RNCP1206FTD10K7 datasheet, PDF

Datasheet> All Categories > Passive components> RNCP1206FTD10K7

RNCP1206FTD10K7: DescriptionRES 10.7K OHM 1% 1/2W 1206; CategoryPassive components; File Size327KB，6 Pages; ManufacturerStackpole Electronics Inc; Environmental Compliance

Download Datasheet Parametric View All

RNCP1206FTD10K7 Overview

RES 10.7K OHM 1% 1/2W 1206

RNCP1206FTD10K7 Parametric

Parameter Name	Attribute value
resistance	10.7 kOhms
Tolerance	±1%
Power (W)	0.5W，1/2W
component	thin film
characteristic	Resistant to vulcanization and moisture
Temperature Coefficient	±100ppm/°C
Operating temperature	-55°C ~ 155°C
Package/casing	1206 (3216 metric)
Supplier device packaging	1206
size/dimensions	0.122" long x 0.059" wide (3.10mm x 1.50mm)
Height - Installation (maximum)	0.024"（0.60mm）
Number of terminals	2
failure rate	-

Preview

Download Datasheet

View All

RNCP Series

High Power Anti-Sulfur Thin Film Chip Resistor

Features:

•

Stackpole Electronics, Inc.

Resistive Product Solutions

Higher power ratings than standard thick film chips

Absolute TCRs to ±100 ppm/°C

Inner termination engineered to deter sulfur contamination

Absolute Tolerances to 1%

Completely lead free - RoHS compliant and halogen free

Comparable in cost to standard thick film chip resistors

Electrical Specifications

Type / Code

RNCP0402

RNCP0603

RNCP0805

Power Rating

(Watts) @ 70ºC

0.1W

0.125W

0.25W

(1)

Maximum Working

(2)

Voltage

50V

150V

Maximum Overload

Voltage

100V

300V

Resistance

Temperature

Coefficient

Ohmic Range (Ω) and

Tolerance

1%, 5%

1 - 10K

1 - 47K

1 - 100K

±100 ppm/ºC

200V

400V

RNCP1206

0.5W

(1) Power rating for each package size is valid if ambient temp ≤80°C and terminal temp ≤105°C

(2) Lesser of √PR or maximum working voltage

Certain resistance values will require a high minimum order quantity. Contact Stackpole Customer Service for details.

Please refer to the High Power Resistor Application Note (page 5) for more information on designing and implementing

high power resistor types.

Mechanical Specifications

Type / Code

RNCP0402

RNCP0603

RNCP0805

RNCP1206

Body Length

0.039 ± 0.004

1.00 ± 0.10

0.059 ± 0.004

1.50 ± 0.10

0.079 ± 0.006

2.00 ± 0.15

0.122 ± 0.008

3.10 ± 0.20

Body Width

0.020 ± 0.002

0.50 ± 0.05

0.031 ± 0.004

0.80 ± 0.10

0.049 ± 0.006

1.25 ± 0.15

0.059 ± 0.008

1.50 ± 0.20

Body Height

0.012 ± 0.002

0.30 ± 0.05

0.016 ± 0.004

0.40 ± 0.10

0.020 ± 0.004

0.50 ± 0.10

0.020 ± 0.004

0.50 ± 0.10

Top Termination

0.010 ± 0.006

0.25 ± 0.15

0.012 ± 0.008

0.30 ± 0.20

0.016 ± 0.008

0.40 ± 0.20

0.020 ± 0.012

0.50 ± 0.30

Bottom Termination

0.012 ± 0.006

0.30 ± 0.15

0.016 ± 0.008

0.40 ± 0.20

0.024 ± 0.008

0.60 ± 0.20

0.028 ± 0.008

0.70 ± 0.20

Unit

inches

Rev Date: 10/23/2017

This specification may be changed at any time without prior notice

Please confirm technical specifications before you order and/or use.

www.seielect.com

marketing@seielect.com

RNCP Series

High Power Anti-Sulfur Thin Film Chip Resistor

Stackpole Electronics, Inc.

