to minimize resistive DC losses. Long-term hermeticity
is assured through use of parallel seam welded lid
attachment along with International Rectifier’s rugged
ceramic pin-to-package seal. Axial orientation of the
leads facilitates preferred bulkhead mounting to the
principal heat-dissipating surface.
Manufactured in a facility fully qualified to MIL-PRF-38534,
class K, these converters are fabricated utilizing DSCC
qualified processes and are fully compliant to Class K.
The complete suite of PI tests has been completed
including Group C life test. Variations in electrical,
mechanical and screening specifications can be
accommodated. Contact IR Santa Clara for special
requirements.
28V Input, Triple Output
ART
Features
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Total Dose > 100 krad (Si), 2:1margin
No SEE to LET > 83 Mev
.
cm
2
/mg
Derated per MIL-STD-975 & MIL-STD-1547
Output Power Range 3 to 30 Watts
19 to 50 Volt Input Range
Input Undervoltage Lockout
High Electrical Efficiency > 83%
Full Performance from -55°C to +125°C
Continuous Short Circuit and Overload
Protection
12.8 W/in
3
Output Power Density
True Hermetic Package
External Inhibit Port
Externally Synchronizable
Fault Tolerant Design
5V,
±
12V or
±
15 V Outputs Available
www.irf.com
1
08/12/04
ART28XXT Series
SPECIFICATIONS
Absolute Maximum/Minimum Ratings
Note1
Recommended Operating Conditions
Note 2
Input Voltage
Minimum Output Current
Soldering Temperature
Storage Temperature
-0.5V to 80V
5% maximum rated
current, any output
300°C for 10 seconds
-65°C to +135°C
19V to 60V
19V to 50V for full derating
to MIL-STD-975
Output Power Range
3W to 30 W
Operating Temperature -55°C to +125°C
-55°C to +85°C for full
derating to MIL-STD-975
Input Voltage Range
Electrical Performance
-55°C < T
CASE
< +125°C, V
IN
=28V, C
L
=0
unless otherwise specified.
Parameter
Output voltage accuracy
Symbol
V
OUT
Conditions
I
OUT
= 1.5Adc, T
C
= +25°C
(main)
Min
4.95
±11.50
±14.50
3.0
(main)
(dual)
(main)
(dual)
(main)
(dual)
(main)
150
75
-15
-60
-180
-300
-10
-500
4.8
±11.1
±13.9
Max
5.05
Units
Vdc
I
OUT
= ±250mAdc, T
C
= +25°C ART2812(dual)
I
OUT
= ±250mAdc, T
C
= +25°C ART2815(dual)
Output power
Note 5
Output current
Note 5
P
OUT
I
OUT
19 Vdc< V
IN
< 50Vdc
19 Vdc< V
IN
< 50Vdc
150 mAdc < I
OUT
< 3000 mAdc
Line regulation
Note 3
VR
LINE
19 Vdc< V
IN
< 50Vdc
±75 mAdc < I
OUT
< ±750 mAdc
150 mAdc < I
OUT
< 3000 mAdc
Load regulation
Note 4
VR
LOAD
19 Vdc< V
IN
< 50Vdc
±75 mAdc < I
OUT
< ±750 mAdc
Cross regulation
Note 8
VR
CROSS
19 Vdc< V
IN
< 50Vdc
(dual)
Total regulation
VR
All conditions of Line, Load,
(main)
Cross Regulation, Aging,
Temperature and Radiation ART2812(dual)
ART2815(dual)
I
OUT
= minimum rated, Pin 3 open
Pin 3 shorted to pin 2 (disabled)
19 Vdc< V
IN
< 50Vdc
I
OUT
= 3000 mAdc (main), ±500 mAdc (dual)
19 Vdc< V
IN
< 50Vdc
I
OUT
= 3000 mAdc (main), ±500 mAdc (dual)
Sychronization input open. (pin 6)
I
OUT
= 3000 mAdc (main), ±500 mAdc (dual)
±12.50
±15.15
30
3000
750
+15
mV
+60
+180
mV
+300
+10
mV
+500
5.2
V
±12.9
±16.0
250
8.0
70
100
mA
mV
p.p
mA
p.p
kHz
%
W
mAdc
Input current
Output ripple voltage
Note 6
Input ripple current
Note 6
Switching frequency
Efficiency
I
IN
V
RIP
I
RIP
F
S
Eff
225
83
275
For Notes to SPECIFICATIONS, refer to page 3
2
www.irf.com
ART28XXT Series
Electrical Performance
(Continued)
