CRCW01005 e3
www.vishay.com
Vishay
Standard Thick Film Chip Resistors
FEATURES
• Very small standard size (0.4 mm x 0.2 mm)
• Low tolerance (1 %)
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
CASE
SIZE
IMPERIAL
CASE
SIZE
METRIC
POWER RATING
P
70
W
LIMITING
ELEMENT
VOLTAGE
U
max.
AC
RMS
/DC
V
TEMPERATURE
RESISTANCE
TOLERANCE
COEFFICIENT
RANGE
%
ppm/K
TYPE
SERIES
±1
± 250
± 2, ± 5
0.031
CRCW01005
01005
RR0402M
-200/+600
± 2, ± 5
Zero-Ohm-Resistor:
R
max.
= 50 m,
I
max.
= 0.5 A
1.0 to 9.1
15
±1
1.0 to 9.76
10.0 to 1M
E24; E96
E24
E24; E96
E24
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
PARAMETER
Rated Dissipation
P
70 (1)
Operating Voltage
U
max.
AC
RMS
/DC
Insulation Voltage
U
ins
(1 min)
Insulation Resistance
Operating Temperature Range
Mass
UNIT
W
V
V
°C
mg
CRCW01005
0.031
15
30
> 10
9
-55 to +125
0.07
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 125 °C is not exceeded.
Revision: 06-Nov-13
Document Number: 20056
1
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW01005 e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW01001K00FREL
C
R
C
W
0
1
0
0
1
K
0
0
F
R
E
L
TYPE
CRCW0100
VALUE
R
= Decimal
K
= Thousand
M
= Million
0000
= Jumper
TOLERANCE
F
= ± 1.0 %
G
= ± 2.0 %
J
= ± 5.0 %
Z
= Jumper
TCR
R
= ± 250 ppm/K
Y
= -200 ppm/K/+600 ppm/K
0
= Jumper
PACKAGING
EL
PRODUCT DESCRIPTION: CRCW01005 250 1K0 1 % ET3 e3
CRCW01005
TYPE
CRCW01005
250
TCR
± 250
ppm/K
-200/+600
ppm/K
1K0
RESISTANCE
VALUE
1R0
= 1
10R
= 10
1K0
= 1 k
10K
= 10 k
1M0
= 1 M
0R0
= Jumper
1%
TOLERANCE
VALUE
±1%
±2%
±5%
ET3
PACKAGING
ET3
e3
LEAD (Pb)-FREE
e3
= Pure tin
termination finish
PACKAGING
TYPE
CRCW01005
CODE
EL = ET3
QUANTITY
20 000
CARRIER TAPE
Paper tape acc. to IEC 60286-3, Type 1a
WIDTH
8 mm
PITCH
2 mm
REEL DIAMETER
180 mm/7"
DIMENSIONS
in millimeters
SIZE
IMPERIAL
01005
METRIC
RR0402M
L
0.4 ± 0.02
W
0.2 ± 0.02
DIMENSIONS
H
0.13 ± 0.02
T1
0.10 ± 0.03
T2
0.10 ± 0.03
RECOMMENDED SOLDER PAD
DIMENSIONS
a
0.15
b
0.2
l
0.2
Note
• No marking for 01005 size.
DERATING
Fraction of Rated Dissipation
P
70
in %
100
50
0
- 50
0
50
100
125
150
70
Ambient Temperature
ϑ
amb
in °C
Revision: 06-Nov-13
Document Number: 20056
2
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CRCW01005 e3
www.vishay.com
Vishay
REQUIREMENTS
PERMISSIBLE CHANGE (R)
STABILITY CLASS 1 OR BETTER
Stability for product types:
CRCW01005 e3
1
to 1 M
± 1 %; ± 2 %; ± 5 %
± (2 %
R
+ 0.1
)
Resistance
-
U
= 2.5 x
P
70
x
R
2 x
U
max.
;
duration according to style
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(235 ± 3) °C
(2 ± 0.5) s
(20/-55/20) °C and
(20/125/20) °C
Depth 3 mm; 1 time
15 min. at -55 °C;
15 min. at 125 °C;
300 cycles
U
=
P
70
x
R
U
max.
;
1.5 h on; 0.5 h off;
70 °C; 1000 h
Solder bath method
(260 ± 5) °C; (10 ± 1) s
(40 ± 2) °C; (90 to 95) % RH;
1000 h
125 °C, 1000 h
Isopropyl alcohol;
(20 to 25) °C; (5 ± 0.5) min
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
-
-
PROCEDURE
TEST
4.5
4.13
Short time overload
Good tinning ( 95 % covered)
no visible damage
4.17.2
58 (Td)
Solderability
Good tinning ( 95 % covered)
no visible damage
- 200 ppm/K/+600 ppm/K,
± 250 ppm/K
No visible damage,
no open circuit in bent position
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
4.8.4.2
4.33
-
21 (Uu
1
)
Temperature coefficient
Substrate bending
Rapid change
of temperature
4.19
14 (Na)
4.25.1
-
Endurance at 70 °C
Resistance to
soldering heat
Damp heat, steady state
Endurance at upper
category temperature
Component
solvent resistance
± (5 %
R
+ 0.1
)
± (2 %
R
+ 0.1
)
± (5 %
R
+ 0.1
)
± (2 %
R
+ 0.1
)
No visible damage
4.18.2
4.24
4.25.3
4.29
58 (Td)
78 (Cab)
-
45 (XA)
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 06-Nov-13
Document Number: 20056
3
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
1
Document Number: 91000
京公网安备 11010802033920号
EEWORLD
