PA2982.191HLT datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> PA2982.191HLT

PA2982.191HLT: DescriptionFIXED IND 190NH 38A 0.35 MOHM; CategoryPassive components; File Size649KB，3 Pages; ManufacturerPulse Electronics Power; Environmental Compliance

Download Datasheet Parametric View All

PA2982.191HLT Overview

FIXED IND 190NH 38A 0.35 MOHM

PA2982.191HLT Parametric

Parameter Name	Attribute value
type	-
Material - Core	-
inductance	190nH
Tolerance	±10%
Rated current	38A
Current - saturation value	48A
shield	shield
DC resistance (DCR)	0.35 milliohms
Q value at different frequencies	-
Frequency - Self-resonance	-
grade	-
Operating temperature	-40°C ~ 130°C
Inductor Frequency - Test	100kHz
characteristic	-
Installation type	surface mount
Package/casing	non-standard
Supplier device packaging	-
size/dimensions	0.433" long x 0.315" wide (11.00mm x 8.00mm)
Height - Installation (maximum)	0.201"（5.10mm）

Preview

Download Datasheet

View All

Pulse Jack

SMT Power Inductors

Power Beads - PA2982.XXXHL Series

Current Rating:

Over 81Apk

Inductance Range:

100nH to 220nH

Height:

5.0 and 5.1 mm Max

Footprint:

11.0mm x 8.0mm Max

Halogen Free

Inductance

@ 0A

(nH +/- 10%)

100

120

150

190

220

Electrical Specifications @ 25°C — Operating Temperature - 40°C to +130°C

Saturation Current

Inductance

Irated

DCR

(A TYP)

@Irated

(ADC)

(mW nominal)

(nH TYP)

25°C

100°C

120

140

0.35 +/- 8.6%

180

210

Electronics

Part

Number

PA2982.101HL

PA2982.121HL

PA2982.151HL

PA2982.191HL

PA2982.221HL

Heating Current

(A TYP)

NOTES:

1. Inductance measured at 100kHz, 100mVrms.

2. Inductance at Irated is the value of the inductance at 25°C at the listed rated current.

3. The rated current as listed is either the saturation current (25°C or 100°C) or the heating current depending on

which value is lower.

4. The nominal DCR is measured from point a to point b , as shown below on the mechanical drawing.

5. The saturation current is the typical current which causes the inductance to drop by 20% at the stated ambient

temperatures (25°C, 100°C and 125°C). This current is determined by placing the component in the specified ambi-

ent environment and applying a short duration pulse current

(to eliminate self-heating effects) to the component.

6. The heating current is the DC current which causes the part temperature

to increase by approximately 40°C when used in a typical application.

7. In high volt*time applications, additional heating in the component can occur due to core losses in the inductor

which may neccessitate derating the current in order to limit the temperature rise of the component. To deter-

mine the approximate total losses (or temperature rise) for a given application, the coreloss and temperature

rise curves can be used.

8. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part number (i.e. PA2982.221HL

becomes PA2982.221HLT).

Pulse complies to industry standard tape and reel specification EIA481. The tape and reel for this product has a

width (W=24mm), pitch (Po=12.0mm) and depth (Ko=5.5mm).

9. The temperature of the component (ambient plus temperature rise) must be within the stated operating tem-

perature range.

Mechanical

PA2982.XXXHL

Schematics

Weight

. . . . . . . . . . . 2.4 grams

Tape & Reel

. . . . . . . . 560/reel

Dimensions:

Inches

Unless otherwise specified,

all tolerances are ± .010

0,25

pulseelectronics.com

P712.A (2/12)

Recommended Resources

Inverter circuit part 5a

Two-way touch switch (1)

Pressurized water supply level controller circuit.gif

High-precision sample and hold circuit diagram

Pyroelectric infrared sensor corridor lighting circuit

High-precision 6-60 second timer

USB3.0 physical layer test introduction and difficulty analysis: USB (Universal Serial Bus) is used to connect peripheral devices such as keyboards, mice, printers, scanners, digital cameras, MP3, USB flash drives, etc. to computers. It standardizes the interface b...; 安_然 Test/Measurement

Electrostatic discharge failure: [p=22, null, left][color=rgb(51, 51, 51)][font=Arial, Helvetica, sans-serif, 宋体][b]Charge Generation and Transfer Mechanism[/b][/font][/color][/p][p=22, null, left][color=rgb(51, 51, 51)][font=Arial, ...; wstt Test/Measurement

Solar Controller Information Sharing: A relatively powerful solar controller, if you need it,...; dengnian Energy Infrastructure?

Very detailed introductory article FPGA_SOPC_starter: Very detailed introductory article FPGA_SOPC_starter, very suitable for Nios novices to learn, very good information...; huan564728741 FPGA/CPLD

[SAMR21 new gameplay] 35. HCSR04 ultrasonic sensor: [i=s]This post was last edited by dcexpert on 2019-10-19 19:44[/i]The HCSR04 ultrasonic sensor calculates the distance by measuring the pulse width, so the pulse width can be captured using the PulseI...; dcexpert MicroPython Open Source section

[Urgent help] Problems encountered when simulating Xilinx Cordic IP core: I use cordic core to implement square root function, but when I use modelsim simulation, the output is always blue line, and there are many warning prompts. # Loading work.sqare_test_tb # Loading work...; cz4811674 FPGA/CPLD

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components