The Reflector is sold separately. Select the Reflector model most suited to the application.
The sensing distance specified is possible when the E39-R1S is used.
Values
in parentheses indicate the minimum required distance between the Sensor and Reflector.
Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver.
M12 Standard Pre-wired Connector Models are also availavble.
When ordering, add "-M1J 0.3M" to the end of the model number (e.g., E3Z-T61-M1J 0.3M).
The cable is 0.3 m long.
Accessories (Order Separately)
Slit
(A Slit is not provided with Through-beam Sensors) Order a Slit separately if required.
[Refer to
Dimensions
on page 16.]
Slit width
0.5-mm dia.
1-mm dia.
2-mm dia.
0.5
×
10 mm
1
×
10 mm
2
×
10 mm
Sensing distance
E3Z-T@@
E3Z-T@@A
50 mm
35 mm
200 mm
150 mm
800 mm
550 mm
1m
700 mm
2.2 m
1.5 m
5m
3.5 m
Minimum detectable object
(Reference value)
0.2-mm dia.
0.4-mm dia.
0.7-mm dia.
0.2-mm dia.
0.5-mm dia.
0.8-mm dia.
Model
E39-S65A
E39-S65B
E39-S65C
E39-S65D
E39-S65E
E39-S65F
Contents
One set
(contains Slits for
both the Emitter and
Receiver)
Reflectors
(Reflector required for Retroreflective Sensors) A Reflector is not provided with the Sensor. Be sure to order a Reflector separately.
[Refer to
Dimensions
on
E39-L/E39-S/E39-R]
Sensing distance
*
E3Z-R
E3Z-R@K
E3Z-B@1/-B@6
Reference value
Rated value
(sensing
(sensing
Rated value
Rated value
distance of 15 m) distance of 10 m)
---
---
3 m (100 mm)
2 m (100 mm)
---
4 m (100 mm)
3 m (150 mm)
500 mm (80 mm)
---
---
---
5 m (100 mm)
---
---
---
2.5 m (100 mm)
---
---
---
3.5 m(100 mm)
---
E3Z-B@2/-B@7
Model
Rated value
---
Name
Quantity
Remarks
2 m (500 mm)
---
---
---
Reflector
E39-R1
E39-R1S
E39-R2
E39-R9
E39-R10
E39-R1K
1
1
1
1
1
1
---
---
---
---
1.5 m (50 mm)
E39-R3
1
---
---
---
---
700 mm (150 mm)
E39-RS1
1
---
---
---
---
Tape Reflector
1.1 m (150 mm)
E39-RS2
1
---
---
---
---
1.4 m (150 mm)
E39-RS3
1
Note: 1. If you use the Reflector at any distance other than the rated distance, make sure that the stability indicator lights properly when you install the Sensor.
2. Refer to
Reflectors
on
E39-L/E39-S/E39-R
for details.
*
Values
in parentheses indicates the minimum required distance between the Sensor and Reflector.
Fog Preventive
Coating
Small Reflector
3 m (100 mm)
---
500 mm (80 mm)
2 m (500 mm)
•
Retro-reflective
models are not
provided with
Reflectors.
•
The MSR function
is enabled.
Mutual Interference Protection Filter
A Filter is not provided with the Sensor (for the through-beam E3Z-T@@A). Order a Filter separately if required.
Sensing distance
Appearance/Dimensions
10.8
7.4
4.9
1
Model
Quantity
Remarks
Can be used with the E3Z-T@@A Through-
beam models. The arrow indicates the direc-
tion of polarized light. Mutual interference
can be prevented by altering the direction of
polarized light from or to adjacent Emitters
and Receivers.
3m
31.4 11.2
0.2
E39-E11
Two sets each for the
Emitter and Receiver
(total of four pieces)
Note: The polarization directions of the Filters are offset by 90º to prevent interference. When you install the Emitter and Receiver, install them at the same angle to
maintain this offset.
3
E3Z
Mounting Brackets
A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
[Refer to
Dimensions
on
E39-L/E39-S/E39-R]
Appearance
Model (material)
E39-L153
(SUS304)
*1
Quantity
Remarks
Appearance
Model (material)
E39-L98
(SUS304)
*2
Mounting Brackets
E39-L104
(SUS304)
*1
1
E39-L150
(SUS304)
1
(Sensor adjuster)
Easily mounted to the
aluminum frame rails of
conveyors and easily
adjusted.
