EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

DTS26Z21-16HB [V001]

Description
PLUG ASSY
CategoryThe connector   
File Size856KB,17 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

DTS26Z21-16HB [V001] Overview

PLUG ASSY

DTS26Z21-16HB [V001] Parametric

Parameter NameAttribute value
Connector Systemline to panel, line to panel
Sealableyes
Connectors and terminals terminate toWires and cables
Housing size21
shieldyes
Connector typeplug
Housing typestraight plug
Number of Positions16
Number of power supply locations16
Number of signal positions0
Pre-installedno
Shell plating materialblack zinc nickel alloy
Shell materialAluminum 6061-T6
Insulation MaterialsHard dielectric/silica gel
Sealedno
Contact Current Rating (Max) (A)13
reverse polarityno
Terminal layout21 – 16
Terminal typePin
Connector mounting typePanel
polar codeB
Joint alignment typekeying
joint fixationwith
Location monitoringTiming
Cable size.52 – 1.31 mm² [ 20 – 16 AWG ]
Working group temperature range-65 – 200 °C [ -85 – 392 °F ]
Circuit ApplicationPower
[Help] Interrupt compilation cannot pass! !
#includeinterrupt[TIMERA0_VECTOR] void Timer_A(void){~~~}void InitSystem(void){~~~//TIME_ATACTL=ID1+TASSEL1+TACLR+MC0; //devider:8; use SMCLK ;mode:compare;CCTL0=CCIE; //interrupt ena××eCCR0=1000; //1...
zhang124 Microcontroller MCU
Where can I find the design of the ward call system?
May I ask where can I find the design of the ward call system? I need it urgently~[:'(]...
zhangdong158 MCU
Problems caused by stepping up the power supply and then stepping it down to connect it to the power supply
Due to product requirements, difficult problems have arisen in circuit design. For example: a 12v battery is connected to a DC-DC boost circuit, and the voltage rises to 18v. The output is then connec...
jyz520 Analog electronics
The function calculation results in Dsplib are inconsistent with those in Matlab?
The development board I use is TMS320C5535. I want to do convolution operation. The convolution function I wrote takes too long to calculate, so I use the convol1 function in Dsplib instead. Test data...
Changhong DSP and ARM Processors
Can Altium implement the function of the network label indicator page?
[size=6][backcolor=yellow]As shown in the figure above, there is a 5 after LED1, which means it is connected to page 5[/size][/backcolor][backcolor=yellow][size=6][backcolor=rgb(255, 255, 0)][size=6]A...
flying510 PCB Design
A word of caution when grounding ADC outputs
[i=s]This post was last edited by qwqwqw2088 on 2016-5-19 10:12[/i] Although many converters have tri-state outputs/inputs, these registers are still on-chip; they allow data pin signals to couple int...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1866  1774  2340  653  1994  38  36  48  14  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号