EEWORLDEEWORLDEEWORLD

Part Number

Search

8552J82ZBE1

Description
OCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT
Categorysemiconductor    Analog mixed-signal IC   
File Size359KB,5 Pages
ManufacturerITT
Websitehttp://www.ittcannon.com/
Download Datasheet Parametric View All

8552J82ZBE1 Overview

OCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT

8552J82ZBE1 Parametric

Parameter NameAttribute value
Maximum operating temperature70 Cel
Minimum operating temperature0.0 Cel
Maximum supply voltage3.46 V
Minimum supply voltage3.14 V
Rated supply voltage3.3 V
Rated operating frequency12.8 MHz
stateACTIVE
terminal coatingNOT SPECIFIED
Installation featuresThrough hole mounting
DimensionsL25.7XB25.7XH13.2 (mm)/L1.012XB1.012XH0.52 (inch)
Ageing4 PPM/20 YEAR
Frequency converter0
frequency stable voltage0.0020 ppm
input power1.25 W
Manufacturer Series760
Vibration typeHCMOS
Industrial supply voltage3.3V
Heating power5 W
C&K 8500 Series
Subminiature Pushbutton Switches
A
Pushbutton
Features/Benefits
Pre-travel or over-travel models
available
Ratings up to 3 AMPS
Reliable contact design
RoHS compliant
Typical Applications
Detection
Telecommunications and
networking equipment
Computers and peripherals
Models Available
Specifications
CONTACT RATING: Q contact material (853X Models): 1 AMP @
120 V AC or 28 V DC; (855X Models): 3 AMPS @ 120 V AC or
28 V DC. See page A-63 for additional ratings.
ELECTRICAL LIFE:
853X MODELS: 250,000 actuations at full load.
855X MODELS: 10,000 actuations at full load.
CONTACT RESISTANCE: Below 30 mΩ typ. initial @
2-4 V DC, 100 mA, for both silver and gold plated contacts.
INSULATION RESISTANCE: 109
min.
DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.
OPERATING TEMPERATURE: –30ºC to 65ºC.
NOTE:
Any models supplied with Q, B or G contact material are RoHS compliant. For the
latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs.
NOTE:
Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Materials
CASE: Glass filled phenolic or diallyl phthalate (DAP) (UL 94V-0).
PLUNGER: Phenolic or glass filled polyester, black standard(UL94V-0).
CAP & FRAME: Nylon, black, standard.
BUSHING: Brass, nickel plated.
CONTACTS: Q contact material: Coin silver, silver plated. See page
A-63 for additional contact materials.
TERMINALS: Q contact material: Copper alloy, silver plated. See page
A-63 for additional contact materials.
TERMINAL SEAL: Epoxy.
HARDWARE: Nut: Brass, nickel plated; Lockwasher: Steel, bright
nickel plated.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown
and described on pages A-61 thru A-64. For additional options not shown in catalog, consult Customer Service Center. All
models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods.
Switch Function
8531
SPST Off-Mom. 1 Amp
8532
SPST Off-Mom. 1 Amp
8533
SPST On-Mom. 1 Amp
8534
SPST On-Mom. 1 Amp
8551
SPST Off-Mom. 3 Amps
8552
SPST Off-Mom. 3 Amps
Actuator or Plunger
M
.150" high
J81
Snap-in with frame
J82
Snap-in with frame for LED
S
.210" high
T
15/32 bushing
T1
15/32 bushing with frame
(8532 and 8534 only)
Terminations
Z
Solder lug
AV
Right angle, PC thru-hole
C
PC Thru-hole
Contact Material
Q
Silver
B
Gold
Seal
G
Gold over silver
E
Epoxy
D
No epoxy seal
Cap or Plunger Color
2
Black
1
White
Frame Color
3
Red
2
Black
9
Gray
NONE
Models without frame
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
A–60
www.ittcannon.com
Should I choose combinational logic or sequential logic?
The output of combinational logic is only related to the current input; while the output of sequential logic is not only related to the input, but also to the previous state of the system. This is ver...
DSP16 FPGA/CPLD
PG-1000 Series Pulse Generator SCPI Remote Control
This article uses the PG 1000 series pulse generator from Active Technologies (AT) as an example to explain how to use NI MAX to configure the system before using SCPI to control the instrument. 1.[/c...
Stone_Mei Test/Measurement
How to test if the TVS diode is working
I don't have any tools like an electrostatic generator, only a linear power supply with a maximum of 60V 3.3A. A smaj36 transient tube is connected in parallel to the circuit, but I don't know if this...
abusama Industrial Control Electronics
AVR STUDIO4 compiles 485 sending program and there is a puzzling problem. Please help me find out what is going on.
Program: void USART1_Send(void) //RS485 sending function { uint i; // uchar tx_cBuffer1[100]; tx_cBuffer1[0]=0x01; tx_cBuffer1[1]=0x03; tx_cBuffer1[2]=0x00; tx_cBuffer1[3]=0x03; tx_cBuffer1[4]=0x00; t...
weipj528 Microchip MCU
Classification and application of measuring instruments
1. Oscilloscope An oscilloscope is an electronic instrument for measuring voltage waveforms. It can display the law of the measured voltage signal changing over time in a graphical way. Using an oscil...
vini Test/Measurement
FPGA Flowing Light
Using FPGA to run the program of running water lamp may be useful to you!...
jjkwz FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 75  2786  1578  2227  1829  2  57  32  45  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号