CRCW06035K60FKEAC datasheet, PDF

Suppliers	Part Number	Price	MOQ	In stock
	CRCW06035K60FKEAC	-	-	View	Buy Now

CRCW...C e3

www.vishay.com

Vishay

Lead (Pb)-free Thick Film, Rectangular

Commodity Chip Resistors

FEATURES

• High volume product suitable for commercial

applications

• Stability (R/R



1 % for 1000 h at

70 °C)

• Lead (Pb)-free solder contacts on Ni barrier

layer

• Metal glaze on ceramic

• Material categorization: for definitions of compliance

please see

www.vishay.com/doc?99912

STANDARD ELECTRICAL SPECIFICATIONS

MODEL

CASE

SIZE

INCH

CASE

SIZE

METRIC

POWER RATING

P

70 °C

W

0.063

LIMITING

ELEMENT

VOLTAGE

MAX. V



50

TEMPERATURE

COEFFICIENT

ppm/K

± 100

± 200

TOLERANCE

%

±1

±5

RESISTANCE

RANGE



1R0 to 10M

E-SERIES

E24; E96

E24

CRCW0402...C

0402

RR 1005M

Zero-Ohm-Resistor:

R

max.

= 20 m,

I

max.

at 70 °C = 1.5 A

0.10

75

± 100

± 200

±1

±5

1R0 to 10M

E24; E96

E24

CRCW0603...C

0603

RR 1608M

Zero-Ohm-Resistor:

R

max.

= 20 m,

I

max.

at 70 °C = 2.0 A

0.125

150

± 100

± 200

±1

±5

1R0 to 10M

E24; E96

E24

CRCW0805...C

0805

RR 2012M

Zero-Ohm-Resistor:

R

max.

= 20 m,

I

max.

at 70 °C = 2.5 A

0.25

200

± 100

± 200

±1

±5

1R0 to 10M

E24; E96

E24

CRCW1206...C

1206

RR 3216M

Zero-Ohm-Resistor:

R

max.

= 20 m,

I

max.

at 70 °C = 3.5 A

Notes

• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over

operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime

• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material

TECHNICAL SPECIFICATIONS

PARAMETER

Rated dissipation at 70°C

(1)

Limiting element voltage

U

max.

AC/DC

Insulation voltage

U

ins.

(1 min)

Insulation resistance

Category temperature range

Failure rate

Weight/1000 pieces

UNIT

W

V



°C

h

-1

g

0.65

2

CRCW0402...C

0.063

50

> 75

CRCW0603...C

0.10

75

> 100

> 10

9

- 55 to + 155

0.1 x 10

-9

5.5

10

CRCW0805...C

0.125

150

> 200

CRCW1206...C

0.25

200

> 300

Note

(1)

The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded

Revision: 02-Nov-17

Document Number: 28773

1

For technical questions, contact:

ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

www.vishay.com/doc?91000

CRCW...C e3

www.vishay.com

Vishay

PART NUMBER AND PRODUCT DESCRIPTION

PART NUMBER: CRCW0603562RFKECC

C

R

C

W

0

6

0

3

5

6

2

TCR

R

F

K

E

C

SPECIAL

Up to 2 digits

C

= commodity

MODEL/SIZE

CRCW0402

CRCW0603

CRCW0805

CRCW1206

VALUE

R

= decimal

K

= thousand

M

= million

0000

= jumper

TOLERANCE

F

= ± 1.0 %

J

= ± 5.0 %

Z

= jumper

PACKAGING

EA, EB,

EC, ED,

EE

K

= ± 100 ppm/K

N

= ± 200 ppm/K

0

= jumper

PRODUCT DESCRIPTION: CRCW0603-C 100 562R 1 % ET6 E3

CRCW0603-C

MODEL

CRCW0402-C

CRCW0603-C

CRCW0805-C

CRCW1206-C

100

TCR

± 200

ppm/K

± 100

ppm/K

562R

RESISTANCE

VALUE

10R

= 10



562R

= 562



10K

= 10.0 k

1M

= 1 M

0R0

= jumper

1%

TOLERANCE

±

5%

±

1%

ET6

PACKAGING

ET1, ET5,

ET6, ET7,

EF4

e3

LEAD (Pb)-FREE

e3

= pure tin

termination

finish

PACKAGING

TYPE / SIZE

CRCW0402…C

CODE

ED = ET7

EE = EF4

EA = ET1

EB = ET5

EC = ET6

EA = ET1

EB = ET5

EC = ET6

EA = ET1

EB = ET5

EC = ET6

QUANTITY

10 000

50 000

5000

10 000

20 000

5000

10 000

20 000

5000

10 000

20 000

PACKAGING STYLE

WIDTH

PITCH

2 mm

PACKAGING

DIMENSIONS

Ø 180 mm/7"

Ø 330 mm/13"

Ø 180 mm/7"

Ø 254 mm/10"

Ø 330 mm/13"

Ø 180 mm/7"

Ø 254 mm/10"

Ø 330 mm/13"

Ø 180 mm/7"

Ø 254 mm/10"

Ø 330 mm/13"

CRCW0603…C

4 mm

Paper tape acc. to

IEC 60286-3, Type 1a

8 mm

4 mm

CRCW0805…C

CRCW1206…C

4 mm

DIMENSIONS

SIZE

INCH METRIC

0402

1005

0603

1608

0805

2012

1206

3216

L

1.0 ± 0.10

1.60 ± 0.10

2.0 ± 0.10

3.05 ± 0.10

DIMENSIONS

(in millimeters)

