PCA9605D,118 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > semiconductor> Analog mixed-signal IC> PCA9605D,118

PCA9605D,118: DescriptionIC REDRIVER I2C 1CH 400KHZ 8SO; Categorysemiconductor Analog mixed-signal IC; File Size385KB，22 Pages; ManufacturerNXP; Websitehttps://www.nxp.com; Environmental Compliance

Download Datasheet Parametric Compare View All

PCA9605D,118 Overview

IC REDRIVER I2C 1CH 400KHZ 8SO

PCA9605D,118 Parametric

Parameter Name	Attribute value
type	buffer, redriver
application	I²C
enter	2-wire bus
output	2-wire bus
Data rate (maximum)	400kHz
Number of channels	1
delay	-
signal conditioning	-
Voltage - Power	2.7 V ~ 5.5 V
Current - Power	170µA
Operating temperature	-40°C ~ 85°C
Package/casing	8-SOIC (0.154", 3.90mm wide)
Supplier device packaging	8-SO

Preview

Download Datasheet

View All

PCA9605

Simple 2-wire bus buffer

Rev. 1 — 28 February 2011

Product data sheet

1. General description

The PCA9605 is a monolithic CMOS integrated circuit for bus buffering in applications

including I

C-bus, SMBus, DDC, PMBus, and other systems based on similar principles.

The buffer extends the bus load limit by buffering both the SCL and SDA lines, allowing

the maximum permissible bus capacitance on both sides of the buffer.

The PCA9605 includes a unidirectional buffer for the clock signal, and a bidirectional

buffer for the data signal. Slave devices which employ clock stretching are therefore not

supported.

In its most basic implementation, the buffer will allow an extended number of slave

devices to be attached to one (or more) master devices. In this case, all master devices

would be positioned on the Sxx_IN side of the PCA9605.

The direction pin (DIR) further enhances this function by allowing the unidirectional clock

signal to be reversed, thus allowing master devices on both sides of the buffer.

The enable (EN) function allows sections of the bus to be isolated. Individual parts of the

system can be brought on-line successively. This means a controlled start-up using a

diverse range of components, operating speeds and loads is easily achieved.

2. Features and benefits



Simple impedance isolating buffer for 2-wire buses



30 mA maximum static open-drain pull-down capability supports a wide range of bus

standards



Works with I

C-bus (Standard-mode, Fast-mode, Fast-mode Plus), SMBus (standard

and high power mode), and PMBus



Fast switching times allow operation in excess of 1 MHz



Enable allows bus segments to be disconnected



Hysteresis on inputs provides noise immunity



Operating voltages from 2.7 V to 5.5 V



Very low supply current



Uncomplicated characteristics suitable for quick implementation in most common

2-wire bus applications

NXP Semiconductors

PCA9605

Simple 2-wire bus buffer

clocking when communicating with them. The buffer includes hysteresis to ensure clean

switching signals are output, especially with slow rise times on high capacitively loaded

buses. Output ports are open-drain type and require external pull-up resistors.

7.3 SDA_IN, SDA_OUT — data signal inputs/outputs

The data signal buffer is bidirectional. The port (SDA_IN, SDA_OUT) which first falls

below the ‘lock voltage’ V

lock

, will take control of the buffer direction and ‘lock out’ signals

coming from the opposite side. As the ‘input’ signal continues to fall, it will then drive the

‘output’ side LOW. Again, hysteresis is applied to the buffer to minimize the effects of

noise.

At some points during the communication, the data direction will reverse, e.g., when the

slave transmits an acknowledge (ACK), or responds with its register contents. During

these times, the controlling ‘input’ side will have to rise back above the ‘unlock voltage’

unlock

) before it releases the ‘lock’, which then allows the ‘output’ side to gain control,

and pull (what was) the ‘input’ side LOW again. This will cause a ‘pulse’ on the ‘input’ side,

which can be quite a long duration in high capacitance buses. However, this pulse will not

interfere with the actual data transmission, as it should not occur during times of clock line

transition (during normal I

C-bus and SMBus protocols), and thus data signal set-up time

requirements are still met. Ports are open-drain type and require external pull-up resistors.

