EXPOSED PAD (PIN 9) IS OUT, MUST BE SOLDERED TO OUT ON
THE PCB; SEE THE APPLICATIONS INFORMATION SECTION
ST PACKAGE
3-LEAD PLASTIC SOT-223
T
JMAX
= 125°C,
θ
JA
= 24°C/W,
θ
JC
= 15°C/W
TAB IS OUT, MUST BE SOLDERED TO OUT ON THE PCB;
SEE THE APPLICATIONS INFORMATION SECTION
TS8 PACKAGE
8-LEAD PLASTIC TSOT-23
T
JMAX
= 125°C,
θ
JA
= 57°C/W,
θ
JC
= 15°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT3082EDD#PBF
LT3082IDD#PBF
LT3082EST#PBF
LT3082IST#PBF
LT3082MPST#PBF
LT3082ETS8#PBF
LT3082ITS8#PBF
LEAD BASED FINISH
LT3082EDD
LT3082IDD
LT3082EST
LT3082IST
LT3082MPST
LT3082ETS8
LT3082ITS8
TAPE AND REEL
LT3082EDD#TRPBF
LT3082IDD#TRPBF
LT3082EST#TRPBF
LT3082IST#TRPBF
LT3082MPST#TRPBF
LT3082ETS8#TRPBF
LT3082ITS8#TRPBF
TAPE AND REEL
LT3082EDD#TR
LT3082IDD#TR
LT3082EST#TR
LT3082IST#TR
LT3082MPST#TR
LT3082ETS8#TR
LT3082ITS8#TR
PART MARKING*
LDYT
LDYT
3082
3082
3082MP
LTDYV
LTDYV
PART MARKING*
LDYT
LDYT
3082
3082
3082MP
LTDYV
LTDYV
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
8-Lead Plastic SOT-23
8-Lead Plastic SOT-23
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
8-Lead Plastic SOT-23
8-Lead Plastic SOT-23
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–40°C to 125°C
–40°C to 125°C
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–55°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3082f
2
LT3082
ELECTRICAL CHARACTERISTICS
PARAMETER
SET Pin Current
Offset Voltage (V
OUT
– V
SET
)
Load Regulation (Note 7)
Line Regulation
Minimum Load Current (Note 3)
Dropout Voltage (Note 4)
Current Limit
Error Amplifier RMS Output Noise (Note 5)
Reference Current RMS Output Noise (Note 5)
Ripple Rejection
I
SET
V
OS
ΔI
SET
ΔV
OS
ΔI
SET
ΔV
OS
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
J
= 25°C. (Note 2)
CONDITIONS
V
IN
= 2V, I
LOAD
= 1mA
2V ≤ V
IN
≤ 40V, 1mA ≤ I
LOAD
≤ 200mA
V
IN
= 2V, I
LOAD
= 1mA
V
IN
= 2V, I
LOAD
= 1mA
ΔI
LOAD
= 1mA to 200mA
ΔI
LOAD
= 1mA to 200mA
ΔV
IN
= 2V to 40V, I
LOAD
= 1mA
ΔV
IN
= 2V to 40V, I
LOAD
= 1mA
2V ≤ V
IN
≤ 40V
I
LOAD
= 10mA
I
LOAD
= 200mA
V
IN
= 5V, V
SET
= 0V, V
OUT
= –0.1V
,
I
LOAD
= 200mA, 10Hz ≤ f ≤ 100kHz, C
OUT
= 10μF
C
SET
= 0.1μF
10Hz ≤ f ≤ 100kHz
f = 120Hz, V
RIPPLE
= 0.5V
P-P
, I
LOAD
= 0.1A,
C
OUT
= 2.2μF C
SET
= 0.1μF
,
f = 10kHz
f = 1MHz
I
SET
10ms Pulse
l
l
l
l
l
l
l
MIN
9.90
9.80
–2
–4
TYP
10
10
MAX
10.10
10.20
2
4
UNITS
μA
μA
mV
mV
nA
mV
nA/V
mV/V
μA
V
V
mA
μV
RMS
nA
RMS
dB
dB
dB
%/W
–0.1
–0.5
0.03
0.003
300
1.22
1.3
200
300
33
0.7
90
75
20
0.003
–2
0.2
0.010
500
1.45
1.65
Thermal Regulation
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Unless otherwise specified, all voltages are with respect to V
OUT
.