Parameter
Enable Input
open circuit voltage
drive current (sink)
voltage range
Synchronization Input
frequency range
pulse high level
pulse low level
pulse rise time
pulse duty cycle
Synchronization Output
pulse high level
pulse low level
Power dissipation, load fault
Output response to step load
changes
Notes 7, 11
Recovery time from step load
changes
Notes 11, 12
Output response to step line
changes
Notes 10, 11
Recovery time from step line
changes
Notes 10, 11,13
Turn on overshoot
V
OS
Turn on delay
Note 14
Capacitive load
Notes 9, 10
Isolation
T
DLY
CL
ISO
I
OUT
= minimum and full rated
I
OUT
= minimum and full rated
No effect on DC performance
(main)
(dual)
100
P
D
V
TLD
T
TLD
V
TLN
External clock signal on Sync. input (pin 4)
Symbol
Conditions
MIN
3.0
0.1
-0.5
225
4.5
-0.5
40
20
3.7
0.0
MAX
5.0
50.0
310
10.0
0.25
80
4.3
0.25
16
Units
V
mA
V
Khz
V
V
V/µS
%
V
W
mV
PK
µS
mV
PK
Signal compatible with synchronization input
Short circuit, any output
10% Load to/from 50% load
50% Load to/from 100% load
10% Load to/from 50% load
50% Load to/from 100% load
I
OUT
= 3000 mAdc
V
IN
= 19 V to/from 50 V
I
OUT
= ±500 mAdc
I
OUT
= 3000 mAdc
V
IN
= 19 V to/from 50 V
I
OUT
= ±500 mAdc
(main)
(dual)
(main)
(dual)
(main)
(dual)
5.0
-350
-1050
-200
-200
200
200
200
200
350
1050
500
500
100
500
20
500
100
T
TLN
µS
mV
mS
µF
MΩ
500VDC Input to Output or any pin to case
(except pin 12)
Notes to SPECIFICATIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Operation outside absolute maximum/minimum limits may cause permanent damage to the device. Extended operation at the limits may permanently
degrade performance and affect reliability.
Device performance specified in Electrical Performance table is guaranteed when operated within recommended limits. Operation outside
recommended limits is not specified.
Parameter measured from 28V to 19 V or to 50V while loads remain fixed.
Parameter measured from nominal to minimum or maximum load conditions while line remains fixed.
Up to 750 mA is available from the dual outputs provided the total output power does not exceed 30W.
Guaranteed for a bandwidth of DC to 20MHz. Tested using a 20KHz to 2MHz bandwidth.
Load current is stepped for output under test while other outputs are fixed at half rated load.
Load current is fixed for output under test while other output loads are varied for any combination of minimum to maximum.
A capacitive load of any value from 0 to the specified maximum is permitted without comprise to DC performance. A capacitive load in excess of the
maximum limit may interfere with the proper operation of the converter’s short circuit protection, causing erratic behavior during turn on.
Parameter is tested as part of design characterization or after design or process changes. Thereafter, parameters shall be guaranteed to the limits
specified in the table.
Load transient rate of change, di/dt
≤
2 A/µSec.
Recovery time is measured from the initiation of the transient to where V
OUT
has returned to within ±1% of its steady state value.
Line transient rate of change, dv/dt
≤
50 V/µSec.
Turn on delay time is for either a step application of input power or a logical low to high transition on the enable pin (pin 3) while power is present at the
input.
www.irf.com
3
ART28XXT Series
Group A Tests
V
IN
= 28Volts, C
L
=0
unless otherwise specified.
