No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condition, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V, 3.3V, ST = GND, output is Weakly Pulled Down
Vdd = 1.8V, ST = GND, output is Weakly Pulled Down
See the Absolute Pull Range and APR table on
page 10
Vdd = 1.8V, Voltage at which maximum deviation is guaranteed.
Vdd = 2.5V, Voltage at which maximum deviation is guaranteed.
Vdd = 2.8V, Voltage at which maximum deviation is guaranteed.
Vdd = 3.3V, Voltage at which maximum deviation is guaranteed.
Voltage at which minimum deviation is guaranteed.
Additional supply voltages between 2.5V and 3.3V can be
supported. Contact
SiTime
for additional information.
Condition
Refer to
Table 11
for the exact list of supported frequencies
Inclusive of Initial tolerance
[4]
at 25 °C, and variation over
temperature, rated supply voltage and load.
10 years, 25°C
Extended Commercial
Industrial
Frequency Range
Frequency Stability and Aging
Supply Voltage and Current Consumption
VCXO Characteristics
±25, ±50, ±100, ±150, ±200
1.7
2.4
2.7
3.2
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Capacitance
Linearity
Frequency Change Polarity
Control Voltage Bandwidth (-3dB)
Duty Cycle
Rise/Fall Time
Output High Voltage
VC_L
Z_in
C_in
Lin
–
V_BW
DC
Tr, Tf
VOH
–
45
–
90%
–
100
–
–
–
–
–
–
–
–
5
0.1
Positive slope
8
–
1.5
–
–
–
–
–
0.1
–
–
1
Upper Control Voltage
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
SiTime Corporation
Rev. 1.01
990 Almanor Avenue, Sunnyvale, CA 94085
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 1. Electrical Characteristics
[1, 2, 3]
Parameter
Input Pull-up Impedance
Input Capacitance
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
RMS Phase Jitter (random)
Symbol
Z_in
C_in
T_start
T_oe
T_resume
T_jitt
T_phj
Electrical Specifications
(continued)
Min.
–
–
–
–
–
–
–
–
Typ.
100
5
–
–
7
1.5
2
0.5
Max.
250
–
10
180
10
Jitter
2
3
1
ps
ps
ps
f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 20 MHz, Vdd = 1.8V
f = 20 MHz, Integration bandwidth = 12 kHz to 20 MHz, All Vdds
Unit
kΩ
PF
ms
ns
ms
Condition
For the OE/ST pin for 6-pin devices
For the OE/ST pin for 6-pin devices
See Figure 7 for startup resume timing diagram
f = 40 MHz, all Vdds. For other freq, T_oe = 100 ns + 3 clock
periods
See Figure 8 for resume timing diagram
Input Characteristics
Startup and Resume Timing
Notes:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
2. The typical value of any parameter in the Electrical Characteristics table is specified for the nominal value of the highest voltage option for that parameter and at
25 °C temperature.
3. All max and min specifications are guaranteed across rated voltage variations and operating temperature ranges, unless specified otherwise
4. Initial tolerance is measured at Vin = Vdd/2
5. Absolute Pull Range (APR) is defined as the guaranteed pull range over temperature and voltage.
6. APR = pull range (PR) - frequency stability (F_stab) - Aging (F_aging)
Rev. 1.01
Page 2 of 11
www.sitime.com
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 2. Pin Description. 4-Pin Configuration
(For 2.5 x 2.0 mm and 3.2 x 2.5 mm packages)
Pin
1
2
3
4
Symbol
VIN
GND
CLK
VDD
Input
Power
Power
Input
Power
Electrical ground
Power supply voltage
Oscillator output power
[7]
GND
2
3
Top View
Functionality
VIN
1
4
0-Vdd: produces voltage dependent frequency change
VDD
CLK
Note:
7. A capacitor value of 0.1 µF between VDD and GND is recommended.
Figure 1.
