EEWORLDEEWORLDEEWORLD

Part Number

Search

UMP1T-S2A-S2A-S2A-S2E-S2E-S2E-E0-B

Description
UMP CONFIGURABLE POWER SUPPLY
CategoryPower/power management   
File Size1MB,6 Pages
ManufacturerArtesyn
Websitehttp://www.artesyn.com
Environmental Compliance
Download Datasheet View All

UMP1T-S2A-S2A-S2A-S2E-S2E-S2E-E0-B Overview

UMP CONFIGURABLE POWER SUPPLY

Embedded Power for
Business-Critical Continuity
µMP Series
Up to 1200 Watts
Total Power:
Up to 1200 Watts
Input Voltage:
85 - 264 Vac
120-300 Vdc
# of Outputs:
Up to 12
MicroMP 1U Multi Output
Rev. 12.12.2013
µMP
Series
1 of 6
Special Features
Full Medical EN60601 approval
• PMBus
• High efficiency
• Current limit modification
(foldback or constant current)
• High power density.
uMP4: 10.8 W/cu-in
uMP1: 15.1 W/cu-in
• Intelligent fan
(speed control/fault status)
• Downloadable GUI from website
• uP controlled PFC input with active
inrush protection
• Optional conformal coating
• Industrial temp range (-40 ºC
to 70
ºC)
• No preload required
• Industrial shock/vibration (> 50G’s)
• Low cost
• IEC or terminal block input
• Low profile 1U size
Electrical Specifications
Input
Input range:
Frequency:
Inrush current:
Efficiency:
Power Factor:
Turn-on time:
EMI filter:
Leakage current:
Radiated EMI:
Holdover storage:
AC OK:
Harmonic distortion:
Isolation:
Input fuse (internal):
Warranty:
47 - 440 Hz
40 A peak max. (soft start)
Up to 91% @ full case load
µMP4C shown
85 - 264 Vac, 120 - 350 Vdc (limited to 250 Vac/300 Vdc in medical apps)
0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
AC on 2 sec for uMP1 and 1.5 sec for uMP4, inhibit/enable 250 ms typical
CISPR 22/EN55022 Level “B”
300 µA Max. @ 240 VAC
CISPR 22/EN55022 Level “B”
16.7 ms minimum (independent of input Vac, 0 °C to 50 °C))
Signal goes low indicating loss of AC input.
Hold up = Full cycle ride thru (50 Hz)
Meets EN61000-3-2
Meets EN60950 and EN60601
uMP1: 16 A/250 V TLAG, uMP4: 10 A / 250 V. (both lines fused)
2 years
Global Inhibit/Enable: TTL, Logic “1” and Logic “0”; fan off when unit is inhibited
Environmental Specifications
Safety
UL
CSA
VDE
BABT
UL60950/UL60601-1
CSA22.2 No. 234 Level 5
EN60950/EN60601-1
Compliance to
EN60950/EN60601 BS7002
Certificate and report
Mark to LVD
Approved
-40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C.
( -20 °C start up). Meets full spec after 1/2 load. 10 min warm-up
Storage temperature:
-40 °C to 85 °C
Electromagnetic susceptibility:
Designed to meet EN61000-4; -3, -5, -6, -11 Level 3, Level 4 for -2, -4
Humidity:
Operating; non-condensing 10% to 95% RH
Vibration:
MIL-STD-810E
MTBF demonstrated:
> 350,000 hours at full load, one uMP4 case + two modules, Telcordia SR-332
calculated MTBF
Altitude:
Up to 10k feet; derate linear to 50% from 10k-30k feet
Operating temperature:
CB
CE
CCC
msp430F2274
Hello, moderator. I am using msp430F2247 microcontroller to debug nRF24L01+ module and simulate SPI timing by myself. After programming according to the framework on the Internet, I monitor mosi with ...
e时代 Microcontroller MCU
Mobile Phone RF Design Skills (Part 3)
Mobile Phone RF Design Skills (Part 3)...
feifei PCB Design
What power supply do you use for electric racing cars?
[i=s] This post was last edited by paulhyde on 2014-9-15 09:26 [/i] What kind of power do you guys use for electric racing cars? It seems like ordinary batteries won't work after running for a while. ...
melodyooo Electronics Design Contest
PIC16F877A CCP input capture issue
Guys, please help me see where the program is wrong? void interrupt for CCP input capture CCP1INT (void) { if(CCP1IF==1) { CCP1IF=0; if(LastCaptureData==0) // Capture the first rising edge { LastCaptu...
yejiandong84 Microchip MCU
Analysis: TI Cup [Competition Question Release] Point Light Source Tracking System (Question B)
[i=s]This post was last edited by paulhyde on 2014-9-15 08:56[/i][i=s]This post was last edited by paulhyde on 2014-9-15 08:56[/i] Please help the students who are participating in the competition to ...
fish001 Electronics Design Contest
Solve the problem of "PL2303HXA has been discontinued since 2012, please contact the supplier" USB not being recognized
Original link : https://blog.csdn.net/wtf3505/article/details/104138727 Refer to the solution on the Internet, first download the original device driver, and then install the old driver below...
通宵敲代码 Making friends through disassembly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 581  734  570  253  710  12  15  6  36  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号