E39-L151
(SUS304)
E39-L142
(SUS304)
*2
1
Horizontal Protective
Cover Bracket
1
For left to right adjust-
ment
Quantity
Remarks
Metal Protective Cover
Bracket
1
1
E39-L43
(SUS304)
*2
1
Horizontal Mounting
Brackets
E39-L44
(SUS304)
1
Rear Mounting Bracket
E39-L144
(SUS304)
*2
1
Compact Protective
Cover Bracket (For E3Z
only)
Note: 1. When using Through-beam models, order one bracket for the Receiver and one for the Emitter.
2. Refer to
Mounting Brackets
on
E39-L/E39-S/E39-R
for details.
*1. Cannot be used for Standard Connector models with mounting surface on the bottom. In that case, use Pre-wired Connector models.
*2. Cannot be used for Standard Connector models.
Sensor I/O Connectors (Sockets on One Cable End)
(Models for Connectors and Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
[Refer to
Dimensions
for
XS3.]
Size
Cable
Straight
*2
Standard
L-shaped
*2 *3
PUR
(Polyure-
thane) cable
*1
Straight
*2
L-shaped
*2 *3
Straight
*2
L-shaped
*2 *3
Appearance
Cable type
2m
5m
2m
5m
2m
5m
2m
5m
2m
5m
2m
5m
4-wire
Model
XS3F-M421-402-A
XS3F-M421-405-A
XS3F-M422-402-A
XS3F-M422-405-A
XS3F-M421-402-L
XS3F-M421-405-L
XS3F-M422-402-L
XS3F-M422-405-L
XS3F-M421-402-R
XS3F-M421-405-R
XS3F-M422-402-R
XS3F-M422-405-R
M8
Vibration-proof
robot cable
Note: 1. When using Through-beam models, order one connector for the Receiver and one for the Emitter.
2. Refer to
Introduction to Sensor I/O Connectors/Sensor Controllers
for details.
*1. The Sensor can be used in low-temperature environments (−25°C to
−40°C).
Do not use the Sensor in locations that are subject to oil.
*2. The connector will not rotate after connecting.
*3. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface.
4
E3Z
Ratings and Specifications
Sensing method
NPN
Pre-wired
out-
put Connector (M8)
PNP
Pre-wired
out-
put Connector (M8)
E3Z-T61
E3Z-T66
E3Z-T81
E3Z-T86
Through-beam
E3Z-T62
E3Z-T67
E3Z-T82
E3Z-T87
E3Z-T61A
E3Z-T66A
E3Z-T81A
E3Z-T86A
Retro-reflective with
MSR function
E3Z-R61
E3Z-R66
E3Z-R81
E3Z-R86
Diffuse-reflective
E3Z-D61
E3Z-D66
E3Z-D81
E3Z-D86
E3Z-D62
E3Z-D67
E3Z-D82
E3Z-D87
1m
(white paper:
300
×
300 mm)
(Narrow-
beam Models)
E3Z-L61
E3Z-L66
E3Z-L81
E3Z-L86
90 + 30 mm
(white paper,
100 x 100 mm)
(2.5 dia. and
sensing dis-
tance of
90 mm)
---
0.1 mm (cop-
per wire)
20% max. of setting distance
2 to 10°
Red LED (660 nm)
Infrared LED (860 nm)
---
Red LED
(650 nm)
Refer to
Engi-
neering data
on page 8.
Model
Item
Sensing distance
15 m
30 m
10 m
4 m (100 mm)
*1
100 mm
(when using E39-R1S)
(white paper:
3 m (100 mm)
*1
100
×
100 mm)
(when using E39-R1)
Spot diameter (reference value)
---
Standard sensing object
Minimum detectable object
(reference value)
Differential travel
Directional angle
Light source (wavelength)
Current consumption
Opaque: 12-mm dia. min.
Opaque: 75-mm dia. min.
---
---
Both emitter and receiver: 3 to 15°
Infrared LED (870 nm)
Red LED
(660 nm)
35 mA max. (Emitter: 15 mA max., Receiv-
30 mA max.
er: 20 mA max.)
