The Reflector is sold separately. Select the Reflector model most suited to the application.
The sensing distance specified is possible when the E39-R1S is used.
Values
in parentheses indicate the minimum required distance between the Sensor and Reflector.
Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver.
M12 Standard Pre-wired Connector Models are also availavble.
When ordering, add "-M1J 0.3M" to the end of the model number (e.g., E3Z-T61-M1J 0.3M).
The cable is 0.3 m long.
Accessories (Order Separately)
Slit
(A Slit is not provided with Through-beam Sensors) Order a Slit separately if required.
[Refer to
Dimensions
on page 16.]
Slit width
0.5-mm dia.
1-mm dia.
2-mm dia.
0.5
×
10 mm
1
×
10 mm
2
×
10 mm
Sensing distance
E3Z-T@@
E3Z-T@@A
50 mm
35 mm
200 mm
150 mm
800 mm
550 mm
1m
700 mm
2.2 m
1.5 m
5m
3.5 m
Minimum detectable object
(Reference value)
0.2-mm dia.
0.4-mm dia.
0.7-mm dia.
0.2-mm dia.
0.5-mm dia.
0.8-mm dia.
Model
E39-S65A
E39-S65B
E39-S65C
E39-S65D
E39-S65E
E39-S65F
Contents
One set
(contains Slits for
both the Emitter and
Receiver)
Reflectors
(Reflector required for Retroreflective Sensors) A Reflector is not provided with the Sensor. Be sure to order a Reflector separately.
[Refer to
Dimensions
on
E39-L/E39-S/E39-R]
Sensing distance
*
E3Z-R
E3Z-R@K
E3Z-B@1/-B@6
Reference value
Rated value
(sensing
(sensing
Rated value
Rated value
distance of 15 m) distance of 10 m)
---
---
3 m (100 mm)
2 m (100 mm)
---
4 m (100 mm)
3 m (150 mm)
500 mm (80 mm)
---
---
---
5 m (100 mm)
---
---
---
2.5 m (100 mm)
---
---
---
3.5 m(100 mm)
---
E3Z-B@2/-B@7
Model
Rated value
---
Name
Quantity
Remarks
2 m (500 mm)
---
---
---
Reflector
E39-R1
E39-R1S
E39-R2
E39-R9
E39-R10
E39-R1K
1
1
1
1
1
1
---
---
---
---
1.5 m (50 mm)
E39-R3
1
---
---
---
---
700 mm (150 mm)
E39-RS1
1
---
---
---
---
Tape Reflector
1.1 m (150 mm)
E39-RS2
1
---
---
---
---
1.4 m (150 mm)
E39-RS3
1
Note: 1. If you use the Reflector at any distance other than the rated distance, make sure that the stability indicator lights properly when you install the Sensor.
2. Refer to
Reflectors
on
E39-L/E39-S/E39-R
for details.
*
Values
in parentheses indicates the minimum required distance between the Sensor and Reflector.
Fog Preventive
Coating
Small Reflector
3 m (100 mm)
---
500 mm (80 mm)
2 m (500 mm)
•
Retro-reflective
models are not
provided with
Reflectors.
•
The MSR function
is enabled.
Mutual Interference Protection Filter
A Filter is not provided with the Sensor (for the through-beam E3Z-T@@A). Order a Filter separately if required.
Sensing distance
Appearance/Dimensions
10.8
7.4
4.9
1
Model
Quantity
Remarks
Can be used with the E3Z-T@@A Through-
beam models. The arrow indicates the direc-
tion of polarized light. Mutual interference
can be prevented by altering the direction of
polarized light from or to adjacent Emitters
and Receivers.
3m
31.4 11.2
0.2
E39-E11
Two sets each for the
Emitter and Receiver
(total of four pieces)
Note: The polarization directions of the Filters are offset by 90º to prevent interference. When you install the Emitter and Receiver, install them at the same angle to
maintain this offset.
