Storage Temperature Range..............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
Soldering Temperature (reflow) ......................................+260°C
ESD Results―Human Body Model (MAX16910E)............. 2.5kV
*As per JEDEC51 Standard (multilayer board).
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional opera-
tion of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Package Thermal Characteristics
(Note 1)
TDFN
Junction-to-Ambient Thermal Resistance (q
JA
) ..........41°C/W
Junction-to-Case Thermal Resistance (q
JC
) .................8°C/W
SO
Junction-to-Ambient Thermal Resistance (q
JA
) ..........53°C/W
Junction-to-Case Thermal Resistance (q
JC
) .................7°C/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
Electrical Characteristics
(V
IN
= V
ENABLE
= +14V, C
TIMEOUT
= open, C
IN
= 1µF, C
OUT
= 4.7µF, unless otherwise noted. T
A
= -40°C to +125°C, T
A
P
T
J
P
+150°C, unless otherwise noted. Typical values are T
A
= +25°C.) (Note 2)
PARAMETER
Supply Voltage Range
Supply Current
Shutdown Supply Current
I
SHDN
SYMBOL
V
IN
Continuous
For
P
400ms
I
LOAD
= 0mA, SET = GND, V
OUT
= 5V
ENABLE = GND, T
A
= +25NC
ENABLE = GND, -40NC
P
T
A
P
+125NC
1mA
P
I
LOAD
P
200mA,
V
IN
= 6V to 30V (Note 3)
1mA
P
I
LOAD
P
50mA,
V
IN
= 6V to 30V, T
J
= +150°C (Notes 3, 4)
1mA
P
I
LOAD
P
200mA, V
IN
= 4.8V to 30V
(Note 3)
1mA
P
I
LOAD
P
50mA, V
IN
= 4.8V to 30V,
T
J
= +150°C (Notes 3, 4)
I
LOAD
= 1mA (Note 4)
I
LOAD
= 200mA, SET = GND, SETOV =
HIGH, V
OUT(NORM)
= +5.0V
Dropout Voltage (Note 5)
DV
DO
I
LOAD
= 50mA, SET = GND, SETOV =
HIGH, V
OUT(NORM)
= +5.0V, T
J
= +150°C
(Notes 3, 4)
4.9
4.9
3.234
3.234
1.5
1.225
1.25
280
20
1.6
3
5.0
5.0
3.3
3.3
5.1
V
5.1
3.366
V
3.366
11.0
1.275
600
mV
600
V
V
CONDITIONS
MIN
3.5
TYP
MAX
30
45
30
3
UNITS
V
FA
FA
Output Voltage
(5V Fixed Output Setting)
V
OUT50
Output Voltage
(3.3V Fixed Output Setting)
Adjustable Output-Voltage Range
SETOV FB Voltage
V
OUT33
V
OUT
V
SETOV
www.maximintegrated.com
Maxim Integrated
│
3
MAX16910
200mA, Automotive, Ultra-Low
Quiescent Current, Linear Regulator
Electrical Characteristics (continued)
(V
IN
= V
ENABLE
= +14V, C
TIMEOUT
= open, C
IN
= 1µF, C
OUT
= 4.7µF, unless otherwise noted. T
A
= -40°C to +125°C, T
A
P
T
J
P
+150°C, unless otherwise noted. Typical values are T
A
= +25°C.) (Note 2)
PARAMETER
Short-Circuit Output Current Limit
Thermal Shutdown
Thermal Shutdown Hysteresis
Line Regulation
(5V Fixed Output Setting)
Line Regulation
(3.3V Fixed Output Setting)
Load Regulation
(5V Fixed Output Setting)
Load Regulation
(3.3V Fixed Output Setting)
Power-Supply Rejection Ratio
Startup Response Time
TIMEOUT INPUT
TIMEOUT Ramp Current
TIMEOUT Ramp Delay
RESET
Default Timeout Period
RESET OUTPUT
RESET
Threshold
RESET
Threshold Hysteresis
OUT to
RESET
Delay
RESET
Output-Voltage Low
(Open-Drain)
RESET
Open-Drain Leakage
Current
RESET
Open-Drain Leakage
Current
ENABLE
ENABLE Logic-Low
ENABLE Logic-High
ENABLE Pulldown Current
SET INPUT
SET Input Current (All Modes)
SET Logic-Low
Set Logic-High
V
ILSET
V
IHSET
2.4
T
A
= +25NC
T
J
= +150NC
-50
0.2
0.4
+50
nA
FA
V
V
V
IL
V
IH
(Note 7)
2.4
0.65
0.4
V
V
FA
V
OL
MAX16910__9/V+, V
OUT
falling
