Accuracy when OUT is connected directly to ADJ. When OUT voltage is set by external feedback resistors, absolute accuracy in adjust mode depends on the tolerances
of resistors used.
2
Based on an end-point calculation using 10 mA and 150 mA loads. See Figure 8 for typical load regulation performance for loads less than 10 mA.
3
Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output
voltages above 2.5 V.
4
Start-up time is defined as the time between the rising edge of EN to OUT being at 90% of its nominal value.
5
Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 1.0 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 1.0 V, or 0.9 V.
Rev. 0 | Page 3 of 16
ADP1710/ADP1711
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
IN to GND
OUT to GND
EN to GND
ADJ/BYP to GND
Storage Temperature Range
Operating Junction Temperature Range
Soldering Conditions
Rating
–0.3 V to +6 V
–0.3 V to IN
–0.3 V to +6 V
–0.3 V to +6 V
–65°C to +150°C
–40°C to +125°C
JEDEC J-STD-020
THERMAL RESISTANCE
θ
JA
is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
5-Lead TSOT
θ
JA
170
Unit
°C/W
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 4 of 16
ADP1710/ADP1711
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
IN
1
GND
2
06310-004
ADP1710
FIXED
TOP VIEW
(Not to Scale)
5
OUT
IN
1
GND
2
ADP1710
ADJUSTABLE
TOP VIEW
(Not to Scale)
5
OUT
IN
1
GND
2
06310-005
ADP1711
TOP VIEW
(Not to Scale)
5
OUT
EN
3
4
NC
EN
3
4
ADJ
EN
3
4
BYP
NC = NO CONNECT
Figure 4. 5-Lead TSOT (UJ-Suffix)
Figure 5. 5-Lead TSOT (UJ-Suffix)
Figure 6. 5-Lead TSOT (UJ-Suffix)
Table 4. Pin Function Descriptions
ADP1710
Fixed
Pin No.
1
2
3
4
4
4
5
5
5
ADP1710
Adjustable
Pin No.
1
2
3
ADP1711
Pin No.
1
2
3
Mnemonic
IN
GND
EN
NC
ADJ
BYP
OUT
Description
Regulator Input Supply. Bypass IN to GND with a 1 μF or greater capacitor.
Ground.
Enable Input. Drive EN high to turn on the regulator; drive it low to turn off the
regulator. For automatic startup, connect EN to IN.
No Connect.
Adjust. A resistor divider from OUT to ADJ sets the output voltage.
Connect a 1 nF or greater capacitor (10 nF is recommended) between BYP and GND
to reduce the internal reference noise for low noise applications.
Regulated Output Voltage. Bypass OUT to GND with a 1 μF or greater capacitor.
Please advise all the prawns:
For example, I have a text document on my computer with a line of numbers on it: 1 0 3. 1 represents the address of the microcontroller, 0 represents the forward and reve...
At the beginning of the school year:One week after the start of school:Two weeks after the start of school:
－－－－－－－－－－－－－－－－－－－－－－－－－－－－
Before midterm exam: Midterm exam: 1 day after midterm exam:
－－...
A newbie needs help... Experts, please give me some advice...I have been studying the FATFS file system these days . I searched online and found that it can be ported to various microcontrollers such ...
When welding small metals, sometimes tin can't solve the problem, so spot welding comes to mind. Now I found a transformer:It looks powerful. The secondary of this transformer is 12V output and uses a...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
1. Introduction
Stepper motor is a basic component that converts electrical energy into kinetic energy. It has been widely used in a variety of electromechanical equipment, such as various machine...[Details]
I. Introduction
The use of electronics in cars dates back to the early 20th century when electric starters replaced hand cranks. Automotive electronics became popular in the 1960s with the...[Details]
1. Basic principles of organic/polymer solar cells
The basic principle of organic/polymer solar cells is to use the photovoltaic effect generated by light incident on the heterojunction of sem...[Details]
As a type of iron battery, lithium iron phosphate battery (hereinafter referred to as lithium iron battery) has always been widely concerned by industry friends (some people say that lithium iron b...[Details]
PID is proportional differential adjustment. You can refer to the detailed introduction in the automatic control course for details! The positive action and the negative action in temperature contr...[Details]
1 Theoretical Analysis
Ultrasonic waves
When propagating in a suspension, the ultrasonic waves that encounter the suspended particles are scattered and attenuated at the interface, an...[Details]
1 Introduction
The early stage control system used relay control. Due to the large number of stage equipment, the number of control elements is huge and the wiring is complicated. Therefore, th...[Details]
illustrate]
This method has
the characteristics of small
ROM
occupation
and fast operation speed, with a range of
2000
ßà
2099
,
a total of
...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
