EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005ACU2D-XXEN

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005ACU2D-XXEN Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com

Recommended Resources

Non-inverting proportional amplifier feedback resistor setting
I would like to ask you guys, for the op amp's inverse proportional amplifier circuit (as shown in the figure), how to correctly select the values of R1 and R2 under the same ratio? Are there any rest...
ericzh Analog electronics
I encountered a problem about Keil today
In the past few days, I have developed some functions of TouchGFX and added controls dynamically. It was relatively smooth during computer simulation. However, when it was burned to the development bo...
PowerWorld Programming Basics
Cumulative error analysis and clock frequency optimization for UART communication in MSP430FR2311
[i=s]This post was last edited by Aguilera on 2019-1-9 11:00[/i] [align=left][size=3][color=#ffffff] [/color][/size][size=3][color=#000000][backcolor=white] In UART communication design, engineers wil...
Aguilera Microcontroller MCU
How to configure the option bytes of stm8 in software
I want to ask you this question too....
6562748 stm32/stm8
HTC Desire S G12 Teardown
[size=10.5000pt] [/size] [font=微软雅黑][size=3]I am bored, and here I am again~~~~:pleased:[/size][/font] [font=微软雅黑][size=3]This time it is HTC Desire S, a phone I bought a few years ago. I accidentally...
国土安全局 Creative Market
[Shanghai Hangxin ACM32F070 development board + touch function evaluation board] Voltage meter implementation and ADC performance rough test
Preface This time, based on ADC and segment code display, the function of a voltmeter is realized. process Based on LCD_TK. Use the upper 4 digits to display the value in mV. From the schematic diagra...
qinyunti Domestic Chip Exchange

Popular Articles

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2906  2829  664  485  896  59  57  14  10  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号