C052C479H5G5CA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > C052C479H5G5CA

Preview

C052C479H5G5CA: DescriptionCERAMIC MOLDED/AXIAL & RADIAL - STANDARD; File Size135KB，10 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet View All

C052C479H5G5CA Overview

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Preview

Download Datasheet

View All

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G – 50, 100 & 200 Volts

X7R – 50, 100 & 200 Volts

Temperature Characteristics:

C0G – 0 ±30 PPM/°C from -55°C to +125°C

X7R – ±15% from -55°C to +125°C

Capacitance Tolerance:

C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance)

X7R – ±10%, ±20%, -0 +100%, -20% +80%

Construction:

Monolithic block of ceramic dielectric with interdigitated

internal electrodes, encapsulated in a molded case, and

having axial or radial leads. Meets flame test requirements

of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,

Condition A, except 20 cycles.

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits

at 25°C are:

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2

seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).

Depth of immersion — to a minimum of .050" from the

capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper standard; 100% tin plated optional

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms

at 1 kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).

C0G – .15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K megohms or 1000 megohm - µF, whichever

is less.

X7R – 100K megohms or 1000 megohm - µF, whichever

is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited

to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test

limits at 25°C are:

Capacitance Change:

C0G – less than 3% or 0.25 pF, whichever is higher

X7R – ±20% of initial value

Dissipation Factor:

C0G – .25% maximum

X7R – 3.0% maximum

Recommended Resources

common collector circuit

Brushless DC motor circuit

Beep electronic thermometer circuit

555RS trigger working mode circuit

Double pulse generator circuit

Computer motherboard circuit diagram 440LX_33

【Original】Why can’t I set the segment point? ! !: Using C-SPY debugger, I can set segment points in the assembly program, but I can't set them in the corresponding C program. Why?...; wangmengjun123 Microcontroller MCU

The influence of thermoelectric potential on precision voltage measurement: [i=s] This post was last edited by dontium on 2015-1-23 11:42 [/i] Original link [url] deyisupport./blog/b/signalchain/archive/2013/01/17/51394.aspx [/url] [img] deyisupport./resized-image.ashx/__size...; zca123 Analogue and Mixed Signal

Ferroelectric 430: I have been using 430 for quite some time. The very first project used the internal flash of 430 for storage. The frequent read and write operations caused bad blocks in the flash after one year. I am...; rengo Microcontroller MCU

Doubts about copper coating when drawing PCB boards: [color=#333333]I didn’t understand the definition of copper coating when I first started drawing PCB boards[/color] [color=#333333]And now I have a 4-layer board[/color] [color=#333333]I see that the ...; shaorc PCB Design

Data acquisition and processing software programming skills based on LabVIEW: Data Acquisition and Processing Software Programming Skills Based on LabVIEW [size=2] (Shijiazhuang Railway Institute) Yan Yan, Ma Zengqiang, Yang Ming Abstract: Aiming at the problems often encounter...; wanggq Test/Measurement

CRC Check and C Language Implementation: Learn together and make progress together...; cqwjfb Programming Basics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components