DTS24Z21-39PB [V001] datasheet, PDF

DTS24Z21-39PB [V001]: DescriptionRECP ASSY; CategoryThe connector; File Size856KB，17 Pages; ManufacturerTE Connectivity; Websitehttp://www.te.com

Download Datasheet Parametric View All

DTS24Z21-39PB [V001] Overview

RECP ASSY

Parameter Name	Attribute value
Connector System	line to panel, line to panel
Sealable	yes
Connectors and terminals terminate to	Wires and cables
Housing size	21
shield	yes
Connector type	female end, female end
Housing type	Lock nut female end
Number of Positions	39
Number of power supply locations	2
Number of signal positions	37
Pre-installed	no
Shell plating material	black zinc nickel alloy
Shell material	Aluminum 6061-T6
Insulation Materials	Hard dielectric/silica gel
Sealed	no
Contact Current Rating (Max) (A)	13
reverse polarity	no
Terminal layout	21 – 39
Terminal type	Pin
Connector mounting type	Panel
polar code	B
Joint alignment type	keying
joint fixation	with
Location monitoring	Timing
Cable size	.52 – 1.31 mm² [ 20 – 16 AWG ]
Working group temperature range	-65 – 200 °C [ -85 – 392 °F ]
Circuit Application	Power and Signal

ADS8332 Question 2: Where does this interference come from?: I used C2000's SPI to drive ADS8332. I've had success in the past, but it was on a different PCB. However, when I tried it again, I ran into a lot of problems. [/font] Phenomenon: When the sampling an...; dontium Analogue and Mixed Signal

I would like to ask about the timer interrupt problem (I have been unable to find any information, please give me some advice): Question 1: Is it necessary to install the initial value of the timer in the main function? I seem to have tried it and it works fine without it. Question 2: If timer 0 is turned off in timer 1, do I ...; 唐菲远 51mcu

How to implement the 20-bit address pointer of MSP430FG461X series in C language?: When I assign a 20-bit address 0x10000 to a pointer variable, it always says that it is out of the range of 0 to 0xFFFF.This is possible in assembly language, because MSP430X provides instructions wit...; 我爱电子 Microcontroller MCU

Crystal oscillator problem: Please help me analyze this:the crystal oscillator is not working properly. It does not oscillate at first. Then I touch it with a soldering iron and it works normally for a while. Then it does not os...; chenzep Microcontroller MCU

Regarding the issue of running programs under pure DOS on the PC104 device, is there any difference between the pure DOS booted by the virtual floppy drive and the actually installed DOS?: As the title says. Now the program runs in pure DOS booted by virtual floppy drive. The program written in 2000 with bc31 runs smoothly in 2000, but it is very stuck in DOS. I want to compile it in DO...; lionedwolf Embedded System

[Transfer] Basic knowledge of WIFI and 802.11 protocol: [align=left] [/align][align=left][b]I. Basic Overview[/b][/align][align=left]===============================[/align][align=left][b]1[/b][b]Wired and wireless networks[/b][/align][align=left]At present...; dontium RF/Wirelessly

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components