E-, I-Grades ....................................... –40°C to 125°C
H-Grade ............................................. –40°C to 150°C
MP-Grade .......................................... –55°C to 150°C
Storage Temperature Range .................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
M, ST Packages Only ........................................ 300°C
PIN CONFIGURATION
TOP VIEW
FRONT VIEW
OUT 1
OUT 2
OUT 3
SET 4
9
OUT
8
7
6
5
IN
IN
NC
NC
TAB IS
OUT
3
2
1
IN
OUT
SET
TAB IS
OUT
FRONT VIEW
3
2
1
M PACKAGE
3-LEAD PLASTIC DD-PAK
T
JMAX
= 150°C,
θ
JA
= 14°C/W,
θ
JC
= 3°C/W
IN
OUT
SET
DD PACKAGE
8-LEAD (3mm
×
3mm) PLASTIC DFN
T
JMAX
= 150°C,
θ
JA
= 28°C/W,
θ
JC
= 5.3°C/W
EXPOSED PAD (PIN 9) IS OUT, MUST BE SOLDERED TO PCB
ST PACKAGE
3-LEAD PLASTIC SOT-223
T
JMAX
= 150°C,
θ
JA
= 25°C/W,
θ
JC
= 15°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT3088EDD#PBF
LT3088IDD#PBF
LT3088HDD#PBF
LT3088EST#PBF
LT3088IST#PBF
LT3088HST#PBF
LT3088MPST#PBF
LT3088EM#PBF
LT3088IM#PBF
LT3088HM#PBF
LT3088MPM#PBF
TAPE AND REEL
LT3088EDD#TRPBF
LT3088IDD#TRPBF
LT3088HDD#TRPBF
LT3088EST#TRPBF
LT3088IST#TRPBF
LT3088HST#TRPBF
LT3088MPST#TRPBF
LT3088EM#TRPBF
LT3088IM#TRPBF
LT3088HM#TRPBF
LT3088MPM#TRPBF
PART MARKING*
LGSZ
LGSZ
LGSZ
3088
3088
3088
3088
LT3088M
LT3088M
LT3088M
LT3088M
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic DD-Pak
3-Lead Plastic DD-Pak
3-Lead Plastic DD-Pak
3-Lead Plastic DD-Pak
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
2
3088fb
For more information
www.linear.com/LT3088
LT3088
ELECTRICAL CHARACTERISTICS
PARAMETER
SET Pin Current
Offset Voltage
(V
OUT
– V
SET
)
I
SET
Load Regulation
V
OS
Load Regulation
(Note 7)
Line Regulation
Minimum Load Current (Note 3)
Dropout Voltage (Note 4)
Current Limit
Reference Current RMS Output Noise (Note 5)
Error Amplifier RMS Output Noise (Note 5)
Ripple Rejection
V
RIPPLE
= 0.5V
P-P
, I
LOAD
= 0.1A, C
SET
= 0.1µF,
C
OUT
=10µF, V
IN
= V
OUT(NOMINAL)
+ 3V
Thermal Regulation, I
SET
∆I
LOAD
= 2mA to 800mA
∆I
SET
∆V
OS
I
SET
V
OS
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C. (Note 2)
CONDITIONS
V
IN
= 2V, I
LOAD
= 2mA
2V ≤ V
IN
≤ 36V, 2mA ≤ I
LOAD
≤ 800mA
V
IN
= 2V, I
LOAD
= 2mA
V
IN
= 2V, I
LOAD
= 2mA
∆I
LOAD
= 2mA to 800mA
DD Package
M, ST Packages
∆V
IN
= 2V to 36V, I
LOAD
= 2mA
∆V
IN
= 2V to 36V, I
LOAD
= 2mA
2V ≤ V
IN
≤ 36V
I
LOAD
= 100mA
I
LOAD
= 800mA
V
IN
= 5V, V
SET
= 0V, V
OUT
= –0.1V
10Hz ≤ f ≤ 100kHz
I
LOAD
= 800mA, 10Hz ≤ f ≤ 100kHz,
C
OUT
= 0µF, C
SET
= 0.1µF
f = 120Hz
f = 10kHz
f = 1MHz
10ms Pulse
75
l
l
l
l
l
l
l
MIN
49.5
49
–1.5
–3.5
TYP
50
50
0
0
–0.1
–0.5
–1.5
1.5
0.001
0.4
1.21
1.35
MAX
50.5
51
1.5
3.5
–3
–4
UNITS
µA
µA
mV
mV
nA
mV
mV
nA/V
mV/V
2
1.6
mA
V
V
A
nA
RMS
µV
RMS
dB
dB
dB
%/W
0.8
1.2
5.7
27
90
75
20
0.003
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Unless otherwise specified, all voltages are with respect to V
OUT
.
