Operating Temperature Range ...........................-40°C to 125°C
Junction Temperature (Note 1) ........................................+150°C
Storage Temperature Range ...............................-55°C to 150°C
Soldering Temperature (reflow) .......................................+240°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Information
PACKAGE TYPE: 29-PIN SiP
Package Code
Outline Number
Land Pattern Number
Junction to Ambient (θ
JA
)
L29915#1
21-100177
90-100055
24ºC/W
THERMAL RESISTANCE, FOUR-LAYER BOARD
(Note 2)
For the latest package outline information and land patterns (footprints), go to
www.maximintegrated.com/packages.
Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
Note 1:
Junction temperature greater than +125°C degrades operating lifetimes.
Note 2:
Package thermal resistance is measured on an evaluation board with natural convection.
Electrical Characteristics
(V
IN
= V
EN/UVLO
= 24V, R
RT
= OPEN (450kHz), V
PGND
= V
SGND
= V
MODE/SYNC
= 0V, LX = SS =
RESET
= CF = DL = V
CC
= OUT
= open, V
EXTVCC
= 0V, V
BST
to V
LX
= 5V, V
FB
= 1V, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.
All voltages are referenced to SGND, unless otherwise noted.) (Note 3)
PARAMETER
INPUT SUPPLY (V
IN
)
Input-Voltage Range
Input-Shutdown Current
V
IN
I
IN_SH
I
Q_PFM
Input-Quiescent Current
I
Q_DCM
I
Q_PWM
V
EN/UVLO
= 0V, (Shutdown mode)
MODE/SYNC = open
DCM Mode
PWM Mode, no load,
V
OUT
= V
EXTVCC
= 5V
V
EN/UVLO
rising
V
EN/UVLO
falling
Pullup resistor between IN and
EN/UVLO pins
1.185
1.06
3.15
4.5
11
128
1.27
18
2
mA
42
16
V
μA
μA
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
ENABLE/UNDERVOLTAGE LOCKOUT (EN/UVLO)
EN/UVLO Threshold
Enable Pullup Resistor
V
ENR
V
ENF
R
ENP
1.215
1.09
3.32
1.245
1.12
3.45
V
MΩ
www.maximintegrated.com
Maxim Integrated
│
3
MAXM17546
4.5V to 42V, 5A High-Efficiency, DC-DC Step-Down
Power Module with Integrated Inductor
Electrical Characteristics (continued)
(V
IN
= V
EN/UVLO
= 24V, R
RT
= OPEN (450kHz), V
PGND
= V
SGND
= V
MODE/SYNC
= 0V, LX = SS =
RESET
= CF = DL = V
CC
= OUT
= open, V
EXTVCC
= 0V, V
BST
to V
LX
= 5V, V
FB
= 1V, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.
All voltages are referenced to SGND, unless otherwise noted.) (Note 3)
PARAMETER
LOW DROPOUT (INLDO)
V
CC
Output-Voltage
Range
V
CC
Current Limit
IN to V
CC
Dropout
V
CC
UVLO
LOW DROPOUT (EXTVCC)
EXTVCC Operating-
Voltage Range
EXTVCC Switch-Over
Voltage
EXTVCC to V
CC
Dropout
EXTVCC Current Limit
SOFT-START (SS)
Charging Current
OUTPUT SPECIFICATIONS
Line-Regulation Accuracy
Load-Regulation Accuracy
FB-Regulation Voltage
FB Input-Bias Current
FB Undervoltage Trip Level
to Cause Hiccup
HICCUP Timeout
MODE/SYNC PIN
V
M_DCM
MODE Threshold
V
M_PFM
V
M_PWM
SYNC Frequency-
Capture Range
SYNC Pulse Width
SYNC Threshold
V
IH
V
IL
MODE/SYNC = V
CC
(DCM Mode)
MODE/SYNC = OPEN (PFM mode)
MODE/SYNC = GND (PWM mode)
f
SW
set by R
RT
1.1 x
f
SW
50
2.0
0.8
V
CC
- 0.6
V
CC
/ 2
0.6
1.4 x
f
SW
kHz
ns
V
V
V
FB_REG
I
FB
V
FB_HICF
V
IN
= 6.5V to 42V, V
OUT
= 5V
Tested with I
OUT
= 0A to 5A at V
OUT
= 5V
MODE/SYNC = SGND or MODE = V
CC
MODE/SYNC = OPEN
0 < V
FB
< 1V
0.8875
0.8875
-75
0.55
0.58
32768
0.1
6
0.9
0.915
0.9135
0.936
+75
0.61
mV/V
mV/A
V
nA
V
Cycles
I
SS
V
SS
= 0.5V
4.7
5
5.3
μA
V
EXTVCC_DO
Rising
Falling
V
EXTVCC
= 5V, I
EXTVCC
= 45mA
45
85
I
EXTVCC_MAX
V
CC
= 4.3V, EXTVCC = 8V
4.84
4.56
4.33
4.7
4.45
24
4.84
4.6
0.6
140
V
V
V
mA
V
CC
I
VCC_MAX
V
CC_DO
V
CC_UVR
V
CC_UVF
6V < V
IN
< 42V, I
VCC
= 1mA
1mA < I
VCC
< 45mA
V
CC
= 4.3V, V
IN
= 7V
V
IN
= 4.5V, I
VCC
= 45mA
V
CC
rising
V
CC
falling
4.1
3.7
4.2
3.8
4.75
4.75
50
5
5
90
5.25
5.25
150
0.4
4.3
3.9
V
mA
V
V
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
