C062C569G1R5TA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > C062C569G1R5TA

Preview

C062C569G1R5TA: DescriptionCERAMIC MOLDED/AXIAL & RADIAL - STANDARD; File Size135KB，10 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet View All

C062C569G1R5TA Overview

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Preview

Download Datasheet

View All

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G – 50, 100 & 200 Volts

X7R – 50, 100 & 200 Volts

Temperature Characteristics:

C0G – 0 ±30 PPM/°C from -55°C to +125°C

X7R – ±15% from -55°C to +125°C

Capacitance Tolerance:

C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance)

X7R – ±10%, ±20%, -0 +100%, -20% +80%

Construction:

Monolithic block of ceramic dielectric with interdigitated

internal electrodes, encapsulated in a molded case, and

having axial or radial leads. Meets flame test requirements

of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,

Condition A, except 20 cycles.

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits

at 25°C are:

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2

seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).

Depth of immersion — to a minimum of .050" from the

capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper standard; 100% tin plated optional

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms

at 1 kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).

C0G – .15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K megohms or 1000 megohm - µF, whichever

is less.

X7R – 100K megohms or 1000 megohm - µF, whichever

is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited

to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test

limits at 25°C are:

Capacitance Change:

C0G – less than 3% or 0.25 pF, whichever is higher

X7R – ±20% of initial value

Dissipation Factor:

C0G – .25% maximum

X7R – 3.0% maximum

Recommended Resources

Remote control socket circuit

High Q Band Pass Filter Amplifier

Negative 2V-12V reference voltage source

Simple infrared control music device circuit diagram

Amplification circuit for lead sulfide photoelectric components

Infrared remote control multi-way switch controller

Can the reset resistor be saved?: [size=14px]I use RC to make a low-level reset circuit, but the reset pin of the microcontroller already has an internal pull-up resistor (220k-500k). Can I omit R and connect a capacitor directly? I h...; momn12 Embedded System

Keyboard and Display: Keyboard and Display...; sjs199023 MCU

How to check the segment address under wince: data.load.exe $REL\eboot.exe /nocode /reloc .text at 0x80039000 /reloc .data at 0x80021000 Here 0x80039000 indicates the address of the code segment of eboot at runtime; 0x80021000 indicates the start...; casper Embedded System

Looking for a hardware job! Let me say a few words!: It is so hard to find a job now! My friend graduated in 2008 with a degree in electronics. He wants to find a job in software or hardware, but he hasn't found one yet! He didn't even get a call (he ap...; raphael84 Embedded System

Is it correct to do this in the zero-crossing detection circuit?: The requirement is: when the voltages of the two signals are equal, a trigger signal is generated. After the two signals are subtracted, the zero-point signal is detected. The time requirement is high...; yinyuanyuan Analog electronics

[Atmel SAM R21 Creative Competition Weekly Plan] + GPU Run: Well, after some trouble, it's basically going smoothly. The GPU has been driven. For GPU related information, please refer to the previous post. [url=https://bbs.eeworld.com.cn/thread-457105-1-1.html...; lyzhangxiang Microchip MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components