W

0.5 ± 0.05

0.80 ± 0.10

1.25 ± 0.15

1.55 ± 0.10

H

T1

0.30 ± 0.05 0.25 ± 0.10

0.45 ± 0.10 0.3 ± 0.2

0.50 ± 0.10 0.35 ± 0.15

0.55

+ 0.10

- 0.05

T2

0.2 ± 0.1

0.3 ± 0.2

0.35 ± 0.2

0.45 ± 0.2

SOLDER PAD DIMENSIONS

(1)

(in millimeters)

REFLOW SOLDERING

WAVE SOLDERING

a

b

l

a

b

l

0.4

0.6

0.5

0.9

1.0

0.9

1.0

0.7

1.3

1.2

0.9

1.3

0.9

1.7

2.0

1.1

1.7

2.3

0.35 ± 0.15

Note

(1)

The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of

power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials maybe required to maintain

the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on board materials.

The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or

in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many

other parameters. Still the given solder pad dimensions will be found adequate for most general applications

Revision: 02-Nov-17

Document Number: 28773

2

For technical questions, contact:

ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

www.vishay.com/doc?91000

CRCW...C e3

www.vishay.com

FUNCTIONAL PERFORMANCE

Rated Power in %

120

100

Vishay

80

60

40

20

0

- 55

- 25

0

25

50

Derating

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC 60068-2

TEST

METHOD

75

100

125

155 175

70 Ambient Temperature in

°C

REQUIREMENTS PERMISSIBLE

CHANGE (R)

TEST

PROCEDURE

STABILITY

CLASS 1

OR BETTER

1



to 10 M

±1%

± 100 ppm/K

STABILITY

CLASS 2

OR BETTER

1



to 10 M

±5%

± 200 ppm/K

Stability for product types:

CRCW...C e3

4.5

4.8.4.2

4.13

-

Resistance

Temperature

coefficient

Short time

overload

-

(20/- 55/20) °C and

(20/125/20) °C

U

= 2.5 x

P

70

x

R



2 x

U

max.;

5 s

Solder bath method;

Sn60Pb40

non activated flux;

(235 ± 5) °C

(2 ± 0.2) s

Solder bath method;

Sn96.5Ag3Cu0.5

non activated flux;

(245 ± 5) °C

(3 ± 0.3) s

± (2 %

R

+ 0.1

)

Good tinning ( 95 % covered)

no visible damage

4.17.5

58 (Td)

Solderability

Pre-aging

4 h at 155 °C,

dryheat

Good tinning ( 95 % covered)

no visible damage

4.18.2

4.19

58 (Td)

14 (Na)

Resistance to

soldering heat

Rapid change

of temperature

Damp heat,

steady state

Operation at low

temperature

Solder bath method

(260 ± 5) °C; (10 ± 1) s

30 min. at - 55 °C;

30 min. at 125 °C;

5 cycles

(40 ± 2) °C;

56 days;

(93 ± 3) % RH

-55 °C, 1 h

U

=

P

70

x

R



U

max.;

1.5 h on; 0.5 h off;

70 °C; 1000 h

70 °C; 8000 h

± (1%

R

+ 0.05

)

± (0.25 %

R

+ 0.05

)

± (0.5 %

R

+ 0.05

)

4.24

4.36

78 (Cab)

-

± (1 %

R

+ 0.05

)

± (2 %

R

+ 0.1

)

± (1 %

R

+ 0.05

)

4.25.1

-

Endurance

at 70 °C

± (1 %

R

+ 0.05

)

± (2 %

R

+ 0.1

)

± (1 %

R

+ 0.05

)

± (2 %

R

+ 0.1

)

± (4 %

R

+ 0.1

)

± (2 %

R

+ 0.1

)

4.25.3

-

Endurance at

upper category

temperature

155 °C, 1000 h

Revision: 02-Nov-17

Document Number: 28773

3

For technical questions, contact:

ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

www.vishay.com/doc?91000

CRCW...C e3

www.vishay.com

Vishay

APPLICABLE SPECIFICATIONS

• EN 60115-1

• EN 140400

• EN 140401-802

• IEC 60068-2-X

• IEC 60286-3

Generic specification

Sectional specification

Detail specification

Variety of environmental test procedures

Packaging of SMD components

Revision: 02-Nov-17

Document Number: 28773

4

For technical questions, contact:

ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT

www.vishay.com/doc?91000

Legal Disclaimer Notice

www.vishay.com

Vishay

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Revision: 08-Feb-17

1

Document Number: 91000

Parameter Name	Attribute value
resistance	5.6 kOhms
Tolerance	±1%
Power (W)	0.1W，1/10W
component	thick film
characteristic	-
Temperature Coefficient	±100ppm/°C
Operating temperature	-55°C ~ 155°C
Package/casing	0603 (1608 Metric)
Supplier device packaging	603
size/dimensions	0.063" long x 0.032" wide (1.60mm x 0.80mm)
Height - Installation (maximum)	0.022"（0.55mm）
Number of terminals	2
failure rate	-

CRCW06035K60FKEAC

CRCW06035K60FKEAC Online Shopping

CRCW06035K60FKEAC Overview

CRCW06035K60FKEAC Parametric

Preview

Recommended Resources