Table 3. Pin Description. 6-Pin Configuration
(For 5.0 x 3.2 mm and 7.0 x 5.0 mm packages)
Pin
1
Symbol
VIN
Input
No
Connect
2
NC/OE/ ST
Output
Enable
Standby
3
4
5
6
GND
CLK
NC
VDD
Power
Output
No
Connect
Power
Functionality
0-Vdd: produces voltage dependent frequency change
H or L or Open: No effect on output frequency or other device
functions
H or Open
[8]
: specified frequency output
L: output is high
H or Open
[8]
: specified frequency output
L: output is low (weak pull down)
[9]
. Oscillation stops
Electrical ground
Oscillator output
H or L or Open: No effect on output frequency or other device
functions
Power supply
voltage
[10]
VIN
NC/OE/ST
GND
1
6
Top View
VDD
NC
CLK
2
5
3
4
Figure 2.
Notes:
8. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 2 in the 6-pin package is not externally driven. If pin 2 needs to be left floating, use
the NC option
9. Typical value of the weak pull-down impedance is 5 mΩ
10. A capacitor value of 0.1 µF between VDD and GND is recommended.
Table 4. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance of
the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Min.
-65
-0.5
–
–
Max.
150
4
2000
260
Unit
°C
V
V
°C
Table 5. Thermal Consideration
Parameter
7050
5032
3225
2520
JA, 4 Layer Board
(°C/W)
191
97
109
117
JA, 2 Layer Board
(°C/W)
263
199
212
222
JC, Bottom
(°C/W)
30
24
27
26
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Rev. 1.01
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Page 3 of 11
www.sitime.com
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Phase Noise Plot
-100
-110
-120
-130
-140
-150
-160
-170
3
10
Integrated random phase jitter (RMS, 12kHz-5MHz): 0.52ps
[color=#222222]I would like to ask you a question about the error amplifier in the switching power supply loop. Now we need to model this error amplifier. When I was learning analog electronics before...
[i=s]This post was last edited by paulhyde on 2014-9-15 03:46[/i]In a system with strict power consumption requirements, the design of the power supply cannot be completed in a simple way, and the pow...
[size=5]TI's first low-power design competition QQ exchange group: 224276144. Welcome friends who are interested in the competition or are playing with the Wolverine development board (MSP-EXP430FR596...
I was so confused. I spent 20 minutes looking for the error. It turned out that I was not familiar with the compilation environment. I defined ORG 000H JMP MAIN ORG 00CH JMP TIMER0 ORG 008H JMP RC00. ...
I have a 16*16 font library, which is HZK16. But how can I write a program in C language to convert it into the array I need? ? ? Give me some ideas. . . . . . . Thank you...
NLME_GetExtAddr(); Get the 64-bit IEEE address of the device NLME_GetCoordExtAddr(); Get the IEEE address of the parent node of the device There are two functions in the Zstack library to get the IEEE...
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
Introduction
X1226 has the functions of clock and calendar. The clock relies on hour, minute and second registers to track, and the calendar relies on date, week, month and year registers to tr...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
In order to develop lighting LED technology, developed countries attach great importance to the research of LED testing methods and standards. For example, the National Institute of Standards and T...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]
0 Introduction
PROFIBUS is an open digital communication system with a wide range of applications, which has been included in the international standards IEC 61158 and IEC 61784. Since the gen...[Details]
New Automobile
Hydraulic Clutch
The hydraulic control system uses almost 100% advanced engineering plastics, which overcomes the shortcomings of the main and branch cylinders of metal clutc...[Details]
An intelligent vehicle is a robot that can automatically drive in an environment according to a pre-set mode, or it can autonomously perform specific operations according to the on-site situation. ...[Details]
3. Driving circuit design
The power driver uses a field effect tube, which is a field-controlled device with a capacitance effect between the gate and source, so it has high requirements for t...[Details]
As the global leader in virtual instrument technology, NI provided customers with more than 6,000,000 virtual instrument measurement devices in 2004 alone. For 25 years, engineers have used virtual...[Details]
What is Power Monitoring Software
Power monitoring software is used in conjunction with an uninterruptible power supply (UPS) to improve its performance. When using an UPS, users can use this ...[Details]
Tags: PMP Digital Signal Processing
Many observers and analysts agree that there will be only two hot technology topics in the field of electronic engineering and applications this year: o...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
