EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63112-490L

Description
Line Driver, 1 Driver, Hybrid, MDFP24
CategoryDrivers and interfaces   
File Size124KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63112-490L Overview

Line Driver, 1 Driver, Hybrid, MDFP24

BUS-63112-490L Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerData Device Corporation
package instructionDFP, FL24,1.3,100
Reach Compliance Codecompliant
ECCN codeEAR99
Is SamacsysN
Differential outputYES
Number of drives1
Interface integrated circuit typeLINE DRIVER
JESD-30 codeR-MDFP-F24
JESD-609 codee0
Number of terminals24
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package body materialMETAL
encapsulated codeDFP
Encapsulate equivalent codeFL24,1.3,100
Package shapeRECTANGULAR
Package formFLATPACK
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply5,+-12/+-15 V
Certification statusNot Qualified
Maximum receive delay
surface mountYES
technologyHYBRID
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
Base Number Matches1
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
[RVB2601 Creative Application Development]--Section 5 RVB2601 Connecting to Alibaba Cloud Platform
After a month, during the May Day holiday, I came back and picked up RVB2601 again. This time I mainly referred to sipower's post and quickly connected it to Alibaba Cloud. 1. The first step is to reg...
qq4988 XuanTie RISC-V Activity Zone
Shameful design mistake
[font=楷体_GB2312][size=3]I made a test board some time ago, which used a control relay. In order to achieve complete isolation, I used an optocoupler to drive the relay, but a problem occurred. I will ...
lixiaohai8211 Analog electronics
About the problem of PDT data transmission on EMIF interface
I want to use PDT transmission to transfer the data in the FIFO in the FPGA to the SDRAM expanded by DSP CE0, but I can't read the data. The data in the SDRAM has all become a single value. I don't kn...
ayumi411 DSP and ARM Processors
Smartphone 2003 migration issues
I have encountered a very difficult problem. I first developed a sp program on VS2005. It is a wtl project. Then I transplanted the 03 version to EVC. The compilation was successful, but when it was p...
siguang Embedded System
The dead zone problem
Our company is going to make washing machines, and the DC brushless motors do not have Hall.I haven't tried it before. I bought a motor development board and the dead zone in the program is 1.84us. Th...
chenbingjy Motor Drive Control(Motor Control)
Problems in the application of interrupts of PIC16F887 microcontroller
Is it a problem to turn off one interrupt and then turn on the second one immediately? Can an expert give me some advice?...
future2014 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2000  1896  735  103  2409  41  39  15  3  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号