202408B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • January 25, 2013
DATA SHEET
AAT3215
150mA CMOS High Performance LDO
Absolute Maximum Ratings
1
T
A
= 25°C, unless otherwise noted.
Symbol
V
IN
V
ENIN(MAX)
I
OUT
T
J
Description
Input Voltage
Maximum EN to Input Voltage
DC Output Current
Operating Junction Temperature Range
Value
6
0.3
P
D
/(V
IN
-V
O
)
-40 to 150
Units
V
mA
°C
Thermal Information
2
Symbol
θ
JA
P
D
Description
Maximum Thermal Resistance
Maximum Power Dissipation
Rating
190
526
Units
°C/W
mW
Recommended Operating Conditions
Symbol
V
IN
T
Description
Input Voltage
Ambient Temperature Range
Rating
(V
OUT
+ 0.3) to 5.5
-40 to +85
Units
V
°C
1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions
"EZ-USB FX2 MCU Principle, Programming and Development Application" Edited by Qian Feng, Beijing University of Aeronautics and Astronautics Press. Does anyone have the electronic version or download a...
I looked at a circuit diagram for making MP3 on the Internet and encountered a problem with headphones. There are two headphone bases in the circuit diagram, and the connection methods are different, ...
Switching power supplies, charge pumps, LDOs
The efficiency of DC-DC or charge pump circuit is higher than that of LDO or other linear step-down circuits. Does anyone have a deeper understanding and c...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:00[/i]No matter from which aspect, the first choice for electronic engineering students to study abroad should be the United States. What doe...
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
The program got stuck during LCD initialization. Through hardware debugging, it was found that it was stuck in the Delay_ms() function. Going to the definition, it was found to be a macro definition ...[Details]
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
When designing a product, if the application environment's requirements for power isolation are not considered, the product will be unstable due to improper design, and even high voltage may damage t...[Details]
This paper combines embedded control technology with network control technology to realize the design of temperature control system based on single chip microcomputer through Internet control. Th...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
Household photovoltaic power stations mainly utilize idle resources on existing household buildings, such as roofs, wall facades, balconies, courtyards, etc., to install and use distributed photovo...[Details]
12864 LCD parallel port driver is more commonly used, but considering that sometimes the IO port of the microcontroller or MCU is limited, the serial driver method can be used. The following is ...[Details]
This program sets the LED running light and the 0-16 numbers of the 0th position of the digital tube to light up in a cycle. The digital tube program cannot be put into the main function, because the...[Details]
Use common anode digital tube and independent keyboard to connect P1 and P2 ports of single chip to realize answering machine The procedure is as follows: #include reg52.h void delay(unsigned char n)...[Details]
The circuit shown in the figure requires that the light is off when the machine is turned on. Press the button once, and the light D1 will turn on and automatically turn off after a delay of 10 secon...[Details]
Assume that both the augend NA and the addend NB are three-byte compressed BCD codes, which are stored in the internal RAM units 20H~22H and 30H~32H, respectively, with the low digit first and the hi...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
