in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.
DS312 July 19, 2013
Product Specification
www.xilinx.com
1
8
Spartan-3E FPGA Family:
Introduction and Ordering Information
Product Specification
DS312 (v4.1) July 19, 2013
Introduction
The Spartan®-3E family of Field-Programmable Gate
Arrays (FPGAs) is specifically designed to meet the needs
of high volume, cost-sensitive consumer electronic
applications. The five-member family offers densities
ranging from 100,000 to 1.6 million system gates, as shown
in
Table 1.
The Spartan-3E family builds on the success of the earlier
Spartan-3 family by increasing the amount of logic per I/O,
significantly reducing the cost per logic cell. New features
improve system performance and reduce the cost of
configuration. These Spartan-3E FPGA enhancements,
combined with advanced 90 nm process technology, deliver
more functionality and bandwidth per dollar than was
previously possible, setting new standards in the
programmable logic industry.
Because of their exceptionally low cost, Spartan-3E FPGAs
are ideally suited to a wide range of consumer electronics
applications, including broadband access, home
networking, display/projection, and digital television
equipment.
The Spartan-3E family is a superior alternative to mask
programmed ASICs. FPGAs avoid the high initial cost, the
lengthy development cycles, and the inherent inflexibility of
in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.
DS312 (v4.1) July 19, 2013
Product Specification
www.xilinx.com
2
Spartan-3E FPGA Family: Introduction and Ordering Information
Architectural Overview
The Spartan-3E family architecture consists of five
fundamental programmable functional elements:
•
Configurable Logic Blocks (CLBs)
contain flexible
Look-Up Tables (LUTs) that implement logic plus
storage elements used as flip-flops or latches. CLBs
perform a wide variety of logical functions as well as
store data.
Input/Output Blocks (IOBs)
control the flow of data
between the I/O pins and the internal logic of the
device. Each IOB supports bidirectional data flow plus
3-state operation. Supports a variety of signal
standards, including four high-performance differential
standards. Double Data-Rate (DDR) registers are
included.
Block RAM
provides data storage in the form of
18-Kbit dual-port blocks.
Multiplier Blocks
accept two 18-bit binary numbers as
inputs and calculate the product.
•
Digital Clock Manager (DCM) Blocks
provide
self-calibrating, fully digital solutions for distributing,
delaying, multiplying, dividing, and phase-shifting clock
signals.
•
These elements are organized as shown in
Figure 1.
A ring
of IOBs surrounds a regular array of CLBs. Each device has
two columns of block RAM except for the XC3S100E, which
has one column. Each RAM column consists of several
18-Kbit RAM blocks. Each block RAM is associated with a
dedicated multiplier. The DCMs are positioned in the center
with two at the top and two at the bottom of the device. The
XC3S100E has only one DCM at the top and bottom, while
the XC3S1200E and XC3S1600E add two DCMs in the
middle of the left and right sides.
The Spartan-3E family features a rich network of traces that
interconnect all five functional elements, transmitting
signals among them. Each functional element has an
associated switch matrix that permits multiple connections
to the routing.
•
•
X-Ref Target - Figure 1
Figure 1:
Spartan-3E Family Architecture
DS312 (v4.1) July 19, 2013
Product Specification
www.xilinx.com
3
Spartan-3E FPGA Family: Introduction and Ordering Information
Configuration
Spartan-3E FPGAs are programmed by loading
configuration data into robust, reprogrammable, static
CMOS configuration latches (CCLs) that collectively control
all functional elements and routing resources. The FPGA’s
configuration data is stored externally in a PROM or some
other non-volatile medium, either on or off the board. After
applying power, the configuration data is written to the
FPGA using any of seven different modes:
•
•
•
•
•
•
Master Serial from a Xilinx Platform Flash PROM
Serial Peripheral Interface (SPI) from an
industry-standard SPI serial Flash
Byte Peripheral Interface (BPI) Up or Down from an
industry-standard x8 or x8/x16 parallel NOR Flash
Slave Serial, typically downloaded from a processor
Slave Parallel, typically downloaded from a processor
Boundary Scan (JTAG), typically downloaded from a
processor or system tester.
I/O Capabilities
The Spartan-3E FPGA SelectIO interface supports many
popular single-ended and differential standards.
Table 2
shows the number of user I/Os as well as the number of
differential I/O pairs available for each device/package
combination.
