EEWORLDEEWORLDEEWORLD

Part Number

Search

MAX20323EVKIT#

Description
Interface development tool MAX20323 EV KIT
CategoryEmbedded solution    Engineering tools    Analog and digital IC development tools    Interface development tools   
File Size663KB,10 Pages
ManufacturerMaxim
Websitehttps://www.maximintegrated.com/en.html
Environmental Compliance
Download Datasheet Parametric View All

MAX20323EVKIT# Overview

Interface development tool MAX20323 EV KIT

MAX20323EVKIT# Parametric

Parameter NameAttribute value
MakerMaxim
Product CategoryInterface development tools
productEvaluation Kits
typeUSB Type C
Tools for assessmentMAX20323
seriesMAX20323x
Working power voltage2.5 V to 5.5 V
Factory packaging quantity1
MAX20323 Evaluation Kit
Evaluates: MAX20323/MAX20323A/
MAX20323B/MAX20323C/MAX20323D/
MAX20323E/MAX20323F
Quick Start
Required Equipment
MAX20323 EV kit
Power supply
Multimeter
5V power supply or USB cable to power
General Description
The MAX20323 evaluation kit (EV kit) is a fully assembled
and tested circuit board that demonstrates the MAX20323
USB type-C CC-pin overvoltage protection device. The
EV kit comes with the MAX20323ENC+ installed. The
EV kit board can also be used to evaluate MAX20323A/
MAX20323B/MAX20323C/MAX20323D/MAX20323E/
MAX20323F.
Features
Procedure
1)
2)
3)
4)
5)
6)
7)
8)
9)
2.5V to 5.5V Operating Voltage Range
Power LED Reading
Proven PCB Layout
Fully Assembled and Tested
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation:
Connect a 5V power supply to TP14 or connect a
USB cable to J3, verify LED1 is on.
Check the voltage on JU1 pin2 is ~4.3V.
Remove shunt on JU2, check the voltage on JU1
pin2 is ~2.5V.
Remove shunt on JU3, check the voltage on JU1
pin2 is ~1.257V.
Install shunt on JU2, check the voltage on JU1 pin2
is ~3.06V.
Install shunt on JU3 and JU1, check the voltage on
TP11 is ~4.3V.
Connect another power supply 2V to TP3 CC1_I,
check TP9 CC1_O is 2V.
Increase CC1_I voltage, when CC1_I reaches
~5.75V, CC1_O voltage drops down to ~5.1V.
Turn off the power supply on CC1_I, and connect the
power supply to CC2_I TP4.
EV Kit Contents
EV Kit Board Containing a MAX20323
Ordering Information
appears at end of data sheet.
10) Set the power supply to CC2_I to 2V and check
TP10 CC2_O is 2V.
11) Increase CC2_I voltage, when CC2_I reaches
~5.75V, CC2_O voltage drops down to ~5.1V.
319-100046; Rev 0; 7/17
Friends who love running, show off your skills and equipment
[i=s]This post was last edited by mzb2012 on 2017-5-26 22:03[/i] [size=5]I am a 80s guy, based in Shandong, and have been running for three years, on and off. I have now accumulated more than 900 kilo...
mzb2012 Talking
Is this a signal conversion circuit used in a hub?
The signal is input from the left side of the motherboard and output to the computer from the right side. The current situation is that there is a signal on the input side of the optocoupler, but no s...
ena Analog electronics
Let BB Black fly ~ Design of a quadcopter based on BeagleBone Black
I was actually unsure about this. First, I didn’t know if I could get the funds later. Also, software design, hardware design and debugging, and manual welding of many sensors were not easy. I might e...
azhiking DSP and ARM Processors
LaunchPad Development Kit White Paper
LaunchPad Development Kit White Paper...
安_然 Microcontroller MCU
STM8spi issues
What should I pay attention to when using STM8S SPI? The manual says it can reach 10MHZSPI_CR2 = 0X03;SPI_CR1 = 0X4C; //8MHZ (HSE = 16MHZ)while(1){while(!TXE);SPI_DR = 0xAA;}The waveforms measured wit...
碧海沉天 stm32/stm8
Question on whether the decoupling capacitors on the chip can be shared
There are many power pins on a chip, 1.8V and 3.3V respectively. The decoupling capacitor I chose is 104. Can two or more power pins with the same voltage share a decoupling capacitor? Can different v...
逍遥丁敏 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 705  1377  492  1953  1566  15  28  10  40  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号