7.4 Enable (EN) — activate buffer operations

The active HIGH enable input (EN) can be used to disable the buffer, for the purpose of

isolating sections of the bus. The IC should only be disabled when the bus is idle. This

prevents truncation of commands which may confuse other devices on the bus. Enable

(EN) may also be used to progressively activate sections of the bus during system

start-up. Bus sections slow to respond on power-up can be kept isolated from the main

system to avoid interference and collisions. The pin must be externally driven to a valid

state.

7.5 Direction (DIR) — clock buffer direction control

The direction input (DIR) is used to change the signal direction of the SCL ports. When the

DIR pin is logic LOW, the clock signal input is SCL_IN and the buffered output is

SCL_OUT. When the DIR pin is logic HIGH, the clock signal input is SCL_OUT and the

buffered output is SCL_IN. The pin must be externally driven to a valid state.

PCA9605

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 1 — 28 February 2011

4 of 22

PCA9605D,118 Related Products

	PCA9605D,118	PCA9605DP,118
Description	IC REDRIVER I2C 1CH 400KHZ 8SO	IC REDRIVER I2C 1CH 8TSSOP
type	buffer, redriver	buffer, redriver
application	I²C	I²C
enter	2-wire bus	2-wire bus
output	2-wire bus	2-wire bus
Data rate (maximum)	400kHz	400kHz
Number of channels	1	1
Voltage - Power	2.7 V ~ 5.5 V	2.7 V ~ 5.5 V
Current - Power	170µA	170µA
Operating temperature	-40°C ~ 85°C	-40°C ~ 85°C
Package/casing	8-SOIC (0.154", 3.90mm wide)	8-TSSOP, 8-MSOP (0.118", 3.00mm wide)
Supplier device packaging	8-SO	8-TSSOP

Recommended Resources

Fuse melt blown alarm relay circuit

Switching regulated power supply circuit diagram composed of NE555

Walkman radio circuit diagram

Lighting bulb life extension device circuit

Computer motherboard circuit diagram 810 3_15

Medical Device Application Guide (Chinese Version): Medical instruments can be found in a wide variety of care settings and clinical applications. Some typical applications include: Analytical instruments, ultrasonic equipment, spectrophotometers, Endo...; 德州仪器 Analogue and Mixed Signal

[Teach you how to use Arduino + game controller + motor driver to control stepper motor]--EEWORLD University: [color=Red]Teach you step by step how to use Arduino + game controller + motor driver to control stepper motor[/color] : https://training.eeworld.com.cn/course/2057[size=5][b]In terms of hardware and ...; chenyy Industrial Control Electronics

Forming an entrepreneurial team: looking for website development technicians: Forming an entrepreneurial team: Looking for website development technicians. Many of our friends are very conflicted about starting a business. They have the passion to start a business alone, but th...; wpbjtu Embedded System

MSP430 Tutorial 11: MSP430 MCU Low Power Structure: After the basic functions of the system clock generator are established, the SCG1, SCG0, CPUOFF, and OSCOFF bits of the status register SR in the CPU are important low-power control bits. As long as a...; qinkaiabc Microcontroller MCU

Dream Travel Classmate LM3S811 Series Study Notes Serial Port Plus Built-in AD Thermometer: The Stellaris series ARM integrates a 10-bit ADC module that supports 8 input channels and an internal temperature sensor. The ADC module contains a programmable sequencer that can sample multiple ana...; 梦之旅 Microcontroller MCU

The problem of simulating serial port, has anyone done simulating serial port?: The receiving pin is pin 2 of LPC2136 ARM, and this pin needs to simulate reception. The baud rate is 9600, and the clock is 14.745600M. I used timer 0 to set two values: First: T0MR1=14745600/9600, w...; 672192076 Embedded System

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components