EEWORLDEEWORLDEEWORLD

Part Number

Search

3N261TX

Description
OPTOISOLATOR 1KV TRANS TO72-4
CategoryLED optoelectronic/LED   
File Size1MB,17 Pages
ManufacturerTT Electronics
Download Datasheet Parametric View All

3N261TX Online Shopping

Suppliers Part Number Price MOQ In stock  
3N261TX - - View Buy Now

3N261TX Overview

OPTOISOLATOR 1KV TRANS TO72-4

3N261TX Parametric

Parameter NameAttribute value
Number of channels1
Voltage - Isolation1000VDC
Current transfer ratio (minimum value)5% @ 1mA
Current transfer ratio (maximum)-
Open/close time (typ.)-
Rise/Fall Time (Typical)20µs, 10µs (maximum)
input typeDC
Output typetransistor
Voltage - Output (maximum)30V
Current - Output/Channel30mA
Voltage - Forward (Vf) (Typical)1.5V (maximum)
Current - DC Forward (If)40mA
Vce saturation value (maximum value)300mV
Operating temperature-55°C ~ 125°C
Installation typeThrough hole
Package/casingTO-206AF, TO-72-4 metal can
Supplier device packagingTO-72-4
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Features:
5,000 Vrms electrical isolation
Choice of a Single and Dual LED
Phototransistor or Photodarlington Sensor
Low-cost plastic Dual-In-Line (DIP) package
UL Certification No: E58730
VDE No
:
40026625 40026536, 40026654
Approval Agency:
Description:
The OPIA series optocouplers are designed for applications that use an analog output (Phototransistor or
Photodarlington) in a dual-in-line package. A wide selection of configurations are available. With typical isolation
voltage of 5,000 Volts(RMS), these products meet typical power system isolation requirements.
Theory of operation: The LED transmitter is used to illuminate the Photosensor providing electrical isolation
between two power systems while maintaining the ability to transmit information from one power system to the
other. In many applications, analog signal levels may be required to be transmitted between two power systems
while maintaining isolation between the power systems up to 5,000 volts(RMS). A variety of LED and photosensor
configurations are available depending on the system requirements.
The ratio Current Transfer Ratio (CTR) is determined by using the output current and input current for analog
photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device.
CTR
=
Photosenso
r
Current
LED
Current
=
20
mA
* 100
=
200
10
mA
All DIP product is shipped in a shipping tube with “TU” identified on the end of the part number.
Example: OPIA817DTUE is a 4-Pin DIP shipped in a tube (TU).
Applications:
High voltage isolation: 5,000 Volts RMS
PCBoard power system isolation
Industrial equipment power isolation
Medical equipment power isolation
Office equipment
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.5
8/09
Page 1 of 17
OPTEK Technology Inc. —
1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
A very good forum
I bought the 4412 development board from Youmi before, and I really regret it. I posted on their forum. Everyone replied, this forum is still good, the discussion atmosphere is very good, I regret buy...
matao1314 Embedded System
51 MCU variable definition
How to define variables in 51 MCU? Where are global variables and local variables stored? And if I want to define a variable in user RAM with address 0x32, how to define the variable in the bit addres...
davidlong98 51mcu
Please advise on the use of GDO0 in CC2500
void RFSendPacket(char *txBuffer, char size) { TI_CC_SPIWriteBurstReg(TI_CCxxx0_TXFIFO, txBuffer, size); // Write TX data TI_CC_SPIStrobe(TI_CCxxx0_STX); // Change state to TX, initiating // data tran...
nishishab Embedded System
Can you guys help me check if my circuit analysis is correct?
As shown in the figure, I want to get a fixed VOUT from VIN, and limit the current at VOUT to a value. For example, if I input VIN15V and want to get VOUT5V, ic=1A, then ib=5mA. My analysis is this. T...
startt Analog electronics
【CN0095】Capacitance-to-digital converter (CDC) AD7150 for proximity sensing applications
Circuit Functionality and BenefitsThe circuit described in this article provides a basis for developing proximity sensing applications using the AD7150 capacitance-to-digital converter (CDC). The AD71...
EEWORLD社区 ADI Reference Circuit
【Suzhou】Maike Network is recruiting talents
Company ProfileSuzhou Maxnet Network Security Technology Co., Ltd. (Maxnet) is a young team of only 6 years old. We are not experienced, but we insist on innovation; we are not overtime crazy, but we ...
hyyomzd Recruitment

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1721  1568  2538  268  917  35  32  52  6  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号