The LT3088 is tested and specified under pulse load conditions such
that T
J
≈ T
A
. The LT3088E is tested at T
A
= 25°C and performance is
guaranteed from 0°C to 125°C. Performance of the LT3088E over the
full –40°C and 125°C operating temperature range is assured by design,
characterization, and correlation with statistical process controls. The
LT3088I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT3088MP is 100% tested and guaranteed
over the –55°C to 150°C operating junction temperature range. The
LT3088H is tested at 150°C operating junction temperature. High junction
temperatures degrade operating lifetimes. Operating lifetime is degraded at
junction temperatures greater than 125°C.
Note 3:
Minimum load current is equivalent to the quiescent current of
the part. Since all quiescent and drive current is delivered to the output
of the part, the minimum load current is the minimum current required to
maintain regulation.
Note 4:
For the LT3088, dropout is specified as the minimum input-to-
output voltage differential required supplying a given output current.
Note 5:
Adding a small capacitor across the reference current resistor
lowers output noise. Adding this capacitor bypasses the resistor shot
noise and reference current noise; output noise is then equal to error
amplifier noise (see Applications Information section).
Note 6:
Diodes with series 400Ω resistors clamp the SET pin to the
OUT pin. These diodes and resistors only carry current under transient
overloads. During normal operation, keep the OUT-to-SET differential
voltage below 2V.
Note 7:
Load regulation is Kelvin sensed at the package.
Note 8:
This IC includes overtemperature protection that protects the
device during momentary overload conditions. Junction temperature
exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
Power supply design tip 1: Choose the correct operating frequency for your power supply
By Robert Kollman Texas InstrumentsWelcome to Power Design Tips! With today's emphasis on more efficient, lower ...
Electromagnetic waves are arranged in descending order according to wavelength: radio waves, infrared rays, visible light, ultraviolet rays, X-rays, and gamma rays. The following are several common el...
Use WEBENCH to design the lowest cost circuit design for solar cell step-down. The total BOM cost is $1.21 and the efficiency is 92%. The overall situation is good. Finally, upload the entire design d...
Ask a question about downloading the image: Using dnw5.0, PB4.2, ARM2440 board, can't broadcast Ethernet Boot Loader Configuration: --------------------------------------- 1) IP address: 192.168.1.123...
To enable real-time monitoring of home security and automatically dial a number for voice prompts or send text messages when an alarm occurs, a GPRS-based embedded telephone alarm system was design...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
Capable of providing precise and efficient thermal management for artificial intelligence computing power, intelligent sensing and autonomous driving systems
Shenzhen, ...[Details]
Recently, AstroBo Robot, a subsidiary of Chenxing Automation, launched a new mobile collaborative palletizing product. Leveraging an omnidirectional mobile chassis, an intelligent scheduling system...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
In June 2014, the Ministry of Industry and Information Technology issued 4G FD-LTE licenses to China Unicom and China Telecom. Together with the 4G TD-LTE licenses issued to China Mobile, China Uni...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
Analog Devices held a third-quarter fiscal 2025 earnings conference call. Vincent T. Roche, CEO and Chairman of the Board, and Richard C. Puccio, Executive Vice President and Chief Financial Office...[Details]
introduction
Inverter air conditioners are a trend in the current era and have gradually become commonplace in countless households. Beyond their basic cooling and heating functions, air condi...[Details]
The evolution of high-speed networks remains guided by the same core objectives: increasing data rates, reducing latency, improving reliability, lowering power consumption, and maintaining or exten...[Details]
I believe everyone has heard of memory. If your computer is slow, your experts may recommend upgrading it to a larger capacity. But what exactly is computer memory used for? Why does memory capacit...[Details]
Silicon Labs (also known as "Silicon Labs"), an innovative leader in low-power wireless connectivity, will showcase its cutting-edge artificial intelligence (AI) and Internet of Things (IoT) solu...[Details]
Currently, PLCs are widely used in various industries, including special machine tools, machine tools, control systems, building automation, steel, petrochemicals, electricity, building materials, ...[Details]
Perhaps due to the stereotypes surrounding electronic products, many owners of pure electric vehicles have questions about charging. What's the correct way to charge? How can charging slow down bat...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
