................................................................................................................... -0.6V to 6.5V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature under bias ...............................................................................................................-40°C to +85°C
ESD protection on all pins ........................................................................................................................................≥4 kV
† NOTICE:
Stresses above those listed under ‘Maximum ratings’ may cause permanent damage to the device. This
is a stress rating only and functional operation of the device at those or any other conditions above those indicated in
the operational listings of this specification is not implied. Exposure to maximum rating conditions for an extended
period of time may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
Electrical Characteristics:
Industrial (I):
V
CC
= 1.6V to 5.5V
Characteristic
High-Level Input Voltage
Low-Level Input Voltage
Low-Level Output Voltage
Input Leakage Current
Output Leakage Current
Internal Capacitance
(all inputs and outputs)
Min.
V
CC X
0.7
-0.6
—
—
—
—
—
—
—
—
—
—
—
Max.
V
CC
+ 0.5
V
CC X
0.3
0.4
0.2
±1
±1
±1
7
0.3
1
1
0.5
1.0
Units
V
V
V
V
µA
µA
µA
pF
mA
mA
mA
µA
µA
I
OL
= 2.1 mA, V
CC
= 3.0V
I
OL
= 0.15 mA, V
CC
= 1.8V
V
IN
= V
SS
or V
CC
V
IN
= V
SS
or V
CC
V
OUT
= V
SS
or V
CC
T
AMB
= +25°C, F
REQ
= 1.0 MHz,
V
CC
= 5.5V
(Note
1)
V
CC
= 1.8V, F
CLK
= 400 kHz
V
CC
= 5.5V, F
CLK
= 1 MHz
V
CC
= 5.5V, F
CLK
= 1 MHz
SCL = SDA = V
CC
= 1.8V
SCL = SDA = V
CC
= 5.5V
T
A
= -40°C to +85°C
Test Conditions
DC CHARACTERISTICS
Param.
Symbol
No.
D1
D2
D3
D4
D5
D6
D7
D8
D9
Note 1:
V
IH
V
IL
V
OL
I
LI
I
LO
C
INT
I
CCREAD
Operating Current
I
CCWRITE
Operating Current
I
CCS
Standby Current
This parameter is not tested, but is ensured by characterization.
DS20005772A-page 4
Preliminary
2017 Microchip Technology Inc.
24CW16X/24CW32X/24CW64X
TABLE 1-2:
AC CHARACTERISTICS
Electrical Characteristics:
Industrial (I):
V
CC
= 1.6V to 5.5V
Characteristic
Clock Frequency
Clock High Time
Clock Low Time
SDA and SCL Rise Time
SDA and SCL Fall Time
Min.
—
260
500
—
—
260
260
0
50
260
—
500
Max.
1000
—
—
1000
300
—
—
—
—
—
450
—
Units
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
T
A
= -40°C to +85°C:
Conditions
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
(Note
1)
1.6V
≤
V
CC
≤
5.5V
(Note
1)
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
(Note
2)
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
1.6V
≤
V
CC
≤
5.5V
AC CHARACTERISTICS
Param.
Symbol
No.
1
2
3
4
5
6
7
8
9
10
11
12
F
CLK
T
HIGH
T
LOW
T
R
T
F
T
HD
:
STA
Start Condition Hold Time
T
SU
:
STA
Start Condition Setup Time
T
HD
:
DAT
Data Input Hold Time
T
SU
:
DAT
Data Input Setup Time
T
SU
:
STO
Stop Condition Setup Time
T
AA
T
BUF
Output Valid from Clock
Bus Free Time: Bus Time
must be Free before a New
Transmission can Start
Input Filter Spike Suppression
(SDA and SCL pins)
Write Cycle Time
(byte or page)
Endurance
13
14
15
Note 1:
2:
3:
4:
T
SP
T
WC
—
—
1,000,000
50
5
—
ns
ms
(Note
3)
cycles V
CC
= 5.5V, +25°C,
per data byte
(Note
4)
The rise/fall times must be less than the specified maximums in order to achieve the maximum clock
frequencies specified for F
CLK
. Please refer to the I
2
C specification for applicable timings.
As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region of
the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
Not 100% tested. C
B
= total capacitance of one bus line in pF.
This parameter is not tested but ensured by characterization.
I want to use a state machine to make a PWM motor speed control, and use one button to set two functions.A short press within 1S turns the motor on or off, and a long press adjusts the speed by PWM. W...
[p=24, null, left][color=#333333] Power supply is the foundation of a system, and a good power supply design is the premise for the stable operation of the system. In actual projects, the most commonl...
I am using C6748 to process voice signals, and now I have some questions about the AIC31 chip. 1. The chip sound format seems to be 16-bit, 20-bit, 24-bit, and 32-bit. What are the different formats u...
The hardware welding of the 430[color=#000000]emulator[/color] is completed. What should I do if the[color=#000000]power[/color] indicator light is not on? It will only light up if the program is not ...
51mcu
京公网安备 11010802033920号
EEWORLD