Test
Output voltage accuracy
Symbol
V
OUT
Conditions unless otherwise specified
I
OUT
= 1.5 Adc
I
OUT
= ±250mAdc
I
OUT
= ±250mAdc
V
IN
= 19 V, 28V, 50 V
(main)
V
IN
19 V, 28V, 50 V
I
OUT
= 150, 1500, 3000mAdc
V
IN
= 19 V, 28V, 50 V
I
OUT
= ±75, ±310, ±625mAdc
I
OUT
= ±75, ±250, ±500mAdc
(main)
ART2812(dual)
ART2815(dual)
Group A
Subgroups
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
4, 5, 6
1
2, 3
1, 2, 3
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
MIN
4.95
±11.70
±14.50
3.0
150
75
4.8
±11.1
±14.0
MAX
5.05
±12.30
±15.15
30
3000
500
5.2
±12.9
±15.8
250
8.0
70
100
Units
V
Output power
Note 1
Output current
Note 1
Output regulation
Note 4
P
OUT
I
OUT
W
mA
(dual)
(main)
2812(dual)
2815(dual)
VR
V
Input current
Output ripple
Note 2
Input ripple
Note 2
Switching frequency
Efficiency
Power dissipation,
load fault
Output response to step
load changes
Notes 3, 5
Recovery time from step
load changes
Notes 5, 6
I
IN
V
RIP
I
RIP
F
S
Eff
P
D
I
OUT
= minimum rated, Pin 3 open
Pin 3 shorted to pin 2 (disabled)
V
IN
= 19 V, 28V, 50 V
I
OUT
= 3000mA main, ±500mA dual
V
IN
= 19 V, 28V, 50 V
I
OUT
= 3000mA main, ±500mA dual
Synchronization pin (pin 6) open
I
OUT
= 3000mA main, ±500mA dual
Short circuit, any output
10% Load to/from 50% load
50% Load to/from 100% load
10% Load to/from 50% load
mA
mV
P-P
mA
P-P
KHz
%
225
83
81
275
16
-200
-200
200
200
200
200
100
500
5.0
100
20
W
V
TL
mV
PK
T
TL
50% Load to/from 100% load
(main)
I
OUT
= minimum and full rated
I
OUT
= minimum and full rated
500VDC Input to output or any pin to case
(except pin 12)
µS
4, 5, 6
4, 5, 6
4, 5, 6
1
Turn on overshoot
Turn on delay
Note 7
Isolation
V
OS
T
DLY
ISO
(dual)
mV
mS
MΩ
Notes to Group A Test Table
1.
2.
3.
4.
5.
6.
7.
8.
Parameter verified during dynamic load regulation tests.
Guaranteed for DC to 20 MHz bandwidth. Test conducted using a 20KHz to 2MHz bandwidth.
Load current is stepped for output under test while other outputs are fixed at half rated load.
Each output is measured for all combinations of line and load. Only the minimum and maximum readings for each output are recorded.
Load step transition time
≥
10µS.
Recovery time is measured from the initiation of the transient to where V
OUT
has returned to within ±1% of its steady state value.
Turn on delay time is tested by application of a logical low to high transition on the enable pin (pin 3) with power present at the input.
Subgroups 1 and 4 are performed at +25ºC, subgroups 2 and 5 at -55ºC and subgroups 3 and 6 at +125ºC.
4
www.irf.com
ART28XXT Series
Radiation Performance
The radiation tolerance characteristics inherent in the
ART28XXT converter are the direct result of a carefully
planned ground-up design program with specific radiation
design goals. After identification of the general circuit
topology, a primary task of the design effort was selection
of appropriate elements from the list of devices for which
extensive radiation effects data was available. By imposing
sufficiently large margins on those electrical parameters
subject to the degrading effects of radiation, designers
were able to select appropriate elements for incorporation
into the circuit. Known radiation data was utilized for input
to PSPICE and RadSPICE in the generation of circuit
There is a small piece of extra copper between the two pads on the left. The middle is very thin and cannot be removed, but there is none on the right....
Does anyone know how to use two 555s to form a 556? How are the pins connected? What are the components around the 556 in the circuit below used for? How does the 556 work? I hope someone can give me ...
My project is based on WCE embedded system. The generated nk.nb0 is burned into it through the serial port. There are two different situations. One is to directly enter the .exe interface generated by...
I wrote a program in Keil software, and the compilation and connection are good through this software, without errors or warnings. But when I put it into the simulator software, there are errors when ...
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
Every time I go home and walk up the stairs, I am always scared. The corridor lights are often broken, and no one changes the bulbs, or they are not smart enough and need to be operated manually. E...[Details]
The capacity of a battery depends on the amount of charge and discharge, in addition to some factors of the battery itself. Obviously, if the charge and discharge of the battery can be recorded all...[Details]
Features
POE technology can ensure the safety of existing structured cabling while ensuring the normal operation of the existing network and minimizing costs. The IEEE 802.3af standard is ...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
Current
measurement:
Magnetic balance Hall current
sensor
is used
. The sensor can measure AC from DC to 100kHz.
In automatic measurement and control systems, it is often nec...[Details]
As a new type of centralized and decentralized elevator control system, serial communication has been widely used in China. Compared with the previous centralized and unified control system, each s...[Details]
Abstract: Based on the analysis of the characteristics of the IRIG-B (DC) code type, a design method for IRIG-B (DC) time code decoding is proposed. This method consists of a small number of periph...[Details]
Traditional synthesis techniques are increasingly unable to meet the needs of today's very large and complex FPGA designs implemented in 90nm and below process nodes. The problem is that traditio...[Details]
1. Introduction
Stepper motor is a basic component that converts electrical energy into kinetic energy. It has been widely used in a variety of electromechanical equipment, such as various machine...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