Resistive Product Solutions

High Power Chip Resistors and Thermal Management

Stackpole has developed several surface mount resistor series in addition to our current sense resistors,

which have had higher power ratings than standard resistor chips. This has caused some uncertainty and

even confusion by users as to how to reliably use these resistors at the higher power ratings in their designs.

The data sheets for the RHC, RMCP, RNCP, CSR, CSRN, CSRF, CSS, and CSSH state that the rated

power assumes an ambient temperature of no more than 100°C for the CSS / CSSH series and 70°C for all

other high power resistor series. In addition, IPC and UL best practices dictate that the combined

temperature on any resistor due to power dissipated and ambient air shall be no more than 105°C. At first

glance this wouldn’t seem too difficult, however the graph below shows typical heat rise for the CSR ½ 100

milliohm at full rated power. The heat rise for the RMCP and RNCP would be similar. The RHC with its

unique materials, design, and processes would have less heat rise and therefore would be easier to

implement for any given customer.

The 102°C heat rise shown here would indicate there will be additional thermal reduction techniques needed

to keep this part under 105°C total hot spot temperature if this part is to be used at 0.75 watts of power.

However, this same part at the usual power rating for this size would have a heat rise of around 72°C. This

additional heat rise may be dealt with using wider conductor traces, larger solder pads and land patterns

under the solder mask, heavier copper in the conductors, via through PCB, air movement, and heat sinks,

among many other techniques. Because of the variety of methods customers can use to lower the effective

heat rise of the circuit, resistor manufacturers simply specify power ratings with the limitations on ambient air

temperature and total hot spot temperatures and leave the details of how to best accomplish this to the

design engineers. Design guidelines for products in various market segments can vary widely so it would be

unnecessarily constraining for a resistor manufacturer to recommend the use of any of these methods over

another.

Note:

The final resistance value can be affected by the board layout and assembly process, especially the size of the

mounting pads and the amount of solder used. This is especially notable for resistance values ≤ 50mΩ.

This should be taken into account when designing.

Rev Date: 10/23/2017

This specification may be changed at any time without prior notice

Please confirm technical specifications before you order and/or use.

www.seielect.com

marketing@seielect.com

Recommended Resources

Printing factory monochrome offset printing machine circuit

Thyristor AC switch circuit 2b

Several protection circuit power consumption curves and waveform diagrams

Overvoltage and overcurrent protection circuit diagram using NE555

One of the circuit diagrams for changing the output voltage of the secondary double-winding transformer

Two-line intercom telephone circuit diagram

Please explain the red part (C language programming: [align=left][color=#000000][font=Times New Roman]// [/font]Use [font=Times New Roman]TMR0[/font] to measure key pulse width. [font=Times New Roman] [/font]The crystal uses [font=Times New Roman]4M[/fo...; 183283726 Microchip MCU

I used to make a batch of digital tubes that were left over from making audio equipment. There are about 1,000 of them. If you want them, I'm selling them at a low price.: [size=6]I have a batch of custom digital tubes left over from making audio equipment before. There are about 1,000 of them. If you can use them, please contact me at QQ 226748105. Please indicate the ...; 青龙偃月 Buy&Sell

Urgent!!! Looking for GAL's 8-way design (waiting online): It is best to use ABEL to write the GAL frequency division program...; forhelp Embedded System

Creative Modification Competition: The moderator gave me two booster boards, and I used both of them.: Creative Modification Competition: The moderator gave me two booster boards. I used both boards and modified them into a multimeter and a clamp multimeter power supply!1. The boost board is installed ...; lanhua Power technology

Serialport reading serial port problem: Why can I read serial port data normally using serialport in Windows program, but not in emulator? Please help me solve it, thank you!...; sandy0701 Embedded System

A brief talk about RISC-V GCC: Linker script learning notes (Part 2): The previous article introduced some link script knowledge. This time we use the CH57x series template project built into MRS (MounRiver Studio) to practice it: 1EntranceENTRY keyword, to make sure th...; Moiiiiilter MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components