate electricity through the ai...
In the driver that comes with Windows, there is a setting (Link speed/duplex mode) in the properties of the local connection -> advanced options. You can select the speed of the network card (10M/100M...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:01[/i] The three primary colors can be mixed into various colors. Is it the same for LED color mixing? In natural light, as long as the...
I received a 5969 board from TI and EEworld a while ago. It is my first time using TI chips. I will find some information to learn more about it. I will continue the competition after I learn how to l...
I have made a serial port that can receive a character, but the string is not correct. Can anyone give me some advice? I input a string in serial windows #1 and enter the corresponding execution progr...
First of all, I want to say that the library function description given by MXCHIP is a bit too simple, or it is a problem with my download. If anyone has a more detailed description, I hope to share i...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
To understand how and why OLED power supply affects display image quality, you must first understand OLED display technology and power supply requirements. This article will explain the latest OLED...[Details]
introduction
Incandescent bulbs can emit a variety of light, but in specific applications, only green, red, and yellow light are usually needed - such as traffic lights. If an incand...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
1 Battery technology determines the fate of energy vehicles
Regardless of whether new energy vehicles are hybrid or pure electric vehicles, they cannot do without the core technology of batter...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
Traditionally, when using PLC to control stepper motors, a dedicated stepper motor control intelligent module is usually added to the PLC, and then connected to the drive power supply to realize th...[Details]
The rapid development of the automobile industry has promoted the progress of global machinery, energy and other industries, as well as the development of economy, transportation and other aspects,...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
