Specifications are subject to change without notice.
Revised: 09/15/17
Thyristors
Surface Mount – 50 - 800V > 2N6400
Maximum Ratings †
(T
J
= 25°C unless otherwise noted)
Rating
Part Number
Symbol
Value
Unit
2N6400
2N6401
Peak Repetitive Off-State Voltage (Note 1)
(T
J
= -40 to 110°C, Sine Wave, 50 to 60 Hz, Gate Open)
2N6402
2N6403
2N6404
2N6405
On-State RMS Current
(180° Conduction Angles; T
C
= 100°C)
Average On-State RMS Current
(180° Conduction Angles; T
C
= 100°C)
Peak Non−Repetitive Surge Current
(1/2 Cycle, Sine Wave, 60 Hz, T
J
= 90°C)
Circuit Fusing Considerations (t = 8.3 ms)
Forward Peak Gate Power (Pulse Width ≤ 1.0 µs, T
C
= 100°C)
Forward Average Gate Power (t = 8.3 ms, T
C
= 100°C)
Forward Peak Gate Current (Pulse Width ≤ 1.0 µs, T
C
= 100°C)
Operating Junction Temperature Range
Storage Temperature Range
†Indicates JEDEC Registered Data
50
100
V
DRM,
V
RRM
200
400
600
800
I
T
16
A
V
(RMS)
I
T
(AV)
10
A
I
TSM
I
2
t
P
GM
P
G(AV)
I
GM
T
J
T
stg
160
145
20
0.5
2.0
-40 to +125
-40 to +125
A
A
2
s
W
W
A
°C
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is
not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
1. V
DRM
and V
RRM
for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent
with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
Maximum Ratings †
(T
J
= 25°C unless otherwise noted)
Rating
Thermal Resistance, Junction-to-Case
Maximum Lead Temperature for Soldering Purposes, 1/8” from
[i=s]This post was last edited by gh131413 on 2014-10-18 10:26[/i] Maybe I have been out for too long, the bright lights and nightlife of this city are no longer new to me, I mechanically repeat going...
Abstract Aiming at the shortcomings of the classical multi-dimensional calibration MDS-MAP algorithm in positioning accuracy and matrix calculation complexity, a distributed positioning algorithm base...
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
Direct digital frequency synthesis (DDS) has fast frequency switching and modulation capabilities and is widely used. However, when low power consumption and low cost are the main considerations, D...[Details]
Based on the actual situation, a remote intelligent anti-theft alarm device for home use, connected to the telephone line, simple to operate, and stable and reliable in operation is designed. When ...[Details]
Infrared remote control is widely used in home appliances, but the remote controls produced are not compatible with each other. The universal remote controls commonly seen on the market can only co...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
