EEWORLDEEWORLDEEWORLD

Part Number

Search

SIT9005ACT7D-25EE

Description
OSC MEMS
CategoryPassive components   
File Size333KB,9 Pages
ManufacturerSiTime
Environmental Compliance
Download Datasheet Parametric View All

SIT9005ACT7D-25EE Overview

OSC MEMS

SIT9005ACT7D-25EE Parametric

Parameter NameAttribute value
typeSSXO MEMS
Programmable typeProgrammed by Digi-Key (please enter your desired frequency on the website order form)
Available frequency range1MHz ~ 141MHz
Functionenable/disable
outputLVCMOS
Voltage - Power2.5V
frequency stability±20ppm,±25ppm,±50ppm
Frequency stability (overall)-
Operating temperature-20°C ~ 70°C
spread spectrum bandwidth-1.29%, Down Spread
Current - Power (maximum)6.5mA
grade-
Installation typesurface mount
Package/casing4-SMD, no leads
size/dimensions0.079" long x 0.063" wide (2.00mm x 1.60mm)
high0.030"(0.76mm)
Current - Power (disabled) (maximum)6.5mA
SiT9005
1 to 141 MHz EMI Reduction Oscillator
Features
Applications
Spread spectrum for EMI reduction
Wide spread % option
Center spread: from ±0.125% to ±2%, ±0.125% step size
Down spread: -0.25% to -4% with -0.25% step size
Spread profile option: Triangular, Hershey-kiss
Programmable rise/fall time for EMI reduction: 8 options,
0.25 to 40 ns
Any frequency between 1 MHz and 141 MHz accurate to
6 decimal places
100% pin-to-pin drop-in replacement to quartz-based XO’s
Excellent total frequency stability as low as ±20 ppm
Operating temperature from -40°C to 85°C.
Low power consumption of 4.0 mA typical at 1.8V
Pin1 modes: Standby, output enable, or spread disable
Fast startup time of 5 ms
LVCMOS output
Industry-standard packages
QFN: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5 mm
2
Contact
SiTime
for SOT23-5 (2.9 x 2.8 mm
2
)
RoHS and REACH compliant, Pb-free, Halogen-free
and Antimony-free
Surveillance camera
IP camera
Industrial motors
Flat panels
Multi function printers
PCI express
Electrical Specifications
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
Typical values are at 25°C and 3.3V supply voltage.
Parameters
Output Frequency Range
Symbol
Min.
Typ.
Max.
Unit
Condition
Frequency Range
f
1
141
MHz
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-50
Operating Temperature Range
T_use
-20
-40
Supply Voltage
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
OE Disable Current
Idd
I_OD
Standby Current
I_std
1.8
2.5
2.8
3.0
3.3
5.6
5.0
5.0
4.6
2.1
0.4
+20
+25
+50
+70
+85
1.98
2.75
3.08
3.3
3.63
3.63
6.5
5.5
6.5
5.2
4.3
1.5
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
µA
µA
No load condition, f = 40 MHz, Vdd = 2.5V to 3.3V
No load condition, f = 40 MHz, Vdd = 1.8V
f = 40 MHz, Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z
state
f = 40 MHz, Vdd = 1.8V, OE = GND, Output in high-Z state
ST
= GND, Vdd = 2.5V to 3.3V, Output is weakly pulled down
ST
= GND, Vdd = 1.8V, Output is weakly pulled down
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage. Spread = Off.
Operating Temperature Range
Extended Commercial
Industrial
Supply Voltage and Current Consumption
Rev 1.0
September 25, 2017
www.sitime.com
ESP8266 fixed the bug of GPIO16 as input
The ESP8266 version has just fixed a bug, when GPIO16 is used as input, it will not be able to read the GPIO status correctly. However, GPIO16 still cannot be set to pull up....
dcexpert MicroPython Open Source section
Are the transmitting frequency 315M and the carrier frequency 38KHZ the same?
Why is the transmission frequency of some remote controls 315M, while the carrier frequency of NEC-coded remote controls is 38KHZ? Are these two concepts the same? Also, how many categories are remote...
hu柏拉图的永恒 51mcu
How to draw components on the back side of the PCB board?
I am drawing a four-layer board. The board is too small and the circuits cannot be completed. How can I draw the components on the back of the board?...
aixuexi呀呀呀呀 PCB Design
Recommended books on embedded development (Part 29) --- Embedded system development based on state machine
[align=center][size=5][b]Recommendations for high-quality books on embedded development (Twenty-nine) ---[color=#666666][font=Helvetica]Embedded system development based on state machine[/font][/color...
tiankai001 Download Centre
C2000 target board hardware troubleshooting steps
[i=s]This post was last edited by Jacktang on 2018-6-20 21:09[/i] [size=5]a. Check whether the emulator is properly plugged in;[/size] [size=5]b. Check the CPU power supply problem, whether the 1.8V a...
Jacktang Microcontroller MCU
The difference between current source, constant current source and DC source
1: What are the differences between current source, constant current source and DC source? 2: Is the square wave above the X-axis considered a constant current source?...
electrics Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1818  2111  2415  1638  1540  37  43  49  33  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号