www.maximintegrated.com
Maxim Integrated
│
4
MAXM17546
4.5V to 42V, 5A High-Efficiency, DC-DC Step-Down
Power Module with Integrated Inductor
Electrical Characteristics (continued)
(V
IN
= V
EN/UVLO
= 24V, R
RT
= OPEN (450kHz), V
PGND
= V
SGND
= V
MODE/SYNC
= 0V, LX = SS =
RESET
= CF = DL = V
CC
= OUT
= open, V
EXTVCC
= 0V, V
BST
to V
LX
= 5V, V
FB
= 1V, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.
All voltages are referenced to SGND, unless otherwise noted.) (Note 3)
PARAMETER
CURRENT LIMIT
Average Current-Limit
Threshold
RT PIN
R
RT
= 196KΩ
Switching Frequency
Minimum On-Time
Minimum Off-time
LX Dead Time
RESET
PIN
RESET
Output-Level Low
RESET
Output-Leakage
Current
V
OUT
Threshold for
RESET
Assertion
V
OUT
Threshold for
RESET
Deassertion
RESET
Deassertion Delay
after FB Reaches 95%
Regulation
THERMAL SHUTDOWN
Thermal-Shutdown
Threshold
Thermal-Shutdown
Hystersis
Temperature Rising
165
10
°C
°C
V
OUT_OKF
V
OUT_OKR
f
SW
t
ON(MIN)
t
OFF(MIN)
t
DT
I
RESET
= 10mA
V
RESET
= 5.5V
V
FB
falling
V
FB
rising
-100
90.4
93.4
92.5
95.5
140
22
400
100
94.6
97.7
R
RT
= open
R
RT
= 7.5kΩ
90
420
1950
100
450
2200
114
110
480
2450
160
160
ns
ns
ns
mV
nA
%
%
kHz
I
AVG_LIMIT
6.75
A
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
1024
Cycles
Note 3:
Electrical specifications are production tested at T
A
= + 25°C. Specifications over the entire operating temperature range are
TMS320VC33 is an early DSP product of TI. The development environment we are more exposed to when using TI's DSP is CCS. However, it must be said that the development of VC33 can only be developed in ...
[i=s] This post was last edited by From Getting Started to Giving Up on 2018-8-31 19:15 [/i] From the perspective of resource configuration, processors such as ARM and DSP integrate computing units, s...
How should the power and ground wires be connected in this case? The distance between two adjacent pads is 20mil. They were laid out like this before, but they said it does not meet the specifications...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Analysis of the three core aspects of digital TV transmission standards
According to the differences in regionality, transmission method and modulation method, the transmission method needs to...[Details]
Almost everyone in a student dormitory has a bedside lamp. But if you want to read for a while after turning off the lights and don't want to disturb your roommates' sleep, you may need a reading l...[Details]
The fluorescent lamps and energy-saving lamps we commonly use now have greatly improved luminous efficiency compared with the earlier ordinary incandescent lamps and have been widely used. With the...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems (GP...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
1. Introduction
Modern modular machine tools are equipped with a large number of electronic devices to meet the requirements of processing accuracy, processing speed, etc. If the conventional ...[Details]
Current sensing in automotive applications includes controlling the current through solenoids and injectors. For example, during diesel injection, we rapidly increase the current to the induction i...[Details]
For a long time, hackers have not had the opportunity to enter the control network of the car. But since the advent of Bluetooth technology and the use of wireless LAN bus systems, this situation w...[Details]
With the rapid development of information technology represented by computers, semi-physical simulation technology plays an important role in many military and civilian fields such as aerospace and co...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
