RNCF2010BTE158K datasheet, PDF

Datasheet> All Categories > Passive components> RNCF2010BTE158K

RNCF2010BTE158K: DescriptionRES 158K OHM 0.1% 1/3W 2010; CategoryPassive components; File Size316KB，8 Pages; ManufacturerStackpole Electronics Inc; Environmental Compliance

Download Datasheet Parametric View All

RNCF2010BTE158K Overview

RES 158K OHM 0.1% 1/3W 2010

RNCF2010BTE158K Parametric

Parameter Name	Attribute value
resistance	158 kOhms
Tolerance	±0.1%
Power (W)	0.333W，1/3W
component	thin film
characteristic	Automotive grade AEC-Q200
Temperature Coefficient	±25ppm/°C
Operating temperature	-55°C ~ 155°C
Package/casing	2010 (5025 Metric)
Supplier device packaging	2010
size/dimensions	0.193" long x 0.094" wide (4.90mm x 2.40mm)
Height - Installation (maximum)	0.026"（0.65mm）
Number of terminals	2
failure rate	-

Preview

Download Datasheet

View All

RNCF Series

Precision Thin Film Chip Resistor

Features:

•

Stackpole Electronics, Inc.

Resistive Product Solutions

Precision tolerances to ±0.01%

TCR down to ±2ppm/ºC

Wide R-value range

Lower values may be available

Consult factory for tighter tolerances

Qualified to AEC-Q200

RoHS compliant and halogen free

Electrical Specifications

Power Rating Maximum

Working

Type / Code (Watts) @

70ºC

Voltage

(1)

RNCF0201

0.032W

15V

Maximum Resistance

Overload Temperature

Voltage

Coefficient

30V

±25 ppm/ºC

±50 ppm/ºC

±2 ppm/ºC

±5 ppm/ºC

RNCF0402

0.063W

25V

50V

±10 ppm/ºC

±15 ppm/ºC

±25 ppm/ºC

±50 ppm/ºC

±5 ppm/ºC

±10 ppm/ºC

0.063W

50V

100V

±15 ppm/ºC

±25 ppm/ºC

±50 ppm/ºC

±2 ppm/ºC

RNCF0603

0.1W

75V

150V

±5 ppm/ºC

±10 ppm/ºC

±15 ppm/ºC

±25 ppm/ºC

±50 ppm/ºC

±25 ppm/ºC

±50 ppm/ºC

±5 ppm/ºC

±10 ppm/ºC

0.1W

100V

200V

±15 ppm/ºC

±25 ppm/ºC

±50 ppm/ºC

±2 ppm/ºC

±5 ppm/ºC

RNCF0805

0.125W

150V

300V

±10 ppm/ºC

±15 ppm/ºC

±25 ppm/ºC

±50 ppm/ºC

0.25W

150V

300V

±25 ppm/ºC

±50 ppm/ºC

24.9 - 200K

4.7 - 511K

4.7 - 9.88

4.7 - 9.88 and

505K - 1M

4.7 - 9.88 and

505K - 1M

10 - 499K

517K - 1M

24.9 - 30K

4.7 - 511K

4.7 - 1M

1 - 9.88 and 505K - 1M

24.9 - 100K

4.7 - 9.88

24.9 - 15K

4.7 - 332K

4.7 - 9.88 and 336K - 1M

10 - 332K

30.5K - 150K

517K - 1M

1.01M - 2M

49.9 - 20K

49.9 - 12K

10 - 511K

15.2K - 60K

336K - 511K

1 - 4.64

49.9 - 4.99K

49.9 - 20K

49.9 - 100K

49.9 - 69.8K

4.7 - 511K

Ohmic Range (Ω) and Tolerance

0.01%

0.05%

0.1%

0.25%

0.5%

49.9 - 33K

49.9 - 4.99K

0.166W

100V

150V

(1) Lesser of √P*R or maximum working voltage.

Rev Date: 07/13/2018

This specification may be changed at any time without prior notice

Please confirm technical specifications before you order and/or use.

www.seielect.com

marketing@seielect.com

Recommended Resources

Digital display temperature detection circuit

Energy-saving three-phase asynchronous motor phase failure protection circuit

465kHz IF signal generator circuit

Passive tone control circuit.gif

Midea NY-18K, NY-21K oil-filled electric heater circuit diagram

Cleverly modify the doorbell into a dual-purpose doorbell and alarm circuit

The problem of PCB parasitic capacitance: [i=s] This post was last edited by S3S4S5S6 on 2017-11-9 08:48 [/i] An oscillation circuit was built using TLV3501 according to the typical application in the manual. After PCB layout, it was found th...; S3S4S5S6 PCB Design

Why can the reference layer of PCB also be the power layer?: As shown in the figure above, in a 4-layer PCB stack, why can the differential line refer to the third layer (Power layer)? I understand that ordinary single-ended signals must be referenced to the gr...; xiaominwzj PCB Design

I drew the schematic using protues software, and after converting it into a PCB diagram, I found that only the buzzer was not packaged.: I finished drawing the schematic diagram using protues software. After converting it into PCB diagram, I found that only the buzzer was not packaged. After checking online, I found that I had to draw ...; 圈在指尖 PCB Design

Questions about SPI in 5438: The direction of the signal on the middle line is from slave to master. Does it mean that the slave controls the UCxSTE bit of the master? But I think it should be manually decided in the program whet...; zzbaizhi Microcontroller MCU

Basic knowledge of automobile body design: This article provides some basic knowledge of automobile body design, which is suitable for learning and training of relevant departments in the automobile industry. Main contents: Main components of ...; frozenviolet Automotive Electronics

Please help me read the next program, which is to clear the RAM from 0200H to 05FFH! Is it correct?: Please help me look at the next program, which is to clear the RAM from 0200H to 05FFH!Is this correct? Because it feels like it should be written. Shouldn't Address be +2 each time?unsigned int *ptr;...; 零晨 Microcontroller MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components