TDF8546
I
2
C-bus controlled 4
45 W best efficiency amplifier
Rev. 8 — 27 September 2013
Product short data sheet
1. General description
The TDF8546 is one of a new generation of complementary quad Bridge-Tied Load (BTL)
audio power amplifiers intended for automotive applications. It has a best efficiency mode
with full I
2
C-bus controlled diagnostics, including start-up diagnostics. The TDF8546 can
operate at a battery voltage as low as 6 V making this amplifier suitable for stop/start-car
operation.
The new best efficiency principle uses a patented switch technique which reduces
switching distortion. To reduce power dissipation, the new best efficiency principle uses
the audio information on all four channels instead of only the front or rear signals.
Dissipation is more than 65 % less than standard BTL when used for front and rear
correlated audio signals. Dissipation is 35 % less than standard BTL when used for
uncorrelated (delayed) audio signals between front and rear. It is 17 % less for
uncorrelated audio signals when the front or rear information is used.
The amplifier uses a complementary DMOS output stage in a Silicon-On-Insulator (SOI)
based BCD process. The DMOS output stage ensures a high-power output signal with
perfect sound quality. The SOI-based BCD process ensures a robust amplifier, where
latch-up cannot occur, with good separation between the four independent channels, with
every component isolated and without substrate currents.
2. Features and benefits
Stop/start-car prepared: keeps operating without audible disturbance during engine
start at a battery voltage as low as 6 V
New best efficiency mode with patented low switching distortion
Extreme best efficiency mode (uses information from 4 channels) with 17 % less
dissipation for uncorrelated signals compared to 2-channel best efficiency mode.
Operates in either legacy (non-I
2
C-bus) or I
2
C-bus modes (3.3 V and 5 V compliant)
Four hardware-programmable I
2
C-bus addresses
Can drive 2
and 4
loads
Speaker fault detection
Start-up diagnostics with load detection: open, short, present; filtered for door-slam
and chatter relays
AC load (tweeter) detection with low and high current mode
Gain select after start-up without audible disturbance
Independent selectable soft mute of front and rear channels
Programmable gain (26 dB and 16 dB), independently programmable for the front and
rear channels
NXP Semiconductors
TDF8546
I
2
C-bus controlled 4
45 W best efficiency amplifier
Line driver mode supports engine start at a battery voltage as low as 6 V (16 dB and
mid-tap voltage 0.25
V
P
)
Programmable clip detect: 2 %, 5 % or 10 %
Programmable thermal pre-warning
Pin STB can be programmed/multiplexed with second-clip detect
Clip information of each channel can be directed separately to pin DIAG or pin STB
Independent enabling of thermal-, clip- or load fault information (short across the load
or to V
P
or to ground) on pin DIAG
Loss-of-ground and open V
P
safe (minimum series resistance required)
All amplifier outputs short-circuit proof to ground, supply voltage and across the load
(channel independent)
All pins short-circuit proof to ground
Temperature controlled gain reduction to prevent audio holes at high junction
temperatures
Programmable low battery voltage detection to enable 7.5 V or 6 V minimum battery
voltage operation
Overvoltage protection (load-dump safe up to V
P
= 50 V) with overvoltage pre-warning
at 16 V
Offset detection
3. Quick reference data
Table 1.
V
P(oper)
I
q
P
o
Quick reference data
Conditions
R
L
= 4
no load
no load; V
P
= 7 V
output power
R
L
= 4
;
V
P
= 14.4 V; maximum power;
V
i
= 2 V RMS square wave
R
L
= 4
;
V
P
= 15.2 V; maximum power;
V
i
= 2 V RMS square wave
R
L
= 4
;
V
P
= 14.4 V; THD = 0.5 %
R
L
= 4
;
V
P
= 14.4 V; THD = 10 %
R
L
= 2
;
V
P
= 14.4 V; THD = 10 %
R
L
= 2
;
V
P
= 14.4 V; maximum power;
V
i
= 2 V RMS square wave
THD
V
n(o)
total harmonic
distortion
output noise voltage
P
o
= 1 W to 12 W; f
i
= 1 kHz; R
L
= 4
;
BTL mode
P
o
= 4 W; f
i
= 1 kHz; R
L
= 4
;
best efficiency mode
filter 20 Hz to 22 kHz; R
S
= 1 k
amplifier mode
line driver mode
-
-
43
25
65
33
V
V
Min
6
-
-
37
41
18
23
40
58
-
-
Typ
14.4
260
190
40
45
20
25
44
64
0.01
0.03
Max
18
350
-
-
-
-
-
-
-
0.1
-
Unit
V
mA
mA
W
W
W
W
W
W
%
%
operating supply
voltage
quiescent current
Symbol Parameter
TDF8546_SDS
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product short data sheet
Rev. 8 — 27 September 2013
2 of 21
NXP Semiconductors
TDF8546
I
2
C-bus controlled 4
45 W best efficiency amplifier
4. Ordering information
Table 2.
Ordering information
Package
Name
TDF8546J
TDF8546TH
TDF8546JS
DBS27P
HSOP36
DBSMS27P
Description
plastic DIL-bent-SIL (special bent) power package;
27 leads (lead length 6.8 mm)
plastic, heatsink small outline package; 36 leads; low stand-off height
plastic dual bent surface mounted SIL power package; 27 leads
Version
SOT827-1
SOT851-1
SOT1154-1
Type number
TDF8546_SDS
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product short data sheet
Rev. 8 — 27 September 2013
3 of 21
NXP Semiconductors
TDF8546
I
2
C-bus controlled 4
45 W best efficiency amplifier
5. Pinning information
5.1 Pinning
ADSEL
STB
PGND2
OUT2-
DIAG
OUT2+
V
P2
OUT1-
PGND1
1
2
3
4
5
6
7
8
9
OUT1+ 10
SVR 11
IN1 12
IN2 13
SGND 14
IN4 15
IN3 16
ACGND 17
OUT3+ 18
PGND3 19
OUT3- 20
V
P1
21
OUT4+ 22
SCL 23
OUT4- 24
PGND4 25
SDA 26
TAB 27
TDF8546J/JS
aaa-005789
Fig 1.
Pin configuration of TDF8546J/JS (packages DBS27P and DBSMS27P)
TDF8546_SDS
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product short data sheet
Rev. 8 — 27 September 2013
4 of 21
NXP Semiconductors
TDF8546
I
2
C-bus controlled 4
45 W best efficiency amplifier
TAB 36
n.c. 35
n.c. 34
n.c. 33
PGND3 32
n.c. 31
ACGND 30
IN3 29
IN4 28
SGND 27
IN2 26
IN1 25
SVR 24
PGND1 23
n.c. 22
n.c. 21
n.c. 20
n.c. 19
001aam684
1
2
3
4
5
6
7
8
OUT3-
OUT3+
V
P1
OUT4-
PGND4
OUT4+
SCL
SDA
DIAG
TDF8546TH
9
10 ADSEL
11 STB
12 n.c.
13 OUT2+
14 PGND2
15 OUT2-
16 V
P2
17 OUT1+
18 OUT1-
Fig 2.
Pin configuration TDF8546TH
TDF8546_SDS
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product short data sheet
Rev. 8 — 27 September 2013
5 of 21
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
