TITLE
SPECIFICATION CONTROL DRAWING
FOUR CONDUCTOR CABLE, FLAT BRAID SHIELDED,
JACKETED, GENERAL PURPOSE, 600 VOLT
Date
Revision
44A214X
D
12-10-08
This specification sheet forms a part of the latest issue of Raychem Specification 44.
COMPONENT WIRES - 44A011X
SHIELD - TIN-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED PVDF
TABLE I. CABLE CONSTRUCTION DETAILS
PART NUMBER
1/
44A214X-26-*
44A214X-24-*
44A214X-22-*
44A214X-20-*
44A214X-18-*
44A214X-16-*
44A214X-14-*
44A214X-12-*
CONDUCTOR
SIZE
(AWG)
26
24
22
20
18
16
14
12
SHIELD STRAND
THICKNESS
(± .0004 inch)
.0015
.0015
.0015
.0015
.0015
.0015
.0015
.0015
JACKET THICKNESS
(in.)
MINIMUM
.006
.006
.006
.006
.007
.007
.007
.008
NOMINAL
.008
.008
.008
.008
.009
.009
.009
.010
OUTSIDE DIAMETER
(in.)
NOMINAL
.105
.120
.137
.156
.182
.199
.240
.288
MAXIMUM
.122
.140
.160
.183
.214
.234
.283
.340
MAXIMUM
WEIGHT
(lbs/1000 ft.)
10.3
13.8
18.8
25.9
37.4
46.0
68.6
104.
TABLE II. CABLE PERFORMANCE DETAILS
BEND TESTING
PART NUMBER
1/
MANDREL DIAMETER
(inch) (±3%)
LIFE CYCLE, IMMERSION
AND ACCELERATED AGING
3.00
3.00
6.00
6.00
6.00
6.00
6.00
10.0
COLD
BEND
3.00
3.00
6.00
6.00
6.00
6.00
6.00
10.0
WEIGHT
(lb) (±3%)
LIFE CYCLE, IMMERSION
AND ACCELERATED AGING
.500
.750
.750
.750
1.00
1.00
2.00
2.00
COLD
BEND
3.00
3.00
6.00
6.00
6.00
6.00
18.0
18.0
44A214X-26-*
44A214X-24-*
44A214X-22-*
44A214X-20-*
44A214X-18-*
44A214X-16-*
44A214X-14-*
44A214X-12-*
NOTE: Nominal values are for information only.
Nominal values are not requirements.
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/
COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
The TE logo, Tyco Electronics and Raychem are trademarks.
Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
© 2008 Tyco Electronics Corporation. All rights reserved.
Page 1 of 2
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
Revision
SCD
SPECIFICATION CONTROL DRAWING
Page 2 of 2
D
44A214X
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
ACCELERATED AGING: 300 ± 3°C for 6 hours
BLOCKING: 150 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute
FLAMMABILITY:
30 seconds (maximum); 3 in. (maximum); no flaming of facial tissue
IMMERSION: Diameter increase 5% (maximum),
no cracking, no dielectric breakdown
JACKET COLOR: White preferred
JACKET CONCENTRICITY: 70% (minimum)
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 200% (minimum)
Tensile Strength, 4000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1.5 kV (rms)
Impulse Dielectric Test, 6.0 kV (peak)
LIFE CYCLE: 200 ± 3°C for 168 hours
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
SHIELD COVERAGE: 90% (minimum)
VOLTAGE WITHSTAND (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The “X” in the part numbers on page 1 shall be replaced by the
applicable conductor material designator as follows:
1 tin-coated copper
2 silver-coated copper
3 nickel-coated copper
4 silver-coated high strength copper alloy (AWG's 26 -16 only)
The "*" in the part numbers above and on page 1 shall be replaced by color code designators with a slash separating
the component wire colors and a dash separating the component wire colors from the jacket color. Colors shown do not
necessarily reflect the sequence of manufacturing.
1/
Example: AWG 20, tin-coated copper wires, black, brown, red and
orange component wires; white jacket:
44A2141-20-0/1/2/3-9
1/
See footer section on page 1
京公网安备 11010802033920号
EEWORLD