3
E3Z
Mounting Brackets
A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
[Refer to
Dimensions
on
E39-L/E39-S/E39-R]
Appearance
Model (material)
E39-L153
(SUS304)
*1
Quantity
Remarks
Appearance
Model (material)
E39-L98
(SUS304)
*2
Mounting Brackets
E39-L104
(SUS304)
*1
1
E39-L150
(SUS304)
1
(Sensor adjuster)
Easily mounted to the
aluminum frame rails of
conveyors and easily
adjusted.
E39-L151
(SUS304)
E39-L142
(SUS304)
*2
1
Horizontal Protective
Cover Bracket
1
For left to right adjust-
ment
Quantity
Remarks
Metal Protective Cover
Bracket
1
1
E39-L43
(SUS304)
*2
1
Horizontal Mounting
Brackets
E39-L44
(SUS304)
1
Rear Mounting Bracket
E39-L144
(SUS304)
*2
1
Compact Protective
Cover Bracket (For E3Z
only)
Note: 1. When using Through-beam models, order one bracket for the Receiver and one for the Emitter.
2. Refer to
Mounting Brackets
on
E39-L/E39-S/E39-R
for details.
*1. Cannot be used for Standard Connector models with mounting surface on the bottom. In that case, use Pre-wired Connector models.
*2. Cannot be used for Standard Connector models.
Sensor I/O Connectors (Sockets on One Cable End)
(Models for Connectors and Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
[Refer to
Dimensions
for
XS3.]
Size
Cable
Straight
*2
Standard
L-shaped
*2 *3
PUR
(Polyure-
thane) cable
*1
Straight
*2
L-shaped
*2 *3
Straight
*2
L-shaped
*2 *3
Appearance
Cable type
2m
5m
2m
5m
2m
5m
2m
5m
2m
5m
2m
5m
4-wire
Model
XS3F-M421-402-A
XS3F-M421-405-A
XS3F-M422-402-A
XS3F-M422-405-A
XS3F-M421-402-L
XS3F-M421-405-L
XS3F-M422-402-L
XS3F-M422-405-L
XS3F-M421-402-R
XS3F-M421-405-R
XS3F-M422-402-R
XS3F-M422-405-R
M8
Vibration-proof
robot cable
Note: 1. When using Through-beam models, order one connector for the Receiver and one for the Emitter.
2. Refer to
Introduction to Sensor I/O Connectors/Sensor Controllers
for details.
*1. The Sensor can be used in low-temperature environments (−25°C to
−40°C).
Do not use the Sensor in locations that are subject to oil.
*2. The connector will not rotate after connecting.
*3. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface.
4
E3Z
Ratings and Specifications
Sensing method
NPN
Pre-wired
out-
put Connector (M8)
PNP
Pre-wired
out-
put Connector (M8)
E3Z-T61
E3Z-T66
E3Z-T81
E3Z-T86
Through-beam
E3Z-T62
E3Z-T67
E3Z-T82
E3Z-T87
E3Z-T61A
E3Z-T66A
E3Z-T81A
E3Z-T86A
Retro-reflective with
MSR function
E3Z-R61
E3Z-R66
E3Z-R81
E3Z-R86
Diffuse-reflective
E3Z-D61
E3Z-D66
E3Z-D81
E3Z-D86
E3Z-D62
E3Z-D67
E3Z-D82
E3Z-D87
1m
(white paper:
300
×
300 mm)
(Narrow-
beam Models)
E3Z-L61
E3Z-L66
E3Z-L81
E3Z-L86
90 + 30 mm
(white paper,
100 x 100 mm)
(2.5 dia. and
sensing dis-
tance of
90 mm)
---
0.1 mm (cop-
per wire)
20% max. of setting distance
2 to 10°
Red LED (660 nm)
Infrared LED (860 nm)
---
Red LED
(650 nm)
Refer to
Engi-
neering data
on page 8.