MAX16910__8/V+, V
OUT
falling
V
OUT
rising
V
OUT
falling (Note 6)
I
SINK
= 0.5mA,
RESET
asserted
RESET
not asserted,
RESET
= 7V,
T
A
= +25NC
RESET
not asserted,
RESET
= 7V
0.03
90
85
92.5
87.5
5
4
0.4
1
94
89
% of
V
OUT
% of
V
OUT
Fs
V
FA
FA
V
OUT
rising, TIMEOUT = OPEN
30
I
TO
TIMEOUT connected to GND
0.600
1.0
1.25
60
90
1.650
FA
ms/nF
Fs
PSRR
t
START
SYMBOL
I
SC
(Note 6)
(Note 6)
V
IN
= 6V to 30V, I
LOAD
= 1mA
V
IN
= 4.8V to 30V, I
LOAD
= 1mA
I
LOAD
= 1mA to 200mA
I
LOAD
= 1mA to 200mA
I
LOAD
= 10mA, f = 100Hz, 500mV
P-P
(Note 6)
Rising edge of V
IN
to V
OUT
, I
LOAD
= 50mA
(Note 6)
CONDITIONS
Output shorted to GND (MAX16910C__)
MIN
230
TYP
330
+180
+25
1
1
12
12
60
160
MAX
UNITS
mA
NC
NC
mV
mV
mV
mV
dB
Fs
www.maximintegrated.com
Maxim Integrated
│
4
MAX16910
200mA, Automotive, Ultra-Low
Quiescent Current, Linear Regulator
Electrical Characteristics (continued)
(V
IN
= V
ENABLE
= +14V, C
TIMEOUT
= open, C
IN
= 1µF, C
OUT
= 4.7µF, unless otherwise noted. T
A
= -40°C to +125°C, T
A
P
T
J
P
+150°C, unless otherwise noted. Typical values are T
A
= +25°C.) (Note 2)
PARAMETER
SETOV INPUT (TRI-MODE)
SETOV Input Leakage Current
SETOV Low-Level Input Voltage
SETOV High-Level Input Voltage
V
ILSETOV
V
IHSETOV
SYMBOL
CONDITIONS
SET = HIGH, V
SETOV
= 5V
or SET = GND, V
SETOV
= 5V
SET = GND, V
SETOV
< V
ILSETOV
or places
device in +3.3V fixed output-voltage mode
SET = GND, V
SETOV
> V
IHSETOV
or places
device in +5V fixed output-voltage mode
V
OUT
- 0.4
MIN
TYP
1
0.4
MAX
UNITS
FA
V
V
Note 2:
Production tested at T
A
= +25°C. Overtemperature limits are guaranteed by ATE characterization between -40°C
P
T
J
≤
+150°C, unless otherwise noted.
Note 3:
Observe the absolute maximum power dissipation limits.
Note 4:
Specification characterized up to +150°C operating junction temperature. Limits are guaranteed by bench characterization.
I am not sharing this article to denigrate .NET, and I have never used .NET. However, the problems mentioned in this article are very similar to those you encounter when designing electronic devices.A...
Currently we are using wince6.0 + Samsung 6410. Problem 1: Sometimes the USB connection cannot be made, but sometimes it can be made. Could you please help analyze the possible reasons or check the as...
Directly in out/target/product/smdkv210/system/build.prop:ro.sf.lcd_density=240 Then directly use make_ext4fs to package. ./make_ext4fs -l 120M -a system system.img out/target/product/smdkv210/system ...
A Beijing embedded enterprise is currently recruiting the following development and testing personnel on a long-term basis. The basic requirements are: more than 3 years of LINUX kernel development or...
I am currently studying the Internet of Things at school. My project is water quality monitoring. We use the STM32F103vet6 industrial control board and the development environment is keil4. There is a...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
Introduction
X1226 has the functions of clock and calendar. The clock relies on hour, minute and second registers to track, and the calendar relies on date, week, month and year registers to tr...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
