Technical Data
August 2014
3M
™
Low Static Polyimide Film Tape 7419
Product Description
3M™ Low Static, Non-Silicone Polyimide Film Tape 7419 with DuPont™ Kapton
®
polyimide film and acrylic adhesive is
amber-colored and used for PCB solder masking and other high temperature applications.
Features and Benefits
• Specially formulated acrylic adhesive is resistant to typical solder mask temperatures for short periods of time.
Stays firmly in place during processing and removes cleanly from typical electronic substrates even after 10 min
@ 260°C (500°F).
• Non-silicone adhesive formulation lessens the potential for silicone contamination which can interfere with
subsequent bonding or conformal coating operations.
• The high temperature acrylic adhesive also has excellent chemical resistance and should be considered for
demanding chemical masking applications.
• Product is wound on a polyethylene tape core.
Product Construction/Material Description
3M™ Low Static Polyimide Film Tape 7419
Color
Backing
Adhesive
Standard Roll Length
Amber
Dupont™ Kapton
®
Polyimide Film
Acrylic
33 m (36 yd)
Applications
• Masking or protecting residue sensitive areas on printed circuit boards during high temperature operations such
as wave soldering and solder reflow.
3M
™
Low Static Polyimide Film Tape 7419
Typical Physical Properties
Note:
The following technical information and data should be considered representative or typical only, and should not
be used for specification purposes.
3M™ Low Static Polyimide Film Tape 7419
Property
Adhesion to Steel
Initial
72 hrs @ Room Temp
10 min @ 260°C
Adhesion to Copper
Initial
72 hrs @ Room Temp
10 min @ 260°C
Backing Thickness
Total Tape Thickness
Static Discharge
Removal from roll
Dielectric Strength
Surface Resistivity
Temperature Use Range*
Method
D-3330, Part A
4 oz/in width (4.52 N/100 mm)
5 oz/in width (5.65 N/100 mm)
17 oz/in width (19 N/100 mm)
D-3330, Part A
4 oz/in width (4.52 N/100 mm)
5 oz/in width (5.65 N/100 mm)
10 oz/in width (11 N/100 mm)
D-3652
D-3652
—
—
ESD Method S-11
—
1.0 mil (0.025 mm)
1.8 mil (0.046 mm)
< 100 volts
6000 volts
5 x 10
6
ohms/sq
10 min at 260°C
Value
*
Temperature use range is defined as the maximum time at the stated temperature after which the 3M tape 7419 may be removed cleanly,
without staining, from a copper substrate.
General Information
• Splice-free maximum roll length is 36.1 yd -0/+.2 yd (33 m -0/+2 m).
• Typical slit roll width tolerance: target ± .031 in (± 0.8 mm).
• Product provided on plastic polyethylene cores and individually packed.
Core ID = 3.020 in ± .004 in (76.7 mm ± 0.1 mm).
• Substrate should be smooth, clean, dry and oil-free to ensure good wet-out and adequate adhesion.
• Tape may not bond or conform to low surface energy, rough or sharply curved surfaces.
Storage and Shelf Life
To obtain best performance, use this product within 18 months from date of delivery and store under normal conditions
of 16° to 27°C (60° to 80°F) and 40 to 60% relative humidity in the original carton.
(2)
3M
™
Low Static Polyimide Film Tape 7419
Safety Data Sheet
Consult Safety Data Sheet before use.
Regulatory
For regulatory information about this product, contact your 3M representative.
Technical Information
The technical information, recommendations and other statements contained in this document are based upon tests
or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed.
Product Use
Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance
of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M
product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose
and suitable for user’s method of application.
Warranty, Limited Remedy, and Disclaimer
Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature,
3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product.
3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED
WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M product
does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product
or refund of the purchase price.
Limitation of Liability
Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether
direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract,
negligence or strict liability.
Electronics Materials Solutions Division
3M Center, Building 225-3S-06
St. Paul, MN 55144-1000
1-800-251-8634 phone
651-778-4244 fax
www.3M.com/electronics
DuPont™ and Kapton
®
are trademarks of E. I. du Pont
de Nemours and Company or its affiliates.
3M is a trademark of 3M Company.
Please recycle.
© 3M 2014. All rights reserved.
60-5002-0112-8
(3)
Embedded System
京公网安备 11010802033920号
EEWORLD
