EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
UD PACKAGE
16-LEAD (3mm
×
3mm) PLASTIC QFN
T
JMAX
= 125°C,
θ
JA
= 68°C/W,
θ
JC
= 4.2°C/W
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
orDer inForMaTion
LEAD FREE FINISH
LTC3851AEMSE-1#PBF
LTC3851AIMSE-1#PBF
LTC3851AHMSE-1#PBF
LTC3851AMPMSE-1#PBF
LTC3851AEUD-1#PBF
LTC3851AIUD-1#PBF
TAPE AND REEL
LTC3851AEMSE-1#TRPBF
LTC3851AIMSE-1#TRPBF
LTC3851AHMSE-1#TRPBF
LTC3851AMPMSE-1#TRPBF
LTC3851AEUD-1#TRPBF
LTC3851AIUD-1#TRPBF
PART MARKING*
3851A1
3851A1
3851A1
3851A1
LFQB
LFQB
PACKAGE DESCRIPTION
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead (3mm
×
3mm) Plastic QFN
16-Lead (3mm
×
3mm) Plastic QFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
TG
TOP VIEW
3851a1fa
2
LTC3851A-1
elecTrical characTerisTics
SYMBOL
V
IN
V
FB
PARAMETER
Input Operating Voltage Range
Regulated Feedback Voltage
I
TH
= 1.2V (Note 4) 0°C to 85°C
I
TH
= 1.2V (Note 4) –40°C to 125°C
I
TH
= 1.2V (Note 4) –40°C to 150°C
I
TH
= 1.2V (Note 4) –55°C to 150°C
(Note 4)
V
IN
= 6V to 38V (Note 4)
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 0.7V
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 0.7V (H-Grade, MP-Grade)
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 1.6V
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 1.6V (H-Grade, MP-Grade)
g
m
g
m
GBW
I
Q
UVLO
UVLO Hys
I
SENSE
I
TK/SS
V
RUN
V
RUNHYS
V
SENSE(MAX)
TG R
UP
TG R
DOWN
BG R
UP
BG R
DOWN
TG t
r
TG t
f
BG tr
BG tf
TG/BG t
1D
BG/TG t
2D
t
ON(MIN)
V
INTVCC
V
LDO
INT
Transconductance Amplifier g
m
Transconductance Amp Gain Bandwidth
Input DC Supply Current
Normal Mode
Shutdown
Undervoltage Lockout on INTV
CC
UVLO Hysteresis
SENSE Pins Current
Soft-Start Charge Current
RUN Pin On—Threshold
RUN Pin On—Hysteresis
Maximum Current Sense Threshold
TG Driver Pull-Up On-Resistance
TG Driver Pull-Down On-Resistance
BG Driver Pull-Up On-Resistance
BG Driver Pull-Down On-Resistance
TG Transition Time
Rise Time
Fall Time
BG Transition Time
Rise Time
Fall Time
Top Gate Off to Bottom Gate On Delay
Bottom Switch-On Delay Time
Bottom Gate Off to Top Gate On Delay
Top Switch-On Delay Time
Minimum On-Time
Internal V
CC
Voltage
INTV
CC
Load Regulation
V
FB
= 0.7V, V
SENSE
= 3.3V
V
FB
= 0.7V, V
SENSE
= 3.3V (H-Grade, MP-Grade)
TG High
TG Low
BG High
BG Low
(Note 6)
C
LOAD
= 3300pF
C
LOAD
= 3300pF
(Note 6)
C
LOAD
= 3300pF
C
LOAD
= 3300pF
C
LOAD
= 3300pF Each Driver
(Note 6)
C
LOAD
= 3300pF Each Driver
(Note 6)
(Note 7)
6V < V
IN
< 38V
I
CC
= 0mA to 50mA
4.8
l
l
l
l
l
l
l
l
l
l
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C (Note 2). V
IN
= 15V, V
RUN
= 5V unless otherwise noted.