Spartan-3E FPGAs support the following single-ended
standards:
•
•
•
•
•
3.3V low-voltage TTL (LVTTL)
Low-voltage CMOS (LVCMOS) at 3.3V, 2.5V, 1.8V,
1.5V, or 1.2V
3V PCI at 33 MHz, and in some devices,
66 MHz
HSTL I and III at 1.8V, commonly used in memory
applications
SSTL I at 1.8V and 2.5V, commonly used for memory
applications
Spartan-3E FPGAs support the following differential
standards:
•
•
•
•
•
•
•
LVDS
Bus LVDS
mini-LVDS
RSDS
Differential HSTL (1.8V, Types I and III)
Differential SSTL (2.5V and 1.8V, Type I)
2.5V LVPECL inputs
Furthermore, Spartan-3E FPGAs support MultiBoot
configuration, allowing two or more FPGA configuration
bitstreams to be stored in a single parallel NOR Flash. The
FPGA application controls which configuration to load next
and when to load it.
Table 2:
Available User I/Os and Differential (Diff) I/O Pairs
Package
Footprint
Size (mm)
Device
XC3S100E
XC3S250E
XC3S500E
XC3S1200E
XC3S1600E
Notes:
1.
2.
3.
All Spartan-3E devices provided in the same package are pin-compatible as further described in Module 4,
Pinout Descriptions.
The number shown in
bold
indicates the maximum number of I/O and input-only pins. The number shown in (italics) indicates the number
of input-only pins.
The XC3S500E is available in the VQG100 Pb-free package and not the standard VQ100. The VQG100 and VQ100 pin-outs are identical
and general references to the VQ100 will apply to the XC3S500E.
VQ100
VQG100
16 x 16
User
66
(2)
9(7)
66
(7)
66
(3)
(7)
-
-
Diff
30
(2)
30
(2)
30
(2)
-
-
CP132
CPG132
8x8
User
83
(11)
92
(7)
92
(7)
-
-
Diff
35
(2)
41
(2)
41
(2)
-
-
TQ144
TQG144
22 x 22
User
108
(28)
108
(28)
-
-
-
Diff
40
(4)
40
(4)
-
-
-
PQ208
PQG208
30.5 x 30.5
User
-
158
(32)
158
(32)
-
-
Diff
-
65
(5)
65
(5)
-
-
FT256
FTG256
17 x 17
User
-
172
(40)
190
(41)
190
(40)
-
Diff
-
68
(8)
77
(8)
77
(8)
-
FG320
FGG320
19 x 19
User
-
-
232
(56)
250
(56)
250
(56)
Diff
-
-
92
(12)
99
(12)
99
(12)
FG400
FGG400
21 x 21
User
-
-
-
304
(72)
304
(72)
Diff
-
-
-
124
(20)
124
(20)
FG484
FGG484
23 x 23
User
-
-
-
-
376
(82)
Diff
-
-
-
-
156
(21)
DS312 (v4.1) July 19, 2013
Product Specification
www.xilinx.com
4
Spartan-3E FPGA Family: Introduction and Ordering Information
Package Marking
Figure 2
provides a top marking example for Spartan-3E
FPGAs in the quad-flat packages.
Figure 3
shows the top
marking for Spartan-3E FPGAs in BGA packages except
the 132-ball chip-scale package (CP132 and CPG132). The
markings for the BGA packages are nearly identical to those
for the quad-flat packages, except that the marking is
rotated with respect to the ball A1 indicator.
Figure 4
shows
the top marking for Spartan-3E FPGAs in the CP132 and
CPG132 packages.
X-Ref Target - Figure 2
On the QFP and BGA packages, the optional numerical
Stepping Code follows the Lot Code.
The “5C” and “4I” part combinations can have a dual mark
of “5C/4I”. Devices with a single mark are only guaranteed
for the marked speed grade and temperature range. All “5C”
and “4I” part combinations use the Stepping 1 production
silicon.
