XC6111A624 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > XC6111A624

Preview

XC6111A624: DescriptionCMOS Voltage Detector; File Size525KB，26 Pages; ManufacturerTOREX; Websitehttp://www.torex.co.jp/chinese/

Download Datasheet View All

XC6111A624 Overview

CMOS Voltage Detector

Preview

Download Datasheet

View All

Preliminary

◆CMOS

Voltage Detector

◆Manual

Reset Input

◆Watchdog

Functions

◆Built-in

Delay Circuit

◆Detect

Voltage Range: 1.6~5.0V, ± 2%

◆Reset

Function is Selectable

DFL

(Low When Detected)

DFH

(High When Detected)

■APPLICATIONS

●Microprocessor

reset circuits

●Memory

battery backup circuits

●System

power-on reset circuits

●Power

failure detection

■GENERAL

DESCRIPTION

■FEATURES

Detect Voltage Range

Hysteresis Range

: 1.6V ~ 5.0V, +2%

(100mV increments)

: V

x 5%, TYP.

(XC6101~XC6107)

x 0.1%, TYP.

(XC6111~XC6117)

: 1.0V ~ 6.0V

The XC6101~XC6107, XC6111~XC6117 series are

groups of high-precision, low current consumption voltage

detectors with manual reset input function and watchdog

functions incorporating CMOS process technology. The

series consist of a reference voltage source, delay circuit,

comparator, and output driver.

With the built-in delay circuit, the XC6101 ~ XC6107,

XC6111 ~ XC6117 series’ ICs do not require any external

components to output signals with release delay time.

Moreover, with the manual reset function, reset can be

asserted at any time. The ICs produce two types of

output; V

DFL

(low when detected) and V

DFH

(high when

detected).

With the XC6101 ~ XC6105, XC6111 ~ XC6115 series’

ICs, the WD pin can be left open if the watchdog function

is not used.

Whenever the watchdog pin is opened, the internal

counter clears before the watchdog timeout occurs.

Since the manual reset pin is internally pulled up to the V

pin voltage level, the ICs can be used with the manual

reset pin left unconnected if the pin is unused.

The detect voltages are internally fixed 1.6V ~ 5.0V in

increments of 100mV, using laser trimming technology.

Six watchdog timeout period settings are available in a

range from 6.25msec to 1.6sec.

Seven release delay time 1 are available in a range from

3.13msec to 1.6sec.

Operating Voltage Range

Detect Voltage Temperature

Characteristics

: +100ppm/

C (TYP.)

Output Configuration

: N-channel open drain,

CMOS

Watchdog Pin

: Watchdog input

If watchdog input maintains

‘H’ or ‘L’ within the watchdog

timeout period, a reset signal

is output to the RESET

output pin

Manual Reset Pin

: When driven ‘H’ to ‘L’ level

signal, the MRB pin voltage

asserts forced reset on the

output pin.

Release Delay Time

: 1.6sec, 400msec, 200msec,

100msec, 50msec, 25msec,

3.13msec (TYP.) can be

selectable.

Watchdog Timeout Period

: 1.6sec, 400msec, 200msec,

100msec, 50msec,

6.25msec (TYP.) can be

selectable.

■TYPICAL

APPLICATION CIRCUIT

■TYPICAL

PERFORMANCE

CHARACTERISTICS

●Supply

Current vs. Input Voltage

XC61X1~XC61X5 (2.7V)

Supply Current:

ISS (µA)

Input Voltage:

VIN (V)

Ta=-40

℃

Ta=25

℃

Ta=85

℃

* Not necessary with CMOS output products.

* ‘x’ represents both ‘0’ and ‘1’. (ex. XC61x1⇒XC6101 and XC6111)

XC6101_07_XC6111_17 ETR0207_009

1/26

Recommended Resources

AAT circuit for sectional bus backup power b

battery monitor

OPT202 gain adjustment circuit

Pressure sensor two-wire transmission circuit

Pocket electronic timer circuit diagram

555 oscilloscope adds a circuit with trigger sweep function

Question + How to add through holes in the copper area of PCB: [i=s] This post was last edited by hjl240 on 2014-3-9 17:42 [/i] [size=5] I saw that there is a hole in the middle of the touch button of the msp430f5529 learning board, as shown below: [/size][size=5...; hjl240 PCB Design

Some questions about eboot: After compiling, eboot can start to the menu selection, but it can't go any further: click F: format flash, prompt: ERROR: InitPartitionMgr: failed to initialize partition manager. The source code is ...; xue948 Embedded System

Why can't QuartusII open other people's projects? (Urgent...): Why can't QuartusII open someone else's project? After opening QuartusII, I select "FILE" -> "open project" and then select the project, but an error message appears: "Error: Can't open project -- you...; han_haomail Embedded System

Chipidea, the world's leading provider of analog and mixed-signal IP, joins MIPS Technologies: :D Chipidea, the world's leading supplier of analog and mixed-signal IP, joins MIPS Technologies: Chipidea and MIPS Technologies have joined forces to create the world's second largest semiconductor I...; 一直很用心 Embedded System

Thanks to my roommate for his cell phone: Haha, after disassembling the hard drive yesterday, I went to my roommate's place and took a look around. Hey, what did I find:pleased: It was his old phone that just broke. Haha, thank you again to m...; 二白啊啊 Making friends through disassembly

What file is Bootloader?: I have a question: Are the EBOOT.bin and EBOOT.nb0 in \WINCE600\OSDesigns\2451\2451\RelDir\smdk2450_ARMV4I_Release the bootloader? If there is no bootloader on the bare chip, can I burn EBOOT.nb0 firs...; binbin001 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components