Resistance to sulphur-bearing gas (AS version only): ASTM-B-809
Voltage proof
Volts
Note: A 0.01 Ohm addition to be added to the performance of all resistors <10 Ohms.
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
1
1
1
0.25
0.25
0.25
500
ΔR%
ΔR%
Maximum
1
0.1
Zero at 155°C
0.1
0.2
0.25
0.05
0.05
0.05
Typical
0.25
0.02
Pulse Performance Data
Pulse Performance Data
Lightning Surge
Lightning surge resistors are tested in accordance with IEC 60 115-1 using both 1.2/50µs and 10/700µs pulse shapes. 10 pulses are applied. The limit of
acceptance is a shift in resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Lightning Surge
Lightning surge resistors are tested in
accordance with IEC 60 115-1 using
both 1.2/50µs and 10/700µs pulse shapes.
10 pulses are applied. The limit of
acceptance is a shift in resistance of less
than 1% from the initial value.
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
The single impulse graph is the result of 50 impulses of rectangular shape applied at one minute intervals. The limit of acceptance was a shift in
resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Continuous Load Due to Repetitive Pulses
The continuous load graph was obtained by applying repetitive rectangular pulses where the pulse period was adjusted so that the average
power dissipated in the resistor was equal to its rated power at 70°C. Again the limit of acceptance was a shift in resistance of less than 1% from the
initial value
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
Is anyone using the STM32L152 series MCU? I want to ask a question. I want to do low power consumption now, so I need to enter Stop mode. But I read a book and it says that entering Stop mode will tur...
c=sizeof(USB_CONFIGURATION_DESCRIPTOR) + sizeof(USB_INTERFACE_DESCRIPTOR) + (NUM_ENDPOINTS * sizeof(USB_ENDPOINT_DESCRIPTOR));If you write it like this on the IAR compiler, an error will be reported. ...
I tried the Ethernet upgrade code provided by everyone in the forum, but it failed to test. Which boss can provide a simple bootloader test code for the Ethernet upgrade program? Thank you!...
The key to the oscillator IIBLC meter is the oscillation circuit shown in Figure 1. LM311 is a voltage comparator. When the power is applied, the second pin of LM311 is 2.5V due to the voltage divider...
Phase shifter is a regulating is widely used in signal processing and instrument measurement. In the past, phase shifters were generally composed of a 12-sided phase shift circuit with three-phase inp...
Add a resettable fuse to the DC circuit to protect the circuit. I usually connect the fuse to the positive terminal of the power supply, but I think it can also be connected to the negative terminal o...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
FPGAs are used in 81% of electronic systems, including many commercial and defense products, and most FPGAs use BGA packaging. The BGA packaging is characterized by small solder balls and small sol...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
Against the backdrop of global warming, energy conservation and emission reduction have become a global hotspot and focus, which has also sounded the clarion call for the take-off of the LED lighti...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