Mask Revision Code
Fabrication Code
R
SPARTAN
Device Type
Package
Speed Grade
Temperature Range
TM
R
Process Technology
Date Code
Stepping Code
(optional)
Lot Code
XC3S250E
PQ208AGQ0525
D1234567A
4C
Pin P1
DS312-1_06_102905
Figure 2:
Spartan-3E QFP Package Marking Example
X-Ref Target - Figure 3
Mask Revision Code
BGA Ball A1
Device Type
Package
R
SPARTAN
R
Fabrication Code
Process Code
XC3S250E
TM
FT256AGQ0525
D1234567A
4C
Date Code
Stepping Code
(optional)
Lot Code
Speed Grade
Temperature Range
DS312-1_02_090105
Figure 3:
Spartan-3E BGA Package Marking Example
X-Ref Target - Figure 4
Ball A1
Lot Code
3S250E
F1234567-0525
PHILIPPINES
Device Type
Date Code
Temperature Range
Package
C5 = CP132
C6 = CPG132
C5AGQ
4C
Speed Grade
Process Code
Fabrication Code
DS312-1_05_032105
Mask Revision Code
Figure 4:
Spartan-3E CP132 and CPG132 Package Marking Example
I am a newcomer and not very familiar with the use of Freescale microcontrollers. Recently, I have been using Freescale 128 microcontrollers and nrf905 to make a small wireless transmission protocol. ...
Can the output value of a non-inverting or inverting proportional operational amplifier composed of an operational amplifier not match the supply voltage?...
Request to continue group buying MSP430 LaunchPad MSP-EXP430G2 25 yuan without shipping, 30 yuan is also OK [[i] This post was last edited by ppiicc on 2012-5-3 22:53 [/i]]...
This verifies the importance and convenience of radio electromagnetic waves. We must study whether this thing can record data accurately.Satellite distance recordAO-40 (USA/USA) – 18,730 km. ZL1AOX in...
Dedicated to our friends in the electronics industry, don't just focus on R&D and coding, take some time to learn [flash=500,500]http://player.ku6.com/refer/TDf56AAyrxDS8zrdYFhpIQ../v.swf[/flash][medi...
[i=s]This post was last edited by wugx on 2016-7-27 17:54[/i] The project has started to be conceived again, which is probably about data collection, storage, analysis and statistics, display, etc. Th...
Current Development Status of DVR Market
A DVR, or digital video recorder, uses a hard disk for recording, unlike traditional analog video recorders. It's often called a DVR because it's a com...[Details]
1 Introduction
In the mid-1960s, American scientist Maas conducted extensive experimental research on the charging process of open-cell batteries and proposed an acceptable charging curve for ...[Details]
1. Fault phenomenon and cause analysis
1. During the operation of the equipment, the expansion sleeve is subjected to a large torque, and the mating surfaces of the shaft and the sleeve move...[Details]
On August 20, Geely announced its focus on "One Cockpit". Through a unified AI OS architecture, a unified AI Agent, and a unified user ID, it will achieve an All-in-One AI cockpit, create the first...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
In the field of communications power supplies, AC/DC rectifier power supplies are called primary power supplies or basic power supplies, while DC/DC converters are called secondary power supplies. ...[Details]
01. Introduction
As in-vehicle networks migrate from the CAN
bus
to
Ethernet
, traditional millisecond-level synchronization accuracy can no longer meet the requirements of mul...[Details]
0 Introduction
With a rapidly aging population, a young couple is now required to care for an increasing number of elderly people, leading to a growing difficulty in providing care for them. E...[Details]
As the electric vehicle industry continues to surge in today's society, while people are concerned about the appearance and interior of new energy vehicles, they are also concerned about the classi...[Details]
We know that the power output by the engine does not directly act on the wheels to drive the car, but needs to pass through a series of power transmission mechanisms. So how is the power transmitte...[Details]
While aberration theory is a vast subject, a basic understanding of some fundamental concepts can make it easier to understand: spherical aberration, astigmatism, field curvature, and chromatic abe...[Details]
Industrial equipment plays a significant role in improving industrial automation and accelerating production efficiency. Industrial HMIs (Human-Machine Interfaces) serve as a communication platform...[Details]
Abstract: This design uses field-effect transistors to create a tube-like audio power amplifier. The preamplifier uses a single Class A transistor, while the power stage utilizes Class AB push-pull...[Details]
On August 18, domestic EDA manufacturer HuaDa JiuTian launched the advanced packaging design platform Storm for the first time in the world at the end of July. It claims that the chiplet wiring eff...[Details]
Security Use Cases and Implementation: Ensuring Future Security
By Manoj Rajashekarah, Chief
summary
In our previous article, "Securing the Future of Robotics: The Role of Cy...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
