E-, I-Grades ....................................... –40°C to 125°C
H-Grade ............................................. –40°C to 150°C
MP-Grade .......................................... –55°C to 150°C
Storage Temperature Range .................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
M, ST Packages Only ........................................ 300°C
PIN CONFIGURATION
TOP VIEW
FRONT VIEW
OUT 1
OUT 2
OUT 3
SET 4
9
OUT
8
7
6
5
IN
IN
NC
NC
TAB IS
OUT
3
2
1
IN
OUT
SET
TAB IS
OUT
FRONT VIEW
3
2
1
M PACKAGE
3-LEAD PLASTIC DD-PAK
T
JMAX
= 150°C,
θ
JA
= 14°C/W,
θ
JC
= 3°C/W
IN
OUT
SET
DD PACKAGE
8-LEAD (3mm
×
3mm) PLASTIC DFN
T
JMAX
= 150°C,
θ
JA
= 28°C/W,
θ
JC
= 5.3°C/W
EXPOSED PAD (PIN 9) IS OUT, MUST BE SOLDERED TO PCB
ST PACKAGE
3-LEAD PLASTIC SOT-223
T
JMAX
= 150°C,
θ
JA
= 25°C/W,
θ
JC
= 15°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT3088EDD#PBF
LT3088IDD#PBF
LT3088HDD#PBF
LT3088EST#PBF
LT3088IST#PBF
LT3088HST#PBF
LT3088MPST#PBF
LT3088EM#PBF
LT3088IM#PBF
LT3088HM#PBF
LT3088MPM#PBF
TAPE AND REEL
LT3088EDD#TRPBF
LT3088IDD#TRPBF
LT3088HDD#TRPBF
LT3088EST#TRPBF
LT3088IST#TRPBF
LT3088HST#TRPBF
LT3088MPST#TRPBF
LT3088EM#TRPBF
LT3088IM#TRPBF
LT3088HM#TRPBF
LT3088MPM#TRPBF
PART MARKING*
LGSZ
LGSZ
LGSZ
3088
3088
3088
3088
LT3088M
LT3088M
LT3088M
LT3088M
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic DD-Pak
3-Lead Plastic DD-Pak
3-Lead Plastic DD-Pak
3-Lead Plastic DD-Pak
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/.
Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
2
3088fb
For more information
www.linear.com/LT3088
LT3088
ELECTRICAL CHARACTERISTICS
PARAMETER
SET Pin Current
Offset Voltage
(V
OUT
– V
SET
)
I
SET
Load Regulation
V
OS
Load Regulation
(Note 7)
Line Regulation
Minimum Load Current (Note 3)
Dropout Voltage (Note 4)
Current Limit
Reference Current RMS Output Noise (Note 5)
Error Amplifier RMS Output Noise (Note 5)
Ripple Rejection
V
RIPPLE
= 0.5V
P-P
, I
LOAD
= 0.1A, C
SET
= 0.1µF,
C
OUT
=10µF, V
IN
= V
OUT(NOMINAL)
+ 3V
Thermal Regulation, I
SET
∆I
LOAD
= 2mA to 800mA
∆I
SET
∆V
OS
I
SET
V
OS
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C. (Note 2)
CONDITIONS
V
IN
= 2V, I
LOAD
= 2mA
2V ≤ V
IN
≤ 36V, 2mA ≤ I
LOAD
≤ 800mA
V
IN
= 2V, I
LOAD
= 2mA
V
IN
= 2V, I
LOAD
= 2mA
∆I
LOAD
= 2mA to 800mA
DD Package
M, ST Packages
∆V
IN
= 2V to 36V, I
LOAD
= 2mA
∆V
IN
= 2V to 36V, I
LOAD
= 2mA
2V ≤ V
IN
≤ 36V
I
LOAD
= 100mA
I
LOAD
= 800mA
V
IN
= 5V, V
SET
= 0V, V
OUT
= –0.1V
10Hz ≤ f ≤ 100kHz
I
LOAD
= 800mA, 10Hz ≤ f ≤ 100kHz,
C
OUT
= 0µF, C
SET
= 0.1µF
f = 120Hz
f = 10kHz
f = 1MHz
10ms Pulse
75
l
l
l
l
l
l
l
MIN
49.5
49
–1.5
–3.5
TYP
50
50
0
0
–0.1
–0.5
–1.5
1.5
0.001
0.4
1.21
1.35
MAX
50.5
51
1.5
3.5
–3
–4
UNITS
µA
µA
mV
mV
nA
mV
mV
nA/V
mV/V
2
1.6
mA
V
V
A
nA
RMS
µV
RMS
dB
dB
dB
%/W
0.8
1.2
5.7
27
90
75
20
0.003
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Unless otherwise specified, all voltages are with respect to V
OUT
.
