EEWORLDEEWORLDEEWORLD

Part Number

Search

C1206X104J8JAC7800

Description
CAP CER 0.1UF 10V U2J 1206
CategoryPassive components   
File Size1MB,19 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Environmental Compliance
Download Datasheet Parametric View All

C1206X104J8JAC7800 Overview

CAP CER 0.1UF 10V U2J 1206

C1206X104J8JAC7800 Parametric

Parameter NameAttribute value
capacitance.1µF
Tolerance±5%
Voltage - Rated10V
Temperature CoefficientU2J
Operating temperature-55°C ~ 125°C
characteristicSoft terminal
grade-
applicationBoardflex sensitive
failure rate-
Installation typeSurface mount, MLCC
Package/casing1206 (3216 metric)
size/dimensions0.130" long x 0.063" wide (3.30mm x 1.60mm)
Height - Installation (maximum)-
Thickness (maximum)0.035"(0.88mm)
lead spacing-
Lead form-
notifyThere is currently market demand for these product types, so lead times will change and extend. Lead times may vary.
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), U2J Dielectric,
10 – 50 VDC (Commercial & Automotive Grade)
Overview
The KEMET Flexible Termination (FT-CAP) Multilayer
Ceramic Capacitor in U2J dielectric incorporates a unique,
flexible termination system that is integrated with KEMET’s
standard termination materials. A conductive silver epoxy
is utilized between the base metal and nickel barrier layers
of the KEMET standard termination system in order to
establish pliability while maintaining terminal strength,
solderability and electrical performance. This technology
was developed in order to address the primary failure mode
of MLCCs — flex cracks, which are typically the result of
excessive tensile and shear stresses produced during
board flexure and thermal cycling. Flexible termination
technology inhibits the transfer of board stress to the
rigid ceramic body, therefore mitigating flex cracks which
can result in low insulation resistance (IR) or short circuit
failures. KEMET automotive grade capacitors meet the
demanding Automotive Electronics Council's AEC-Q200
qualification requirements.
Although this technology does not eliminate the potential
for mechanical damage that may propagate during extreme
environmental and handling conditions, it does provide
superior flex performance over standard termination
systems. FT-CAP complements KEMET’s Open Mode,
Floating Electrode (FE-CAP), Floating Electrode with Flexible
Termination (FF-CAP), and KEMET Power Solutions (KPS)
product lines provide a complete portfolio of flex mitigation
solutions.
Combined with the stability of U2J dielectric and designed
to accommodate all capacitance requirements, these flex-
robust devices are RoHS compliant, offer up to 5 mm of
flex-bend capability and capacitance change limited to –750
±20 ppm/°C from –55°C to +125°C. These devices are lead-
free, RoHS and REACH compliant without exception and are
capable of withstanding multiple passes through a lead-free
solder reflow profile.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C
Ceramic
1206
X
104
Capacitance
Code (pF)
Two significant
digits +
number of
zeros.
J
3
J
A
C
Termination Finish
C = 100% Matte Sn
TU
Packaging/
Grade (C-Spec)
See
"Packaging
C-Spec
Ordering
Options Table"
below
Case Size
Specification/
(L" x W")
Series
0603
0805
1206
1210
1812
X = Flexible
Termination
Failure Rate/
Capacitance
Rated Voltage
Dielectric
1
Design
Tolerance
(VDC)
F = ±1%
G = ±2%
J = ±5%
K = ±10%
M = ±20%
8 = 10
4 = 16
3 = 25
5 = 50
J = U2J
A = N/A
1
Additional capacitance tolerance offerings may be available. Contact KEMET for details.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1087_U2J_FT-CAP_SMD • 3/13/2018
1
Measuring resistance of common IO port, verification of using it as AD port
[i=s] This post was last edited by long521 on 2016-12-26 09:05 [/i] I have seen this method of measuring temperature with ordinary IO ports in some books before, and I have verified it myself recently...
long521 Microchip MCU
ON Network Intelligent Adapter Based on PCI Bus
:This paper introduces the overall design, CPLD decoding, and WDM driver development of a LON network intelligent adapter based on PCI bus. Using this adapter, a LON network distributed measurement an...
frozenviolet RF/Wirelessly
A small piece, a big lesson - Let's talk about filters
Have you ever thought about what the glass on the CCD is used for? --- That filter, the correct name is "Optical Low Pass Filter" (OLPF)! Ah! Isn't it just a broken piece of glass? Let me tell you: Th...
fish001 Industrial Control Electronics
STM8 Hardware I2C Issue
As the title says, I am recently adjusting the hardware I2C of STM8 to read and write 24C16. I don't know whether it should be in 7-bit mode? How to configure it to use 7-bit mode or 10-bit mode?...
jemofh stm32/stm8
Problem with Mbus master receiving circuit!!!!!!!!!!!!!!!!!!
The main function of this circuit is to detect the voltage fluctuation at both ends of SR and realize the on and off of the optocoupler through the comparison of U1 differential input and U2. What I w...
放开那个鸡腿 Analogue and Mixed Signal
2440VGA output configuration
I use CH7005 to convert LCD signal to VGA output. It can output in VGA at 640*480 resolution, but it cannot output in 800*600 resolution. [color=#0000FF]The relevant registry configuration for 640*480...
songfgd Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2803  1117  443  857  1275  57  23  9  18  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号