CONDITIONS
MIN
4
0.792
0.788
0.788
0.788
0.800
TYP
MAX
38
0.808
0.812
0.812
0.812
–50
0.02
0.1
0.2
–0.01
–0.1
–0.2
2
3
1
25
3.25
0.4
±1
V
TK/SS
= 0V
V
RUN
Rising
l
UNITS
V
V
V
V
V
nA
%/V
%
%
%
%
mmho
MHz
mA
µA
V
V
Main Control Loops
I
FB
V
REFLNREG
V
LOADREG
Feedback Current
Reference Voltage Line Regulation
Output Voltage Load Regulation
–10
0.002
0.01
I
TH
= 1.2V, Sink/Source = 5µA (Note 4)
I
TH
= 1.2V (Note 8)
(Note 5)
V
RUN
= 5V
V
RUN
= 0V
V
INTVCC
Ramping Down
50
±2
2
1.35
65
70
µA
µA
V
mV
mV
mV
Ω
Ω
Ω
Ω
ns
ns
ns
ns
ns
ns
ns
0.6
1.10
40
35
1
1.22
120
53
2.2
1.2
2.1
1.1
25
25
25
25
30
30
90
5
0.5
INTV
CC
Linear Regulator
5.2
V
%
3851a1fa
3
LTC3851A-1
elecTrical characTerisTics
SYMBOL
f
NOM
f
LOW
f
HIGH
R
MODE/PLLIN
f
MODE
I
FREQ
PGOOD Output
V
PGL
I
PGOOD
V
PG
PGOOD Voltage Low
PGOOD Leakage Current
PGOOD Trip Level
I
PGOOD
= 2mA
V
PGOOD
= 5V
V
FB
with Respect to Set Regulated Voltage
V
FB
Ramping Negative (UV)
V
FB
Ramping Positive (OV)
–12.5
7.5
–10
10
0.1
0.3
±1
–7.5
12.5
V
µA
%
%
PARAMETER
Nominal Frequency
Lowest Frequency
Highest Frequency
MODE/PLLIN Input Resistance
MODE/PLLIN Minimum Input Frequency V
MODE
= External Clock
MODE/PLLIN Maximum Input Frequency V
MODE
= External Clock
Phase Detector Output Current
Sinking Capability
Sourcing Capability
f
MODE
> f
OSC
f
MODE
< f
OSC
Oscillator and Phase-Locked Loop
R
FREQ
= 60k
R
FREQ
= 160k
R
FREQ
= 36k
460
205
690
500
235
750
100
250
750
–90
75
540
265
810
kHz
kHz
kHz
kΩ
kHz
kHz
µA
µA
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C (Note 2). V
IN
= 15V, V
RUN
= 5V unless otherwise noted.
CONDITIONS
MIN
TYP
MAX
UNITS
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LTC3851A-1 is tested under pulsed load conditions such that
T
A
≈ T
J
. The LTC3851AE-1 is guaranteed to meet performance
specifications from 0°C to 85°C junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LTC3851AI-1 is guaranteed to meet specifications over the –40°C
to 125°C operating junction temperature range, the LTC3851AH-1 is
guaranteed over the –40°C to 150°C operating junction temperature range
and the LTC3851AMP-1 is tested and guaranteed over the –55°C to 150°C
operating junction temperature range. High junction temperatures degrade
operating lifetimes; operating lifetime is derated for junction temperatures
greater than 125°C. Note that the maximum ambient temperature
consistent with these specifications is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
impedance and other environmental factors.
Note 3:
T
J
is calculated from the ambient temperature T
A
and power
dissipation P
D
according to the following formulas:
LTC3851AMSE-1: T
J
= T
A
+ (P
D
• 40°C/W)
LTC3851AUD-1: T
J
= T
A
+ (P
D
• 68°C/W)
Note 4:
The LTC3851A-1 is tested in a feedback loop that servos V
ITH
to a
specified voltage and measures the resultant V
FB
.
Note 5:
Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
Note 6:
Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels. Rise and fall times are assured by
design, characterization and correlation with statistical process controls.
Note 7:
The minimum on-time condition is specified for an inductor
peak-to-peak ripple current ~40% of I
MAX
(see Minimum On-Time
Considerations in the Applications Information section).
[i=s]This post was last edited by slotg on 2016-3-23 23:36[/i] After seeing the introduction of MicroPython on the forum, I have been thinking about what can be done with such a platform. When searchi...
Hello fellow experts:My current system architecture is that the external signal is transmitted to the PC through the "signal interception card" to MATLAB for calculation and processing and then output...
I am using MSP430F135 to build a project, but XT2 is not used. How can I properly handle the XT2IN and XT2OUT pins?Can I connect XT2IN to ground and leave XT2OUT floating?...
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
A scale, a large, ground-mounted scale, is typically used to measure the tonnage of truck cargo. It's the primary weighing device used in factories, mines, and businesses for bulk cargo measurement...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Hair dryer structure and working principle: It is mainly used for drying and shaping hair, but it can also be used for local drying, heating and treatment in laboratories, physiotherapy rooms, ind...[Details]
introduction
The OMAP-L138 dual-core processor is a new generation of low-power single-chip systems (SoCs) from TI. It is widely used in communications, industrial, medical diagnostic, and aud...[Details]
In microwave amplification circuits, the power chip is the core of the entire circuit. A large number of semiconductor devices in the chip will generate a lot of heat when working. If the heat diss...[Details]
With the continuous development of ultrasonic technology, ultrasound has been widely used in fields such as inspection, cleaning, welding, and medical treatment, and has even found its way into tex...[Details]
In recent years, with the development of MOSFETs, they have gradually replaced transistors in the low-power, fast-switching industry. Major manufacturers in this field have also been reducing their...[Details]
Electronic devices are small individual components in electronic circuits. Transistors are common electronic components. Because of their wide range of applications, according to the usage of the e...[Details]
In July 2025, stimulated by the "old for new" policy, China's new energy vehicle penetration rate reached a historic 50% mark. While industry experts like Cui Dongshu celebrated the market's perfor...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
