EEWORLDEEWORLDEEWORLD

Part Number

Search

TNPW0402432RBHED

Description
RES 432 OHM 0.1% 1/10W 0402
CategoryPassive components   
File Size136KB,8 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

TNPW0402432RBHED Overview

RES 432 OHM 0.1% 1/10W 0402

TNPW0402432RBHED Parametric

Parameter NameAttribute value
resistance432 Ohms
Tolerance±0.1%
Power (W)0.1W,1/10W
componentthin film
characteristicSulfur resistant, automotive grade AEC-Q200 automotive certified, moisture resistant
Temperature Coefficient±50ppm/°C
Operating temperature-55°C ~ 155°C
Package/casing0402 (1005 Metric)
Supplier device packaging402
size/dimensions0.039" long x 0.020" wide (1.00mm x 0.50mm)
Height - Installation (maximum)0.016"(0.40mm)
Number of terminals2
failure rate-
TNPW
www.vishay.com
Vishay
Lead (Pb)-Bearing High Stability Thin Film Chip Resistors
FEATURES
• Metal film layer on high quality ceramic
• SnPb termination plating, Pb content > 6 %
• Excellent overall stability at different environmental
conditions
0.05 % (1000 h rated power at 70 °C)
• Low temperature coefficient and tight tolerances (± 0.1 %;
± 10 ppm/K)
• Single lot date code available
APPLICATIONS
• Military
• Avionics
• Industrial
TNPW High Stability Thin Film Chip Resistors are the perfect
choice for most fields of modern electronics where lead
(Pb)-bearing terminations are mandatory and reliability and
stability are of major concern.
TECHNICAL SPECIFICATIONS
DESCRIPTION
Imperial size
Metric size code
Resistance range
Resistance tolerance
Temperature coefficient
Climatic category (LCT/UCT/days)
Rated dissipation,
P
70 (2)
Operating voltage,
U
max.
AC
RMS
or DC
Permissible film temperature,
F max.
Operating Temperature Range
Thermal resistance
(3)
Insulation voltage:
U
ins
1 min
Continuous
Failure rate: FIT
observed
75 V
75 V
100 V
75 V
200 V
75 V
0.3 x 10
-9
/h
300 V
75 V
300 V
75 V
870 K/W
550 K/W
55/125/56
0.063 W
50 V
TNPW0402
0402
RR1005M
10
to 100 k
TNPW0603
0603
RR1608M
10
to 332 k
TNPW0805
0805
RR2012M
10
to 1 M
± 1 %; ± 0.5 %; ± 0.1 %
± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
55/125/56
0.1 W
75 V
55/125/56
0.125 W
150 V
155 °C
-55 °C to 125 °C (155 °C)
440 K/W
220 K/W
170 K/W
55/125/56
0.25 W
200 V
55/125/56
0.33 W
200 V
TNPW1206
1206
RR3216M
10
to 2 M
TNPW1210
(1)
1210
RR3225M
10
to 3.01 M
Notes
(1)
The detail specification EN140401-801 does not cover this product size.
(2)
Rated voltage
P
x
R
. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat
flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not
exceeded.
(3)
Measuring conditions in accordance with EN 140401-801.
Revision: 24-Jan-14
Document Number: 31006
1
For technical questions, contact:
thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
A question about NIOS II processor
A test program for the DE3 board. It works fine when using SLIDE_SWITCH, but it stops working when SLIDE_SWITCH is changed to BUTTON. But if you use it directly [code] mask=IORD_ALTERA_AVALON_PIO_DATA...
cnic Embedded System
Key input program problem
The following is the key input program I refer to, P2.0, P2.1, P2.2, P2.3 key input, now I debug online, the following problems appear!1. I run at full speed and there is no key input, but keybuf is a...
sumption Microcontroller MCU
I have created the MMS PDU and want to know if it is correct. What should I do?
As the title says, I have been able to pack text, pictures and other things into PDU, but I want to test whether this PDU is correct and whether it can be recognized by the MMS center! How should I do...
shengming217 Embedded System
What tool can I use to check the Ethernet upload data speed?
[size=6][b]Is this the speed of 25Mbps? Is this[/b][/size][size=6][b]accurate? [/b][/size]...
zzgezi Microcontroller MCU
I would like to ask the experts: In emWin, is WM_HBKWIN 0?
[i=s] This post was last edited by liuchang--- on 2015-8-31 14:15 [/i] As the title says: If I change WM_HBKWIN to 0, the displayed result is the same. But I see the definition of WM_HBKWIN: #define W...
liuchang--- Real-time operating system RTOS
Open a thread to talk about the experience of using EZ430
I have been busy recently and have no time to hang out on the forum or look at this kit, so I have not finished what I should do. I apologize to everyone in advance. Today I will post my small unfinis...
ch0721 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1905  2122  2874  685  1060  39  43  58  14  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号