April 19, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 204379B
DATA SHEET • RFX2411: 2.4 GHz TRANSMIT/RECEIVE ZIGBEE
®
RFEIC WITH DIVERSITY SWITCH
Electrical and Mechanical Specifications
The absolute maximum ratings of the RFX2411 are provided in
Table 2. The recommended operating conditions are specified
in Table 3.
The TX/RX/Bypass mode electrical specifications are provided in
Table 4. The state of the RFX2411 is determined by the logic
provided in Table 5.
Table 2. RFX2411 Absolute Maximum Ratings
1
Parameter
DC VDD voltage supply
DC control pin voltage
DC VDD current consumption
TX RF input power
ANT RF RX input power
ANT RF RX input power
Junction temperature
No RF and DC voltages applied
Storage ambient temperature
Electrstatic discharge:
Human Body Model (HBM)
Appropriate care required according
to JEDEC Standards
ESD HBM
–50
+150
°C
V
LNA mode
Bypass mode
All VDD pins
Through 1 kΩ resistor
Through VDD pins when TX is ON
Conditions
Minimum
0
0
Maximum
4.0
3.6
350
+5
+5
+16
+150
Units
V
V
mA
dBm
dBm
dBm
°C
> 1000
1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters
set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. All maximum RF input power ratings assume 50
Ω
terminal
impedance.
ESD HANDLING:
Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device.
This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce
potentials of several kilovolts on the human body or equipment, which can discharge without detection.
Industry-standard ESD handling precautions should be used at all times.
Table 3. RFX2411 Recommended Operating Conditions
1
Parameter
DC VDD voltage supply
1
Control voltage high
Control voltage low
DC control pin current consumption
DC shutdown current
PA turn-on/turn-off time
LNA turn on/turn-off time
Antenna switch time
Operating ambient temperature
DC VDD voltage supply
1
ja
See note 2
2.0
–40
35
3.3
3.6
All VDD pins
RXEN, TXEN, and MODE pins
RXEN, TXEN, and MODE pins
See note 2
Conditions
Minimum
2.0
1.2
0
1
300
1
1
1
+125
Typical
3.3
Maximum
3.6
VDD
0.3
Units
V
V
V
μA
nA
μsec
μsec
μsec
°C
°C/W
V
1 For normal operation of the RFX2411, VDD must be continuously applied to all VDD supply pins.
2 For operation above +85
o
C, use the
ja
as guidance for system design to assure the junction temperature will not exceed the maximum of +150
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:02[/i] To realize UPS battery intelligent management, multiple aspects need to be considered, among which the most important are intell...
I made the minimum 430 system board by myself, but when I run the clock initialization program below, I can't exit. What is the reason?
void Init_CLK() {uchar i;BCSCTL1 = ~XT2OFF; //Turn on XT oscilla...
Solve y=(ax^2-bx+c)/(dx+e) by programming, and put the quotient and remainder in the data memory 1000H and 1001H respectively. (1) Given a=8, b=6, c=10, d=7, e=9, x=5, find y. (2) Given a=0.9, b=0.1, ...
There is a junior girl who has to hand in her graduation project this week. Now I have broken down her graduation project into a few simple sentences.
It is 1838 infrared receiver and LED infrared tra...
I am using CodeWarrior version 6.2. Now I want to program mm908E624, but I can't find mm908E624 in CodeWarrior. Should I choose MC68HC908EY16 as the chip, because the core of mm908E624 is MC68HC908EY1...
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
Mobile and portable
京公网安备 11010802033920号
EEWORLD
