EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
LT3694-1 PINOUT IS SHOWN IN PARENTHESIS
FE PACKAGE
20-LEAD PLASTIC TSSOP
θ
JA
= 38°C/W
EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB
LT3694-1 PINOUT IS SHOWN IN PARENTHESIS
ORDER INFORMATION
LEAD FREE FINISH
LT3694EUFD#PBF
LT3694IUFD#PBF
LT3694EFE#PBF
LT3694IFE#PBF
LT3694-1EUFD#PBF
LT3694-1IUFD#PBF
LT3694-1EFE#PBF
LT3694-1IFE#PBF
TAPE AND REEL
LT3694EUFD#TRPBF
LT3694IUFD#TRPBF
LT3694EFE#TRPBF
LT3694IFE#TRPBF
LT3694-1EUFD#TRPBF
LT3694-1IUFD#TRPBF
LT3694-1EFE#TRPBF
LT3694-1IFE#TRPBF
PART MARKING*
3694
3694
LT3694FE
LT3694FE
36941
36941
LT3694FE-1
LT3694FE-1
PACKAGE DESCRIPTION
28-Lead (4mm
×
5mm) Plastic QFN
28-Lead (4mm
×
5mm) Plastic QFN
20-Lead Plastic TSSOP
20-Lead Plastic TSSOP
28-Lead (4mm
×
5mm) Plastic QFN
28-Lead (4mm
×
5mm) Plastic QFN
20-Lead Plastic TSSOP
20-Lead Plastic TSSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
36941fb
2
LT3694/LT3694-1
ELECTRICAL CHARACTERISTICS
PARAMETER
V
IN
Internal Undervoltage Lockout
Overvoltage Shutdown Threshold
Input Quiescent Current
Bias Quiescent Current
Shutdown Current
EN/UVLO Threshold, Bias On
EN/UVLO Threshold, Switching On
Reference Voltage Line Regulation
Switching Frequency
SYNC Input Frequency Range
V
IH
, SYNC
V
IL
, SYNC
V
OH
, CLKOUT
V
OL
, CLKOUT
PGOOD Output Voltage Low
PGOOD Leakage
PGOOD Threshold (Relative to V
FB
)
Switching Regulator
Feedback Pin Voltage
Feedback Pin Bias Current
Error Amplifier Transconductance
Error Amplifier Voltage Gain
TRK/SS Pull-Up Current
TRK/SS Threshold to Start Switching
V
C1
Source Current
V
C1
Sink Current
V
C1
Clamp Voltage
V
C1
Switching Threshold
V
C1
to Switch Current Gain
Switch Leakage Current
Minimum Boost Voltage Above Switch
Switch Current Limit (Note 3)
Switch V
CESAT
BST Operating Current
V
F
, BST Diode
I
L
BST Diode
DA Current Limit
Minimum Switch Off-Time
V
IN
= 36V
(Note 4)
(Note 3) 10% Duty Cycle
I
SW1
= 3A
I
SW1
= 3A
I
BST
= 100mA
V
BST
– V
BIAS
= 36V
l
l
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= 12V, V
BIAS
= 3V, unless otherwise noted. (Notes 2, 9)
CONDITIONS
l
l
MIN
3.5
36
TYP
3.8
38
1
2
0.1
MAX
4
40
2
3.5
2
1.23
1.1
2.5
0.35
UNITS
V
V
mA
mA
µA
mV
V
%/V
MHz
MHz
V
V
V
V
V
nA
%
mV
nA
µS
V/V
Not Switching
Not Switching
V
EN/UVLO
= 0.1V
350
1.16
0.9
0.25
1.5
1.6
5V < V
IN
< 36V
R
T
= 40.2k
LT3694 Only
LT3694 Only
LT3694 Only
I
CLKOUT
= –50µA, LT3694-1 Only
I
CLKOUT
= 50µA, LT3694-1 Only
I
PGOOD
= 250µA
V
PGOOD
= 2V
(Note 8)
86
735
l
l
l
l
l
l
500
1.2
0.01
1.0
2.6
0.3
0.2
10
90
750
–50
350
600
0.4
1000
94
765
–500
–2
35
V
C
= 0.6V
V
C
= 0.6V
–3
50
–20
28
2
0.75
3.6
0.01
1.8
–4
70
µA
mV
µA
µA
V
V
A/V
10
2.5
6
µA
V
A
mV
mA
V
µA
3.5
4.9
600
60
0.8
1
2.6
3.6
4.5
140
A
ns
36941fb
3
LT3694/LT3694-1
ELECTRICAL CHARACTERISTICS
PARAMETER
LDO Regulator
Feedback Pin Voltage
Feedback Pin Bias Current
Error Amplifier Voltage Gain
TRK/SS Pull-Up Current
TRK/SS Threshold to Shut Down LDO
Line Regulation
Load Regulation
Base Drive
Current Limit Threshold
Short-Circuit Current Limit Threshold
Minimum BIAS to DRV Voltage (Note 7)
Minimum V
IN
to DRV Voltage
V
FB
= 0
I
DRV
= 10mA
I
DRV
= 10mA
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= 12V, V
BIAS
= 3V, unless otherwise noted. (Notes 2, 9)
CONDITIONS
MIN
735
TYP
750
–50
2800
–2
35
5V < V
IN
< 36V
I
DRV
From 0.1mA to 10mA
l
l
MAX
765
–500
–4
70
UNITS
mV
nA
µA
mV
%/V
mV/mA
–3
50
0.025
0.5
10
47
22
15
60
26
0.3
2.0
20
70
30
0.9
2.3
mA
mV
mV
V
V