The LT3088 is tested and specified under pulse load conditions such
that T
J
≈ T
A
. The LT3088E is tested at T
A
= 25°C and performance is
guaranteed from 0°C to 125°C. Performance of the LT3088E over the
full –40°C and 125°C operating temperature range is assured by design,
characterization, and correlation with statistical process controls. The
LT3088I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT3088MP is 100% tested and guaranteed
over the –55°C to 150°C operating junction temperature range. The
LT3088H is tested at 150°C operating junction temperature. High junction
temperatures degrade operating lifetimes. Operating lifetime is degraded at
junction temperatures greater than 125°C.
Note 3:
Minimum load current is equivalent to the quiescent current of
the part. Since all quiescent and drive current is delivered to the output
of the part, the minimum load current is the minimum current required to
maintain regulation.
Note 4:
For the LT3088, dropout is specified as the minimum input-to-
output voltage differential required supplying a given output current.
Note 5:
Adding a small capacitor across the reference current resistor
lowers output noise. Adding this capacitor bypasses the resistor shot
noise and reference current noise; output noise is then equal to error
amplifier noise (see Applications Information section).
Note 6:
Diodes with series 400Ω resistors clamp the SET pin to the
OUT pin. These diodes and resistors only carry current under transient
overloads. During normal operation, keep the OUT-to-SET differential
voltage below 2V.
Note 7:
Load regulation is Kelvin sensed at the package.
Note 8:
This IC includes overtemperature protection that protects the
device during momentary overload conditions. Junction temperature
exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
FPGA Design Practice (Logic) is aimed at the vast number of FPGA/CPLD beginners. It explains FPGA/CPLD and related basic knowledge from scratch, and uses a motherboard-based learning kit that supports...
In the case of mixed integer and analog systems, simulation can only simulate Verilog or analog. If the digital part has only output, it is OK, just edit the voltage source and import the waveform fil...
DEBUG: Error 2863: The control PushButton2 on dialog Installation_Type_Dialog needs the icon TypicalInstall.bmp in size 48x48, but that size is not available. Loading the first available sizeInternal ...
The cursor has moved over, but the string is still displayed there. It is updated only when the line is deleted. If you enter again, it will overlap with the previous word. And this problem only occur...
Assuming the clock cycle is 40ns, the state changes of my sequential circuit are about 80ns, 160ns, 160ns, 40ns. In a state, it relies on counting loops to stay in this state until the loop count meet...
The TIA Portal software's shift instructions shift the contents of an accumulator bit by bit to the left or right. The number of bits shifted is determined by N. A left shift of N bits multiplies t...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
On August 25th, Apple's expansion in India encountered new troubles. According to Bloomberg, Foxconn Technology Group has recalled approximately 300 Chinese engineers from India, further hindering ...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
On August 22, Lantu Motors officially launched its Lanhai Intelligent Hybrid technology via an online livestream. This intelligent hybrid technology, which integrates a full-range 800V high-voltage...[Details]
On August 20th, Tiantai Robotics Co., Ltd., along with strategic partners including Shandong Future Robotics Technology Co., Ltd., Shandong Future Data Technology Co., Ltd., and Gangzai Robotics Gr...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
Batteries, at the core of new energy vehicles, are crucial to vehicle performance and range. Existing automotive batteries are categorized into lead-acid and lithium batteries. Currently, new energ...[Details]
Charging is an essential topic for electric vehicles. Batteries are a core component of new energy vehicles. So, what's the optimal charge level for electric vehicles? Based on current battery tech...[Details]
New version helps developers build secure and trustworthy embedded systems
Shanghai, China—August 21, 2025—
QNX, a division of BlackBerry Ltd., today announced the release of QNX...[Details]
Smartphones can be incredibly unintelligent. For example, consider an office full of people, each absorbed in their work. Suddenly, the silence is broken by a burst of loud pop music. A colleague's...[Details]
introduction
The rapid development of science and technology has enabled mankind to quickly move from the Internet era to the big data era. As a result, the amount of data generated by people ...[Details]
A new multi-layer diffractive optical processor can block images in one direction while allowing images in another direction to pass through.
Researchers at the University of California,...[Details]
Download Centre
京公网安备 11010802033920号
EEWORLD
