EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005ACB1H-28SL

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet View All

SIT9005ACB1H-28SL Overview

OSC MEMS

SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
Check out the new post function, everyone take a look~~~
Previously, Blue Eye Fox and wangjiafu1985 suggested that the forum should have a function to view new posts. This function was added today:As shown in the figure: Label 1 remains the same, including ...
soso Suggestions & Announcements
Winding inductance of electrolytic capacitor
The electrolytic capacitor is made of two strips of aluminum foil with insulating paper. Because it is wound, it is considered to be an inductor. This conclusion has been circulated for decades. I don...
PowerAnts Analog electronics
As a beginner, how can I learn the relevant knowledge of WINCE?
Since I will be going to the company for internship in two months, the engineer from the relevant department of the company informed me that I should first familiarize myself with the wince system and...
t63056 Embedded System
How does COMBOBOX get focus?
I want to do something when COMBOBOX gets the focus. The method I used is if(GetFoucs()->GetDlgCtrlID==IDC_XXX), but the cursor is clearly on COMBOBOX but it doesn't seem to get the focus. The same co...
2002xiao Embedded System
I have some questions about a small program and need some advice
module count4(out,reset,clk); output[3:0] out; input[3:0] reset,clk; reg[3:0] out; always @(posedge clk)beginif(reset) out=0;else out=out+1;end endmoduleIs the reason why out is defined as a register ...
leomeng FPGA/CPLD
2440, bootloader problem
My bsp contains stepldr and eboot, I want to run eboot, but after burning stepldr.nb1 into flash, dnw shows garbled characters! ! ! ! This is the initial code of the serial port: void Uart_Init(void) ...
ricky03221115 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 664  868  885  2478  676  14  18  50  45  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号