No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condition, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V, 3.3V, ST = GND, output is Weakly Pulled Down
Vdd = 1.8V, ST = GND, output is Weakly Pulled Down
See the Absolute Pull Range and APR table on
page 10
Vdd = 1.8V, Voltage at which maximum deviation is guaranteed.
Vdd = 2.5V, Voltage at which maximum deviation is guaranteed.
Vdd = 2.8V, Voltage at which maximum deviation is guaranteed.
Vdd = 3.3V, Voltage at which maximum deviation is guaranteed.
Voltage at which minimum deviation is guaranteed.
Additional supply voltages between 2.5V and 3.3V can be
supported. Contact
SiTime
for additional information.
Condition
Refer to
Table 11
for the exact list of supported frequencies
Inclusive of Initial tolerance
[4]
at 25 °C, and variation over
temperature, rated supply voltage and load.
10 years, 25°C
Extended Commercial
Industrial
Frequency Range
Frequency Stability and Aging
Supply Voltage and Current Consumption
VCXO Characteristics
±25, ±50, ±100, ±150, ±200
1.7
2.4
2.7
3.2
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Capacitance
Linearity
Frequency Change Polarity
Control Voltage Bandwidth (-3dB)
Duty Cycle
Rise/Fall Time
Output High Voltage
VC_L
Z_in
C_in
Lin
–
V_BW
DC
Tr, Tf
VOH
–
45
–
90%
–
100
–
–
–
–
–
–
–
–
5
0.1
Positive slope
8
–
1.5
–
–
–
–
–
0.1
–
–
1
Upper Control Voltage
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
SiTime Corporation
Rev. 1.01
990 Almanor Avenue, Sunnyvale, CA 94085
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 1. Electrical Characteristics
[1, 2, 3]
Parameter
Input Pull-up Impedance
Input Capacitance
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
RMS Phase Jitter (random)
Symbol
Z_in
C_in
T_start
T_oe
T_resume
T_jitt
T_phj
Electrical Specifications
(continued)
Min.
–
–
–
–
–
–
–
–
Typ.
100
5
–
–
7
1.5
2
0.5
Max.
250
–
10
180
10
Jitter
2
3
1
ps
ps
ps
f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 20 MHz, Vdd = 1.8V
f = 20 MHz, Integration bandwidth = 12 kHz to 20 MHz, All Vdds
Unit
kΩ
PF
ms
ns
ms
Condition
For the OE/ST pin for 6-pin devices
For the OE/ST pin for 6-pin devices
See Figure 7 for startup resume timing diagram
f = 40 MHz, all Vdds. For other freq, T_oe = 100 ns + 3 clock
periods
See Figure 8 for resume timing diagram
Input Characteristics
Startup and Resume Timing
Notes:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
2. The typical value of any parameter in the Electrical Characteristics table is specified for the nominal value of the highest voltage option for that parameter and at
25 °C temperature.
3. All max and min specifications are guaranteed across rated voltage variations and operating temperature ranges, unless specified otherwise
4. Initial tolerance is measured at Vin = Vdd/2
5. Absolute Pull Range (APR) is defined as the guaranteed pull range over temperature and voltage.
6. APR = pull range (PR) - frequency stability (F_stab) - Aging (F_aging)
Rev. 1.01
Page 2 of 11
www.sitime.com
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 2. Pin Description. 4-Pin Configuration
(For 2.5 x 2.0 mm and 3.2 x 2.5 mm packages)
Pin
1
2
3
4
Symbol
VIN
GND
CLK
VDD
Input
Power
Power
Input
Power
Electrical ground
Power supply voltage
Oscillator output power
[7]
GND
2
3
Top View
Functionality
VIN
1
4
0-Vdd: produces voltage dependent frequency change
VDD
CLK
Note:
7. A capacitor value of 0.1 µF between VDD and GND is recommended.
Figure 1.
Table 3. Pin Description. 6-Pin Configuration
(For 5.0 x 3.2 mm and 7.0 x 5.0 mm packages)
Pin
1
Symbol
VIN
Input
No
Connect
2
NC/OE/ ST
Output
Enable
Standby
3
4
5
6
GND
CLK
NC
VDD
Power
Output
No
Connect
Power
Functionality
0-Vdd: produces voltage dependent frequency change
H or L or Open: No effect on output frequency or other device
functions
H or Open
[8]
: specified frequency output
L: output is high
H or Open
[8]
: specified frequency output
L: output is low (weak pull down)
[9]
. Oscillation stops
Electrical ground
Oscillator output
H or L or Open: No effect on output frequency or other device
functions
Power supply
voltage
[10]
VIN
NC/OE/ST
GND
1
6
Top View
VDD
NC
CLK
2
5
3
4
Figure 2.
Notes:
8. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 2 in the 6-pin package is not externally driven. If pin 2 needs to be left floating, use
the NC option
9. Typical value of the weak pull-down impedance is 5 mΩ
10. A capacitor value of 0.1 µF between VDD and GND is recommended.
Table 4. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance of
the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Min.
-65
-0.5
–
–
Max.
150
4
2000
260
Unit
°C
V
V
°C
Table 5. Thermal Consideration
Parameter
7050
5032
3225
2520
JA, 4 Layer Board
(°C/W)
191
97
109
117
JA, 2 Layer Board
(°C/W)
263
199
212
222
JC, Bottom
(°C/W)
30
24
27
26
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Rev. 1.01
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Page 3 of 11
www.sitime.com
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Phase Noise Plot
-100
-110
-120
-130
-140
-150
-160
-170
3
10
Integrated random phase jitter (RMS, 12kHz-5MHz): 0.52ps
The Chinese character fonts are as follows: 0x01,0xF0,0x21,0x10,0x11,0x10,0x11,0x10,//0"Set", 0x01,0x10,0x02,0x0E,0xF4,0x00,0x13,0xF8, 0x11,0x08,0x11,0x10,0x10,0x90,0x10,0xA0, 0x14,0x40,0x18,0xB0,0x13...
[font=宋体][size=4] I worked overtime a little late at night, and I was still worried about this code when I came back, so I still looked for the reason. It should have been solved. [/size][/font][font=...
My face is confused!!! My head is all messed up because of my illness. My family may have to thank me for being sick, because I don’t have the energy to shop. I just suddenly found out that today is D...
Q: How to develop irregular windows in EVC (wince)? Please advise if you have succeeded. My current problem is that I can develop irregular windows by using area methods such as SetWindowRgn. But the ...
I want to start from the basics and take classes in Shanghai on weekends. The teachers are capable and have some development experience. I want to learn hardware design and the ultimate goal is to be ...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
In recent years, with the increasing demand for manufacturing and automated production management, industrial barcode scanners have gradually become an indispensable part of the industrial manufact...[Details]
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
The jammer is a signal blocker, mainly composed of a chip and a radio transmitter. When the car owner presses the remote control lock button, the jammer interferes with the electronic lock receivin...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
Recently, South Korean robotics giant WIRobotics launched its first general-purpose humanoid robot, ALLEX, at the Robotics Innovation Center (RIH) at the Korea University of Science and Technology....[Details]
In the summer of 2025, BlueOval SK, a joint venture between Ford and SK On, officially started production at its first battery factory in Kentucky.
According to the original plan, this w...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
Programming Basics
京公网安备 11010802033920号
EEWORLD