Model
Item
Sensing distance
15 m
30 m
10 m
4 m (100 mm)
*1
100 mm
(when using E39-R1S)
(white paper:
3 m (100 mm)
*1
100
×
100 mm)
(when using E39-R1)
Spot diameter (reference value)
---
Standard sensing object
Minimum detectable object
(reference value)
Differential travel
Directional angle
Light source (wavelength)
Current consumption
Opaque: 12-mm dia. min.
Opaque: 75-mm dia. min.
---
---
Both emitter and receiver: 3 to 15°
Infrared LED (870 nm)
Red LED
(660 nm)
35 mA max. (Emitter: 15 mA max., Receiv-
30 mA max.
er: 20 mA max.)
Reversed power supply polarity protection,
Output short-circuit protection, and Re-
versed output polarity protection
Operate or
reset:
1 ms max.
IEC, IP67
Pre-wired cable (standard length: 2 m and 0.5 m), Connector (M8)
Approx. 120 g
Approx. 30 g
PBT (polybutylene terephthalate)
Modified polyarylate
Methacrylic resin
Modified polyarylate
Approx. 65 g
Approx. 20 g
Operate or
reset:
2 ms max.
Reversed power supply polarity protection, Output short-circuit protection,
Mutual interference prevention, and Reversed output polarity protection
Protection circuits
Response time
Degree of protection
Connection method
Weight
(packedstate)
Material
Pre-wired cable (2 m)
Connector
Case
Lens
Operate or reset: 1 ms max.
Sensing method
Item
Model
NPN output
PNP output
E3Z-B61
E3Z-B81
Retro-reflective for clear, plastic bottles (without MSR function)
E3Z-B66
E3Z-B86
E3Z-B62
E3Z-B82
E3Z-B67
E3Z-B87
Sensing distance
Standard sensing object
Light source (wavelength)
Current consumption
Protection circuits
Response time
Degree of protection
Connection method
Weight
(packed
state)
Material
Pre-wired cable (2 m)
Standard Connector
Case
Lens
500 mm (80 mm)
*1
(using E39-R1S)
2 m (500 mm)
*1 *2
(using E39-R1S)
Opaque materials, 75mm dia. min.
(Standard detectable object :glass Cylinder 15mm dia. thickness 1.1mm length 50mm, and the transmis-
[i=s] This post was last edited by paulhyde on 2014-9-15 09:04 [/i] I just drew the ARM schematic. Please help me find out if there is anything wrong with it. Please correct me~! ~...
I saw a good article! Share it with everyone~
The content has been open sourced in LiChuang, open source address: https://oshwhub.com/gnosis/n32g430The ammeter is implemented using the National Techno...
In order to better integrate the first domestically produced PCB——Qingyuefeng Software into the international market, Qingyuefeng Software urgently needs a catchy name. Now we are soliciting English n...
Power supply competition questions have always been a must-have topic in the electrical competition every year. From the previous competition questions, we can see that "power supply" competition ques...
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
On August 25th, SK Hynix announced that it has completed development and entered mass production of its 321-layer, 2Tb QLC NAND flash memory product. This achievement marks the world's first applic...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
A multilevel inverter converts a DC signal into a multilevel staircase waveform. Instead of a straight positive-negative output waveform, the output waveform of a multilevel inverter alternates in ...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
Magna's integrated in-cabin perception system fuses vision and millimeter-wave radar data to detect the presence of passengers, identify stranded children, monitor driver fatigue and vital signs, a...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
Traditionally, electrical energy is transmitted primarily through wires, requiring direct physical contact between the power source and the load. With the increasing number of electrical devices in...[Details]
At present, the most troubling thing about pure electric vehicles as new energy sources is not only the range anxiety, but also the disadvantage of long charging time. At present, ternary lithium b...[Details]
The power transmission system between a car's engine and drive wheels is called its drivetrain. It ensures the necessary traction and speed under various driving conditions, and coordinates these t...[Details]
Robotics Development
京公网安备 11010802033920号
EEWORLD