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT3694E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3694I is guaranteed to meet performance specifications from –40°C to
125°C junction temperature.
Note 3:
Current limit is guaranteed by design and/or correlation to static
test. Slope compensation reduces current limit at higher duty cycles.
Note 4:
This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions.
Junction temperature will exceed the maximum operating range when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair
device reliability.
Note 6:
Absolute Maximum Voltage at V
IN
and EN/UVLO pins is 70V for
non-repetitive, 1 second transients and 36V for continuous operation.
Note 7:
The LDO will function if the BIAS to DRV differential is not met,
but the base drive current will be drawn from V
IN
instead of BIAS.
Note 8:
The PGOOD pin will pull low when the voltage on any of the three
FB pins is lower than the PGOOD threshold value.
Note 9:
Positive currents flow into pins, negative currents flow out of pins.
Minimum and maximum values refer to absolute values.
I have a question. When using JATG to debug the program online, if the target board has a high-speed data stream to receive, such as a serial port with a baud rate of 115200, if the refresh function i...
Event details: https://bbs.eeworld.com.cn/elecplay/content/182
Updated: October 22Evaluation report summary:
@x1816
R329 Zhouyi AIPU environment construction and simulation practice
MaixSense R329 Dev...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:47[/i] [align=center][table=98%][tr][td][align=center][align=center][b][font=楷体_GB2312][size=18pt]Notice on the 2008 Electronic Design Compet...
Recruiting 4 engineers and assistant engineers. No restrictions on education, age or gender. Job description: Write programs on PC to control tester to test integrated circuits and handle test excepti...
The inspiration of this creative seaweed lamp comes from scientists' research on seaweed. They found that when seaweed performs photosynthesis, a small current is generated. So this seaweed lamp appli...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, this proportion may be as high as 30-40% as more safety electronics, fuel consumption and ...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
With the continuous advancement of various technologies in the field of measurement and control, the baseband subsystem of general measurement and control equipment has entered the fourth generation o...[Details]
With the rapid development of the national economy, lifting and hoisting operations are used more and more frequently and widely in various fields of economic construction. China has continuously expl...[Details]
Abstract: Based on the ZigBee parking lot SMS car search system, the location of the vehicle in the parking lot is sent to the owner through SMS, which is convenient for the owner to quickly find ...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
IntroductionLED
billboards are a kind of information display terminal for the public, which has a wide range of civil and commercial values. However, the information displayed on most LED bil...[Details]
introduction
Sudan's Muglad Oilfield is a large oilfield jointly invested, developed and constructed by a four-party consortium of China, Malaysia, Canada and Sudan. It consists of 8 satellite...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
