M38510-101J datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > M38510-101J

Preview

M38510-101J: DescriptionMICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON; File Size247KB，43 Pages; ManufacturerETC

Download Datasheet Compare View All

M38510-101J Overview

MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON

Preview

Download Datasheet

View All

INCH-POUND

MIL-M-38510/101J

07 February 2003

SUPERSEDING

MIL-M-38510/101H

30 October 2001

MILITARY SPECIFICATION

MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON

This specification is approved for use by all Departments and Agencies of the Department of Defense.

Inactive for new design after 13 July 1995.

1. SCOPE

1.1 Scope. This specification covers the detail requirements for monolithic silicon, operational amplifiers. Two product

assurance classes and a choice of case outlines and lead finish are provided for each type and are reflected in the complete

part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, (see 6.3).

1.2 Part number. The complete part number shall be in accordance with MIL-PRF-38535, and as specified herein..

1.2.1 Device types. The device types shall be as shown in the following:

Device type

Circuit

Single operational amplifier - internally compensated

Dual operational amplifier - internally compensated

Single operational amplifier - externally compensated

Dual operational amplifier - externally compensated 1/

Single operational amplifier, high speed

Dual operational amplifier - internally compensated

1.2.2 Device class. The device class shall be the product assurance level as defined in MIL-PRF-38535.

______

1/ Device types 05 and 06 may be monolithic, or they may consist of two separate, independent die.

Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be use

in improving this document should be addressed to: Commander, Defense Supply Center Columbus,

ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43216-5000, by using the Standardization

Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.

AMSC N/A

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

FSC 5962

MIL-M-38510/101J

3. REQUIREMENTS

3.1 Qualification. Microcircuits furnished under this specification shall be products that are manufactured by a

manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturers list before contract

award (see 4.3 and 6.4).

3.2 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535 and as specified

herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall

not affect the form, fit, or function as described herein.

3.3 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as

specified in MIL-PRF-38535 and herein.

3.3.1 Terminal connections. The terminal connections shall be as specified on figure 1.

3.3.2 Schematic circuits. The schematic circuits shall be maintained by the manufacturer and made available to the

qualifying activity and the preparing activity (DSCC-VAS) upon request.

3.3.3 Case outlines. The case outlines shall be as specified in 1.2.3.

3.4 Lead material and finish. Lead material and finish shall be in accordance with MIL-PRF-38535 (see 6.6).

3.5 Electrical performance characteristics. The following electrical performance characteristics apply over the full

operating ambient temperature range of -55°C to +125°C and for supply voltages

±5

V dc to

±20

V dc, unless otherwise

specified (see table I).

3.5.1 Offset null circuits. Each amplifier having nulling inputs (device types 01, 02, 03, 05, and 07) shall be capable of

being nulled 1 mV beyond the specified offset voltage limits for -55°C

≤

+125°C using the circuits of figure 2.

3.5.2 Frequency compensation. Device types 01, 02, 07, and 08 shall be free of oscillation when operated in a unity gain

non-inverting mode with no external compensation and a source resistance of

≤

10 kΩ, and when operated in any test

condition specified herein. Device types 03, 04, 05, and 06 shall be free from oscillation when compensated with a 30 pF

capacitor for all gain configurations or a 3 pF capacitor when used with a gain of 10.

3.6 Rebonding. Rebonding shall be in accordance with MIL-PRF-38535.

3.7 Electrical test requirements. Electrical test requirements for each device class shall be the subgroups specified in

table II. The electrical tests for each subgroup are described in table III.

3.8 Marking. Marking shall be in accordance with MIL-PRF-38535.

3.9 Microcircuit group assignment. The devices covered by this specification shall be in microcircuit group number 49

(see MIL-PRF-38535, appendix A).

M38510-101J Related Products

	M38510-101J	M38510-10	MIL-M-38510	MIL-M-385101H	MIL-M-385101J
Description	MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON	MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON	MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON	MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON	MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON

Recommended Resources

Voice control signal acquisition circuit diagram

Floating adjustable regulated power supply circuit diagram a using μA723

Thermostatic control circuit

Synchronous pulse width modulation circuit

Telephone line working status monitoring circuit

810 computer motherboard circuit diagram_33

Chapter IV - Monolithic Difference Amplifiers: Chapter IV - Monolithic Difference Amplifiers...; 安_然 Analog electronics

PIC microcontroller KIT2 emulator (Shenzhen Gelanrui Technology Co., Ltd.): PIC KIT2 is a PIC microcontroller development tool that is fully compatible with the newly launched PICKIT 2 from Microchip. It can program almost all of Microchip's flash microcontrollers. It can als...; GLRDLANLAN Microchip MCU

About the price of modules capable of collecting electrical parameters and analog quantities: What is the price of the module that can collect electrical parameters (requires the ability to control switches) and analog quantity acquisition? The above requirements are: intrinsically safe, matur...; my_lemontree13 Embedded System

How to make TQAM3358 startup card: To make a 3358 boot card, the operation method is as follows: (The following takes the Android system as an example) 1. Insert the SD card into the card reader and connect it to the computer, then ope...; 小小宇宙 ARM Technology

A question about USB driver development.: I want to implement a USB driver now. I have never written a USB driver before and I don't know much about it. Please give me some advice: Use the USB driver of the Windows system to develop a user-mo...; shamuwhale Embedded System

SensorTile SD card test, "overhead" soldering: [size=5]I have wanted to test the SD card and humidity sensor of SensorTile for a long time[/size] [size=5]But I need to solder the small board to the CRADLE board[/size] [size=5]Once soldered, it can...; littleshrimp MEMS sensors

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components