Reversed power supply polarity protection,
Output short-circuit protection, and Re-
versed output polarity protection
Operate or
reset:
1 ms max.
IEC, IP67
Pre-wired cable (standard length: 2 m and 0.5 m), Connector (M8)
Approx. 120 g
Approx. 30 g
PBT (polybutylene terephthalate)
Modified polyarylate
Methacrylic resin
Modified polyarylate
Approx. 65 g
Approx. 20 g
Operate or
reset:
2 ms max.
Reversed power supply polarity protection, Output short-circuit protection,
Mutual interference prevention, and Reversed output polarity protection
Protection circuits
Response time
Degree of protection
Connection method
Weight
(packedstate)
Material
Pre-wired cable (2 m)
Connector
Case
Lens
Operate or reset: 1 ms max.
Sensing method
Item
Model
NPN output
PNP output
E3Z-B61
E3Z-B81
Retro-reflective for clear, plastic bottles (without MSR function)
E3Z-B66
E3Z-B86
E3Z-B62
E3Z-B82
E3Z-B67
E3Z-B87
Sensing distance
Standard sensing object
Light source (wavelength)
Current consumption
Protection circuits
Response time
Degree of protection
Connection method
Weight
(packed
state)
Material
Pre-wired cable (2 m)
Standard Connector
Case
Lens
500 mm (80 mm)
*1
(using E39-R1S)
2 m (500 mm)
*1 *2
(using E39-R1S)
Opaque materials, 75mm dia. min.
(Standard detectable object :glass Cylinder 15mm dia. thickness 1.1mm length 50mm, and the transmis-
I did a test. Without an operating system, I configured the DMA special registers and used the burst mode. It took about 2.4 microseconds to read and write 16 bytes. However, with a Linux system, I wr...
When using Windml5.2 library to compile vxworks image, the following error occurs: warning: Undefined symbol 'uglIoDrvInit' in file 'partialImage.o' dld: warning: Undefined symbol 'uglSdkArray' in fil...
[size=3]Simple and crude, just post the pictures:Mad:[/size] [b][size=3]The following pictures are in Changsha, Hunan[/size][/b][b][size=3] [/size][/b][b][size=3]The following pictures are in Hengyang...
STMicroelectronics (ST) has launched samples and reference design boards for its ST20190 Utopia ADSL2+ products. This chipset allows designers of ODMs (original design manufacturers) and AOMs to addre...
Flip-chip and ball grid array (BGA) are two widely used packaging technologies in the electronics industry. Each has its own advantages and limitations, and in some cases, they can complement each ...[Details]
On August 25th, TSMC, the world's leading contract chip manufacturer, attracted significant attention for its decision to build a chip manufacturing facility in Arizona. TSMC primarily manufactures...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
According to foreign media reports, BMW has just been granted a patent for a screen that could cover the entire roof. BMW hopes to transform at least a portion of the vehicle's headliner into a dis...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
Learned the following information.
Customer product: industrial computer motherboard
Glue application area: CPU/BGA filling
Glue color requirements: black or t...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
Recently, Joyson Electronics has made positive progress in the core technology research and development of the robot's "brain and brain" and key components, and launched the industry's first integr...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
Puttshack's Trackaball uses the Nordic nRF54L15 system-on-chip (SoC) to monitor sensors and enable Bluetooth low energy connectivity, while the nPM2100 power management integrated circuit (PMIC) ...[Details]
Introduction: In digital circuit calculations, there is no concept of decimal points. You know where the decimal is, but the circuit does not know where the decimal point is. Therefore, you need to...[Details]
On August 20, it was reported that the specifications of Intel's upcoming Panther Lake mobile processor appeared on the Intel GFX CI website, which mainly focuses on Intel's open source Linux drive...[Details]
The Radxa Cubie A7A is a single-board computer (SBC) powered by the Allwinner A733 octa-core Cortex-A76/A55 SoC, equipped with a 3 TOPS AI accelerator and up to 16GB of LPDDR5 memory.
Fo...[Details]
The power transmission system between a car's engine and drive wheels is called its drivetrain. It ensures the necessary traction and speed under various driving conditions, and coordinates these t...[Details]
Linux and Android
京公网安备 11010802033920号
EEWORLD
