[i=s] This post was last edited by paulhyde on 2014-9-15 09:30 [/i] The best example for beginners, I hope it is useful to beginners [[i] This post was last edited by liujia1 on 2009-7-26 23:35 [/i]]...
From July 29 to August 18, nearly 20 days have passed. I haven't posted anything and haven't learned much. From 0 to 1 is a very important process, but I haven't gained much from this 1 today. Light u...
I read in the TI user guide that the second pin of JTAG is the power output pin of the emulator, but I see that many people just connect this pin directly to VCC. Why is that? Doesn't this conflict wi...
[p=30, null, center][color=rgb(51, 51, 51)][size=16px][/size][/color][/p][p=30, null, left][color=rgb(51, 51, 51)][size=16px]Although there has been no accident of a drone colliding with an airplane, ...
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
The trade war between China and the United States has become the focus. The United States has begun to play the ban card against Chinese technology companies. The ZTE incident shows that if the ban...[Details]
At the just concluded InfoComm 2018 exhibition, the two major brands, Zhongke Jiguang and China Hualu, both displayed three-color light source
laser TVs
. The outstanding color performance ...[Details]
STM32 uses FSMC to read and write CPLD programs. CPLD is hung on the address line and data line of STM32. CPLD is regarded as an off-chip RAM for reading and writing. On the board I made, CPLD is hun...[Details]
This paper combines embedded control technology with network control technology to realize the design of temperature control system based on single chip microcomputer through Internet control. Th...[Details]
The implementation of CAN driver under embedded operating system Android requires not only adding CAN driver device in Linux kernel, but also implementing the call of Android HAL layer. Taking S5...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
If you do not use an external crystal on the STM32, the connection method of OSC_IN and OSC_OUT If you use the internal RC oscillator instead of an external crystal, please follow the following metho...[Details]
1) ADC multi-channel acquisition: (Multi-channel acquisition must use scanning mode. In scanning mode, the channels of the rule group share a register, so DMA transmission must be used; to prevent da...[Details]
Note: This STM32 microcontroller is the STM32F103 series. The ADC of Stm32 has DMA function. This is beyond doubt and is what we use most! However, if we want to sample a signal (such as a pulse sign...[Details]
This program sets the LED running light and the 0-16 numbers of the 0th position of the digital tube to light up in a cycle. The digital tube program cannot be put into the main function, because the...[Details]
The T3 timer (8-bit) of CC2530 requires understanding of T3CTL, T3CCTL0, T3CC0, T3CCTL1, and T3CC registers. Timer 3/4 is an 8-bit timer with timer/counter/PWM functions. Timer 2, also known as MAC t...[Details]
Using AT89S51 microcontroller, modify the original one to turn the LED on for 4s and off for 2s. Thank you. Use a timer. (The program is written in the answer, omitted here - just a note) The origi...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