The LT3082E is tested and specified under pulse load conditions such
that T
J
≅
T
A
. The LT3082E is 100% tested at T
A
= 25°C. Performance at
–40°C and 125°C is assured by design, characterization, and correlation
with statistical process controls. The LT3082I is guaranteed to meet all
data sheet specifications over the full –40°C to 125°C operating junction
temperature range. The LT3082MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 3:
Minimum load current is equivalent to the quiescent current of
the part. Since all quiescent and drive current is delivered to the output
of the part, the minimum load current is the minimum current required to
maintain regulation.
Note 4:
For the LT3082, dropout is specified as the minimum input-to-
output voltage differential required supplying a given output current.
Note 5:
Adding a small capacitor across the reference current resistor
lowers output noise. Adding this capacitor bypasses the resistor shot
noise and reference current noise; output noise is then equal to error
amplifier noise (see the Applications Information section).
Note 6:
Diodes with series 1k resistors clamp the SET pin to the OUT pin.
These diodes and resistors only carry current under transient overloads.
Note 7:
Load regulation is Kelvin-sensed at the package.
Note 8:
This IC includes overtemperature protection that protects the
device during momentary overload conditions. Junction temperature
exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
My system now needs 12V DC power supply, but for the sake of safety, I use two independent 12V power supply paths. When any of the power supplies is powered off, the other power supply immediately tak...
[i=s] This post was last edited by chun912 on 2017-5-11 14:23 [/i] [b]Article Abstract: [/b] I recently spent a huge amount of money to buy a set of FPGA development boards from Taobao. The first thin...
This is the SAM module of a water-soaked Mercedes-Benz car, and it looks clean on the outside.Judging from the label, it is produced by Hella and made in Romania.From the side, there is a lot of dried...
When you long press a Button, a prompt box will appear at the clicked position. I now want to intercept the long press Button message. I am developing with MFC. Can an expert tell me what this message...
[i=s]This post was last edited by Hot Ximixiu on 2021-3-28 09:50[/i]1. The RESET pin can be reused as a GPIO digital input port with pull-up. It is recommended to retain the peripheral reset circuit;
...
Laptops are no longer the expensive gadgets they were 10 years ago. They have become a must-have for business trips, entertainment, and family life. What laptops do students, engineers, and business t...
While
the solid-state battery
industry is still engaged in a long technological marathon for
the "ultimate solution" for
electric vehicles
, some companies have begun looking for mor...[Details]
For autonomous vehicles to safely navigate the road, they must identify far more complex objects than just traffic lights, pedestrians, and other familiar objects. Among these obstacles is a crucia...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
1. Fault phenomenon and cause analysis
1. During the operation of the equipment, the expansion sleeve is subjected to a large torque, and the mating surfaces of the shaft and the sleeve move...[Details]
In the field of communications power supplies, AC/DC rectifier power supplies are called primary power supplies or basic power supplies, while DC/DC converters are called secondary power supplies. ...[Details]
Previously, Positive Motion Technology shared with you the firmware upgrade of motion controller, ZBasic program development, ZPLC program development, communication with touch screen and input/out...[Details]
introduction
In recent years, multi-touch has emerged as a new alternative to traditional human-computer interaction. It eliminates the need for keyboards and mice, enabling simultaneous inter...[Details]
01. Introduction
As in-vehicle networks migrate from the CAN
bus
to
Ethernet
, traditional millisecond-level synchronization accuracy can no longer meet the requirements of mul...[Details]
With the growth of the Internet of Things (IoT), wearable, and portable devices, consumers are growing weary of cluttered cables and the need for frequent battery recharges. The benefits of wireles...[Details]
As the core of electric vehicles, batteries are concerned with vehicle use and maintenance. The operation of vehicles is guaranteed by the electricity generated by batteries. For batteries, battery...[Details]
As automotive technology develops at an ever-increasing pace, the performance requirements for automotive internal structures, components, and accessories are becoming increasingly demanding. The d...[Details]
Thoughts triggered by the Wuhan Radish Run incident
It's so hot, even Ferraris spontaneously combust. A recent incident on a Wuhan overpass: a red Ferrari...[Details]
introduction
Due to their flexibility and security, Java cards are increasingly being used in the smart card field. Once a Java card is released, if multiple applications need to call the same...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
